Craze yielding and fracture mechanism in PE/PS/PE laminated films

The change in polystyrene (PS) layer thickness, which has been simultaneously determined during post-yield deformation, shows that crazing is the basic mechanism of toughening in all laminated films, and that shear deformation supplements the contribution of crazing especially for samples with high polyethylene (PE) volume fractions. Crazes formed in PS layers in the laminated films are slender and regular compared with the short and lenticular crazes formed in bulk PS film. When PE volume fraction increased, craze advance speed decreased because of the reduction of the stress concentration effect at craze tips. The life-time of the first mature craze to be formed at a given strain rate increased with PE volume fraction because the PE supporting the mature crazes could effectively inhibit craze rupture and blunt out the propagating crack by absorbing the stored elastic energy in the PS layer that would have been dissipated as fracture surface energy.     

Performance analysis of disk allocation method usingerror-correcting codes

The problem of distributing a Cartesian product file on multiple disks to maximize the parallelism for partial match queries is addressed. C. Faloutsos et al. (1989) have proposed an allocation method for Cartesian product files on multiple disks by using linear error-correcting codes. The performance of the allocation method is analyzed. Some conditions under which the allocation method is strictly optimal for queries with a given number of unspecified attributes are presented. A necessary and sufficient condition for a linear code to give a strictly optimal allocation method is discussed. Formulas for the average response time on queries with w unspecified attributes, denoted T_w, in terms of the weight distribution of the code or its dual code, and formulas for the average response time Ton all queries, are given. Several examples whose average response times T_w or T are close to theoretical lower bounds are presented     

The heat transfer and pressure drop characteristics of finned tube banks in forced convection (effects of fin height on pressure drop characteristics)

In recent years the requirement for the reduction of energy consumption has been increasing to solve the problems of global warming and the shortage of petroleum resources. For example, in the power generation field, as thermal power generation occupied 60% of the power generation demand, considerable improvement of the thermal efficiency is required. This paper describes the pressure drop characteristics of finned tube banks used for heat exchangers in thermal power generation that were clarified by testing serrated finned tube banks with different fin heights for improved heat transfer and conventional spiral finned tube banks with different fin heights, and an equation to predict pressure drop which is necessary for the heat exchanger design is proposed. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(3): 179–193, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20112     

Thermal properties of poly(tetramethyl-p-silphenylene siloxane) and (tetramethyl-p-silphenylene siloxane-dimethyl siloxane) copolymers

Some physical properties of poly(tetramethyl-p-silphenylene siloxane) homopolymer and random block copolymers of tetramethyl-p-silphenylene siloxane-dimethyl siloxane have been determined and correlated with polymer structure. Differential scanning calorimetry (d.s.c.), differential thermal analysis (d.t.a.), density gradient column measurements and optical hot stage melting point determination and diluent techniques were used. The thermodynamic melting temperature of the homopolymer was estimated to be 160°C and its heat of fusion, ΔH_u, found to be 54.4 J/g (13 cal/g or 2710 cal/mol of monomer repeat units). Its limiting glass transition temperature, T_g, was ?20°C. T_g of the copolymer was found to vary almost monotonically with increasing dimethyl siloxane (DMS) content ranging from ?20° (0% DMS) to just above ?123°C, for pure DMS polymer. The copolymer melting temperature was found to increase as the fraction of the crystalline (hard) TMPS constituent was increased. Based upon copolymer theory and extrapolated melting point data, it was estimated that the block size of soft DMS component in the copolymer most probably consists of twelve monomer units distributed amongst TMPS sequences of varying length.     

Refined mapping of a gene responsible for Fukuyama-type congenital muscular dystrophy: evidence for strong linkage disequilibrium

Fukuyama-type congenital muscular dystrophy (FCMD), the second most common form of childhood muscular dystrophy in Japan, is an autosomal recessive severe muscular dystrophy associated with an anomaly of the brain. After our initial mapping of the FCMD locus to chromosome 9q31-33, we further defined the locus within a region of approximately 5 cM between loci D9S127 and CA246, by homozygosity mapping in patients born to consanguineous marriages and by recombination analyses in other families. We also found evidence for strong linkage disequilibrium between FCMD and a polymorphic microsatellite marker, mfd220, which showed no recombination and a lod score of (Z) 17.49. A "111-bp" allele for the mfd220 locus was observed in 22 (34%) of 64 FCMD chromosomes, but it was present in only 1 of 120 normal chromosomes. This allelic association with FCMD was highly significant (chi 2 = 50.7; P < .0001). Hence, we suspect that the FCMD gene could lie within a few hundred kilobases of the mfd220 locus.     

Probabilistic Strength at Serviceability Limit State for Normal and SBHS Slender Stiffened Plates Under Uniaxial Compression

International Journal of Steel Structures - Stiffened plates with high slenderness parameters show large out-of-plane deflections, due to elastic buckling, which may occur before the plates reach...     

Heat transfer and pressure loss characteristics of a heat exchanger for recovering latent heat (effects of straight fin length and fin pitch on the heat transfer and pressure loss characteristics)

In recent years, the requirement for the reduction of energy consumption has been increasing to solve the problems of global warming and the shortage of petroleum resources. A latent heat recovery type heat exchanger is one of the effective methods for improving thermal efficiency by recovering latent heat. This paper describes the heat transfer and pressure loss characteristics of a latent heat recovery type heat exchanger having straight fins (fin length: 65 mm or 100 mm, fin pitch: 2.5 mm or 4 mm). These were clarified by measuring the exchange heat quantity, the pressure loss of the heat exchanger, and the heat transfer coefficient between the outer fin surface and gas. The effects of fin length and fin pitch on heat transfer and pressure loss characteristics were clarified. Furthermore, equations for predicting the heat transfer coefficient and pressure loss which are necessary for heat exchanger design were proposed. ©2007 Wiley Periodicals, Inc. Heat Trans Asian Res, 36(4): 230– 247, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20153 Copyright © 2004 Wiley Periodicals, Inc.     

The Thermal Stability of Linear Trans-quinacridone Pigments

Although linear trans-quinacridone was first synthesized some forty years ago, it has appeared as a commercial pigment much more recently and was the first red pigment of a new chemical class for a very long time. It can be prepared with a number of different crystal structures all having the same chemical formula, but different hues. The γ-form is the most stable. The transformations between this form and the β-form, which can be brought about by heat and solvents, have been examined by a combination of differential thermal analysis, scanning electron microscopy and X-ray diffraction.