HA/β-TCP plasma sprayed coatings on Ti substrate for biomedical applications

The present work focuses on the fabrication of βTCP (β-tricalcium phosphate) and HA/βTCP (hydroxyapatite/β-tricalcium phosphate) composite coatings by plasma spraying. The starting powders were produced via solid-state method using 2 wt% MgO to stabilize βTCP phase. The synthesized powders were preliminarily granulated to be used by the plasma spray process. Coatings obtained on titanium substrates are uniform and well adherent but due to the high temperature and cooling rate typical for plasma spraying process, βTCP phase is almost totally transformed into the α allotrope. Thermal treatment at 800 °C allows the reconversion of the phase αTCP→ βTCP. It is therefore possible to produce coatings with tuneable dissolution properties by selecting the proper initial powder mixture and the specific thermal treatment.     

Effect of electric field on the hydrodynamics of fluidized nanoparticles

The effect of electric field on the hydrodynamics of nanoparticles was studied in a fluidized rectangular bed, with electrodes attached to two parallel walls. It was shown that the electric field of the order of 3 times the gravity markedly decreased the bed expansion and increased the solids volume fraction of nanoparticles fluidized by air. In these experiments, a light diode assembly was utilized to infer the local solids volume fractions within a rectangular bed of 10 nm silica particles. These experimental measurements yielded a two dimensional solids volume fraction distribution within the rectangular bed. The experimental results provided some new insights into the distribution of solids within the bed. The agglomerate diameters were computed using a momentum balance with the drag given by the Ergun equation and the empirical Richardson-Zaki method. Both methods yielded agglomerate diameters of the order of 100 μm and showed dependence on the strength of the electric field. The electric field decreased the granular temperature of the nanoparticles.     

A Low-Power Wide-Dynamic-Range Analog VLSI Cochlea

Low-power wide-dynamic-range systems are extremely hard to build. The biological cochlea is one of the most awesome examples of such a system: It can sense sounds over 12 orders of magnitude in intensity, with an estimated power dissipation of only a few tens of microwatts. In this paper, we describe an analog electronic cochlea that processes sounds over 6 orders of magnitude in intensity, and that dissipates 0.5 mW. This 117-stage, 100 Hz to 10 KHz cochlea has the widest dynamic range of any artificial cochlea built to date. The wide dynamic range is attained through the use of a wide-linear-range transconductance amplifier, of a low-noise filter topology, of dynamic gain control (AGC) at each cochlear stage, and of an architecture that we refer to as overlapping cochlear cascades. The operation of the cochlea is made robust through the use of automatic offset-compensation circuitry. A BiCMOS circuit approach helps us to attain nearly scale-invariant behavior and good matching at all frequencies. The synthesis and analysis of our artificial cochlea yields insight into why the human cochlea uses an active traveling-wave mechanism to sense sounds, instead of using bandpass filters. The low power, wide dynamic range, and biological realism make our cochlea well suited as a front end for cochlear implants.     

A rule-based fuzzy-logic approach for the measurement of manufacturing flexibility

Manufacturing flexibility is a difficult to quantify concept that defies universal definition. This paper presents a novel fuzzy-logic approach for measuring manufacturing flexibility that exploits linguistic variables for quantifying pertinent factors affecting commonly utilized flexibility types. Towards this end, we identify and measure the contribution of specified state variables towards the assumed flexibility types in order to compute an overall flexibility index for a generic manufacturing system. The suggested framework provides a convenient end user approach amenable to software implementation that is exemplified through the development of a prototypical software tool called “Flexibility Evaluator”.     

Demonstration of a semiconductor external cavity laser using a UVwritten grating in a planar silica waveguide

The authors report the first demonstration of a semiconductor external cavity waveguide laser, modulated at 2.5 Gbit/s over 100 km of standard optical fibre using a UV written grating in a planar silica waveguide as the feedback element     

Performance Optimizations for Deploying VoIP Services in Mesh Networks

In the recent past, there has been a tremendous increase in the popularity of VoIP services as a result of huge growth in broadband access. The same voice-over-Internet protocol (VoIP) service poses new challenges when deployed over a wireless mesh network, while enabling users to make voice calls using WiFi phones. Packet losses and delay due to interference in a multiple-hop mesh network with limited capacity can significantly degrade the end-to-end VoIP call quality. In this work, we discuss the basic requirements for efficient deployment of VoIP services over a mesh network. We present and evaluate practical optimizing techniques that can enhance the network capacity, maintain the VoIP quality and handle user mobility efficiently. Extensive experiments conducted on a real testbed and ns-2 provide insights into the performance issues and demonstrate the level of improvement that can be obtained by the proposed techniques. Specifically, we find that packet aggregation along with header compression can increase the number of supported VoIP calls in a multihop network by 2-3 times. The proposed fast path switching is highly effective in maintaining the VoIP quality. Our fast handoff scheme achieves almost negligible disruption during calls to roaming clients     

Design development of a static sunshade using small scale modeling technique

The rising global demand for energy has triggered emphasis on conservation of energy. Buildings are one of the important energy consuming sectors. Passive solar architecture encompasses a wide range of strategies and options resulting in energy efficient building design and increased occupant's comfort. Passive solar design, aiming at increasing direct solar gains during winter period and to avoid overheating during summer period should make use of specific shading devices over energy efficient window. The static sunshades are most effective for solar control inside the buildings.Countries like India have composite climate, which can be classified under summer, winter and rainy season. Depending on the seasonal requirements, this paper introduces a new geometry of a static sunshade, designed by calculating the sun angles for the two dates. The static sun shading design methodology is validated with the help of small scale modeling experimentation technique, carried out in Pilani, Rajasthan (India). Although insulating materials can be used as a part of a building structure, its feasibility should be checked before particular application. In the present paper, the two small-scale experimental models of actual construction material with varying static sunshades, i.e. horizontal and the proposed one have been constructed and analyzed with the models of insulating material (Polyurethane Foam [PUF]). Depending upon the solar intersection over south facade wall, sunlit area and shaded area have been correlated with temperature inside the models to decide the effectiveness of the proposed sunshade.     

Experimental demonstration of step-like dispersion profiling inoptical fibre for soliton pulse generation and compression

Generation of 100 GHz trains of 500-700 fs pulses using dual-frequency beat conversion in a step-like dispersion profiled fibre is reported. The authors believe that this is the first time the generation and compression of soliton pulses using such a fibre has been demonstrated. The fabrication of such fibre assemblies does not require any special facilities and relies only on conventional optical fibre technology. They believe that the use of profiling the fibre dispersion by fibre segments instead of continuously dispersion-decreasing fibre is not only possible but preferable in many applications