The effect of pre-wetting on dynamic contact angles

A roll-coating experimental system is used to study the effect of pre-wetting on dynamic contact angles, the interfacial displacement depth, and the associated phenomenon of air entrainment. The system consists of a roll, which is horizontally rotating in a liquid pool. The dynamic contact angle is recorded by a macrophotography system. The test liquids are glycerol solutions with viscosities in the range 104 < μ < 748 mPa · s. The value of (μV/ρg)^0.5 is taken as the characteristic length to be used in the dimensionless relationships which correlate experimental measurements. The effect of base layer entry angle into the liquid pool on the dynamic contact angles and other flow parameters is studied. Comparison is made with measurements in dry tape-coating and other pre-wet roll–coating systems.     

Effects of the cryogenic cooling on the fatigue strength of the AISI 304 stainless steel ground components

For environmental considerations, the substitution of the conventionally used oil-based grinding fluids has nowadays become strongly recommended. Although several alternatives have been proposed, cryogenic cooling by liquid nitrogen is the non-polluting coolant that has been given relatively more attention because of its very low temperature. In this investigation, in order to contribute to developing this promising cooling mode, its beneficial effects on the ground surface integrity of the AISI 304 stainless steel and their consequences on the fatigue lifetime are explored. Results of this investigation show that grinding under cryogenic cooling mode generates surfaces with lower roughness, less defects, higher work hardening and less tensile residual stresses than those obtained on surfaces ground under oil-based grinding fluid. These surface enhancements result into substantial improvements in the fatigue behaviour of components ground under this cooling mode. An increasing rate of almost 15% of the endurance limit at 2 × 10⁶ cycles could be realized. SEM analyses of the fatigue fracture surfaces have shown that the fatigue cracks observed on the specimens ground under cryogenic cooling are shorter (i.e., 30-50 μm) than those generated under oil-based cooling mode (i.e., 150-200 μm). The realized improvements in the surface integrity and in the fatigue behaviour are thought to be related to the reduction of the grinding zone temperature observed under cryogenic cooling, as no significant differences between the grinding force components for both cooling modes have been observed.     

Microstructure and mechanical properties of modified and non-modified stir-cast Al-Si hypoeutectic alloys

The microstructure and mechanical properties of modified and non-modified stir-cast commercial aluminium alloys A-S7G03 and A-S4G have been investigated. Stir casting of these alloys resulted in spherical and/or rosette shape primary -phase, and the eutectic silicon was broken into miniature needle morphology. This stir-cast structure slightly improved the mechanical properties in comparison to those of conventionally cast alloys, however the fracture of the stir-cast alloys revealed intergranular brittle fracture. The addition of 0.02% strontium, in the form of Al-5 mass% Sr master alloy, during stir casting modified the eutectic silicon into a very fine spheroidal morphology, while the -phase particle showed the same morphology as the stir-cast alloys. This novel structure resulted in significant improvement of mechanical properties. The elongation of the modified stir-cast alloys was five times greater than that of the non-modified one. A transgranular mode of fracture was observed for the modified stircast alloys, moreover smooth ripple and dimple patterns were observed reflecting the high ductility of the modified stir-cast alloys.     

Soluble Epoxide Hydrolase Blockade after Stroke Onset Protects Normal but Not Diabetic Mice

Soluble epoxide hydrolase (sEH) is abundant in the brain, is upregulated in type 2 diabetes mellitus (DM2), and is possible mediator of ischemic injury via the breakdown of neuroprotective epoxyeicosatrienoic acids (EETs). Prophylactic, pre-ischemic sEH blockade with 4-[[trans-4-[[(tricyclo[3.3.1.13,7]dec-1-ylamino)carbonyl]amino]cyclohexyl]oxy]-benzoic acid (tAUCB) reduces stroke-induced infarct in normal and diabetic mice, with larger neuroprotection in DM2. The present study tested whether benefit occurs in normal and DM2 mice if tAUCB is administered after stroke onset. We performed 60 min middle cerebral artery occlusion in young adult male C57BL mice divided into four groups: normal or DM2, with t-AUCB 2 mg/kg or vehicle 30 min before reperfusion. Endpoints were (1) cerebral blood flow (CBF) by laser Doppler, and (2) brain infarct at 24 h. In nondiabetic mice, t-AUCB reduced infarct size by 30% compared to vehicle-treated mice in the cortex (31.4 ± 4 vs. 43.8 ± 3 (SEM)%, respectively) and 26% in the whole hemisphere (26.3 ± 3 vs. 35.2 ± 2%, both p < 0.05). In contrast, in DM2 mice, tAUCB failed to ameliorate either cortical or hemispheric injury. No differences were seen in CBF. We conclude that tAUCB administered after ischemic stroke onset exerts brain protection in nondiabetic but not DM2 mice, that the neuroprotection appears independent of changes in gross CBF, and that DM2-induced hyperglycemia abolishes t-AUCB-mediated neuroprotection after stroke onset.     

