Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

Measurement of histamine release from human lung tissue ex vivo by microdialysis technique

OBJECTIVE AND DESIGN: Currently no method is available for measurement of mediator release from intact human lung. In this study, a microdialysis technique was used to measure histamine release from mast cells in human lung tissue ex vivo. MATERIAL: Microdialysis fibers of 216 microm were inserted into lung tissue and perfused with Krebs Ringer buffer at a rate of 3 microl/min. After a 15 min period of steady-state perfusion, anti-IgE and vehicle were injected into the lung tissue above individual fibers. Samples from each fibre were collected for 20 min at 2 min intervals. Histamine was assayed fluorometrically. RESULTS: Anti-IgE concentrations of 40-40,000 U/ml dose-dependently released histamine, significant histamine release being demonstrated with anti-IgE concentrations of 400 U/ml and greater. The kinetics of histamine release showed peak values 2-8 min after the injection. Great individual responses were observed but data could be reproduced within individual donors. Monocyte chemoattractant protein-1, a potent basophil secretagogue, did not induce histamine release in lung tissue which indicated mast cells to be the histamine source. Substance P did not release histamine in the lung tissue. CONCLUSIONS: The microdialysis technique allowed measurements of histamine release from mast cells in intact lung ex vivo. The method may prove useful since a number of experiments can be performed in a few hours in intact lung tissue without any dispersion or enzymatic treatment.     

Importance of Mullins effect in commercial silicone elastomer formulations for soft robotics

Silicone elastomers are used in a wide range of applications, including artificial muscles, biomedical devices, and soft robotics, for which chemical, thermal, and mechanical stability are important requirements that these elastomers must fulfill. However, to ensure that silicone elastomers' properties and performance remain constant under long-term deployment, it is necessary to examine and account for the Mullins effect, which has the potential to significantly alter certain elastomer properties of interest. In this article, the mechanical properties of soft and hard commercial silicone elastomers and two blends of commercial silicone elastomers are investigated—specifically their softening behavior due to the Mullins effect. Ultimate stresses, ultimate strains, and Young's moduli are obtained from uniaxial tensile tests. Results show that the point of softening greatly depends on both the elastomer type and its strain history. Furthermore, a significant permanent set is observed in the softest commercial formulations.     

Classification of slice-based VBR video traffic and estimation of link loss by exceedance

Classification of a video stream is an essential preliminary step to estimate the bit loss when the video stream is transmitted over a communication network. In this paper, we classify the video frames by the average frame size and estimate the bit loss for each class when the bitrate exceeds the capacity of the bottleneck link. The video stream under study is encoded using the explicit slice-based H.264/AVC encoding scheme. This scheme reduces the burstiness of regular H.264/AVC encoded video by removing the traditional GOP structure. Instead, a repetitive combination of intracoded and predicted slices is employed, thereby introducing a specific dependence structure in the video data. We consider a bufferless model of the communication system and evaluate the channel capacity required to give a maximum allowed loss rate for each class.Due to the high variability, non-stationarity and non-homogeneity of the underlying video data, the obtained classes are checked regarding the dependence and distribution structure of the data. The high quantiles of the losses are estimated for each class.     

Optimization Techniques for Improving the Performance of Silicone‐Based Dielectric Elastomers

Dielectric elastomers are possible candidates for realizing products that are in high demand by society, such as soft robotics and prosthetics, tactile displays, and smart wearables. Diverse and advanced products based on dielectric elastomers are available; however, no elastomer has proven ideal for all types of products. Silicone elastomers, though, are the most promising type of elastomer when viewed from a reliability perspective, since in normal conditions they do not undergo any chemical degradation or mechanical ageing/relaxation. Within this review, different pathways for improving the electro‐mechanical performance of dielectric elastomers are highlighted. Various optimization methods for improved energy transduction are investigated and discussed, with special emphasis placed on the promise each method holds. The compositing and blending of elastomers are shown to be simple, versatile methods that can solve a number of optimization issues. More complicated methods, involving chemical modification of the silicone backbone as well as controlling the network structure for improved mechanical properties, are shown to solve yet more issues. From the analysis, it is obvious that there is not a single optimization technique that will lead to the universal optimization of dielectric elastomer films, though each method may lead to elastomers with certain features, and thus certain potentials.

     

Measuring the coolness of interactive products: the COOL questionnaire

Coolness has recently started to be explored as a design goal for interactive products from practitioners as well as researchers within human–computer interaction (HCI), but there is still a need to further operationalise the concept and explore how we can measure it. Our contribution in this paper is the COOL questionnaire. We based the creation of the questionnaire on literature suggesting that perceived coolness is decomposed to outer cool (the style of a product) and inner cool (the personality characteristics assigned to it). In this paper, we focused on inner cool, and we identified 11 inner cool characteristics. These were used to create an initial pool of question items and 2236 participants were asked to assess 16 mobile devices. By performing exploratory and confirmatory factor analyses, we identified three factors that can measure the perceived inner coolness of interactive products: desirability, rebelliousness and usability. These factors and their underlying 16 question items comprise the COOL questionnaire. The whole process of creating the questionnaire is presented in detail in this paper and we conclude by discussing our work against related work on coolness and HCI.     

Life-cycle modeling for adaptive and variant design. Part 1: Methodology

Life-cycle modeling for design (LCMD) is a methodology for assessing the life-cycle impacts for a complex product with many individual components starting from initial design phases when few design specifications have been made. The methodology combines life-cycle assessment (LCA) with probabilistic design methods in a way that forecasts attributes of possible final designs yet reduces information needs. Specifically, LCMD is a methodology for generating arrays of design scenarios that communicate the range of designs being considered by a design team, and estimating missing data for those design scenarios. The main contribution to enhancing standard LCA is the incorporation of methods to estimate physical attributes of individual components for various design options and in four analyses for evaluating the arrays of design scenarios. An automotive case study presented in part 2 of this work demonstrates one application of LCMD.     

Designing on-site: Facilitating participatory contextual architecture with mobile phones

Some movements within modern architecture particularly emphasise the importance of matching buildings to their surroundings. However, practicing such “contextual architecture” is highly challenging and typically not something the future inhabitants of a building are well equipped for participating in. This paper explores the potentials of using mobile phone technology for facilitating such client participation in the parts of an architecture process that take place on the building site. For this we introduce ArchiLens, a mobile system for interactive on-site 3D visualisation of houses, and findings from a field study with 40 participants in the process of building or modifying their home. The study showed that using the system helped evoke people’s imagination of the look and feel of their future house, and envision it in context. This enabled them to participate more closely in the design process on-site by iteratively reviewing design alternatives and exploring, for example, other placements and materials.     

Performance Study of a Closed-Type Heat Pump Tumble Dryer Using a Simulation Model and an Experimental Set-Up

In the interests of competitiveness, manufactures of tumble dryers are seeking to reduce both their electricity use and the drying time. This study examines how the cylinder volume of the compressor and the total heat transfer of the condenser influence the drying time and electricity use in a heat pump tumble dryer. A transient simulation model was developed and compared to an experimental set-up with good similarity. The simulations show that increasing the cylinder volume of the compressor by 50% decreases the drying time by 14% without using more electricity.