Effect of plasticizers on the thermal decomposition of chlorinated polyvinylchloride

Plasticized samples of chlorinated polyvinylchloride (CPVC) were investigated by using thermogravimetric (TG) analysis and differential scanning calorimetry (DSC). Three different plasticizers were studied, namely, dioctyl phthalate (DOP), alkyldiaryl phosphate ester (Santiciser 2148), and triaryl phosphate ester (Reofos 50). TG experiments in nitrogen showed one major decomposition stage, involving dehydrochlorination, and minor pyrolysis reaction of the hydrocarbon residue. In contrast to the three stages previously reported to occur in the nonplasticized‐stabilized CPVC, TG analyses in air showed two distinctive decomposition stages for the plasticized CPVC samples. The DOP system provided a suggestion of a third stage. The first decomposition stage was due not only to the loss of all the chlorine present, but also to loss of the plasticizer or its decomposition products. The second decomposition stage was mostly due to char oxidation, the char being formed almost exclusively from the DCE and VDC units in CPVC polymer. DSC results showed that in the presence of nitrogen, there was no significant plasticizer effect on the thermal decomposition behavior of CPVC up to about 330°C, while in air the DSC traces also show no significant differences below 400°C. The two phosphate plasticizers showed no significant differences in their effect on the thermal decomposition behavior of CPVC under the same experimental conditions. It is believed that P₂O₅ and polyphosphoric acid are among the main constituents of the residua. These would impart a protective glassy surface to the char. This will facilitate effective flame retardant action. This preliminary conclusion is based on the premise that the more stable the char layers are, the more resilient will be the protective layer, and consequently, the better the flame retardant effect. J. VINYL ADDIT. TECHNOL., 11:21–27, 2005. © 2005 Society of Plastics Engineers     

Application of orthogonal collocations to some transport phenomena problems in co-axial cylinders and spheres

Collocation methods are developed for the solution of some differential equation models for transport phenomena problems in one-and two-dimensions in co-axial annuli of spherical and cylindrical shapes. General formulae are developed to obtain orthogonal polynomials over an arbitrary interval using two types of weighting functions. The convergence and accuracy of the methods are demonstrated using two test problems, i.e., calculation of effectiveness factors in (a) a spherical pellet with peripherally deposited catalyst and (b) a Raschig ring type cylindrical catalyst pellet. Comparisons of results obtained from the present methods with analytic solutions for the first-order reactions indicate good agreement. Numerical solutions are also obtained for the second-and the third-order reactions for which analytic solutions are not available. Results obtained in terms of a new Thiele modulus involving the ratio of volume of peripherally deposited part of catalyst to exterior surface area indicate that this normalization brings effectiveness factor versus Thiele modulus curves close together for co-axial spherical and long cylindrical pellets, as it does for these geometries without the inner co-axial portion.     

A transient method for characterizing flow regimes in a circulating fluid bed

In recent years, although an increasing number of literature have been devoted to circulating fluidized bed (CFB), the prediction of velocities over which different fluidization regimes exist is still difficult. In this study, a transient method was applied which readily allows one to identify operational features and critical transitions. The method is based on stopping the solids flow rate into the riser when riser is operating in fully dense transport regime. The analysis of transient pressure drop data across the riser during a solids flow cut-off experiment against its time derivative demonstrate the three distinct operating regimes that exist as the gas deplete the solid out of the riser. The transient was compared to data taken under steady state operations using statistically designed experiments. Results indicated that although there were significant differences when comparing operations in dilute conditions, there were no significant differences between the two methods in the fast fluidized and dense transport regimes. The transient method was capable of reproducing the solids circulation dependence on riser solids holdup and on the axial pressure profile. This transient method offers an accurate, easy, rapid, and reproducible means of characterizing CFB operations over a wide range of flow conditions. The lack of accuracy in the dilute regime is conjectured to be due to the wide particle size distribution that resulted in segregation during the transient testing.     

QoS aggregation for service orchestrations based on workflow pattern rules and MCDM method: evaluation at design time and runtime

Service consumers satisfaction is considered today as one of the main concern to be ensured by service providers, especially with the spread of concurrency and the increase of functionally equivalent services. This satisfaction is closely related to quality of service (QoS) perceived by service consumers. In this context, we propose an approach to determine the satisfaction degree corresponding to the QoS of service-based applications, with regard to service consumers’ QoS expectations. Our approach is based on a preference model, which is built only on the basis of service consumer’s provided information. This preference model is also based on the 2-additive Choquet operator that takes into account preferential dependencies. In this paper, we target both design time and runtime aggregation of QoS of service-based applications.