Rheological properties of bitumen in water emulsions with added solids

Experimental work was carried out to investigate the rheological properties of bitumen in water emulsions containing solids of different shape and size. The bitumen volumetric concentration was varied up to 60%, solids free basis, and the solids volume fraction (total volume basis) was varied up to 0.2. Irregular-shaped silica sand (average diameter: 9 and 33 μm) and smooth spherical glass beads (average diameter: 27 and 44 μm) were used as the added solids. In the low shear stress range, shear thinning behavior was observed for bitumen in water emulsions. At high shear stress, the viscosity of the emulsions became fairly independent of the shear stress. The addition of solids to the bitumen emulsions increased the mixture viscosity. The addition of irregular-shaped silica sand gave a higher viscosity than a similar addition of the spherical glass beads. The viscosity of the emulsion/solids mixtures was influenced by the solids size as well; the smaller size particles gave a higher viscosity. The addition of solids to the bitumen emulsions also induced shear thickening (dilatancy) behavior at high solids volume fraction. The degree of the shear thickening increased with the oil concentration.     

Rheology of oil in water emulsions with added solids

The effect of added solids on the rheology of oil in water emulsions was investigated. The range of the oil concentration, solids free basis, was (0-70%) and the solids volume fraction was (0-0.16). The solids mean diameter was 45 μm and it was about four times larger than the oil droplets. In the absence of added solids, non-Newtonian behaviour was observed for oil concentrations above 40%. The added solids increased the emulsion viscosity in a manner similar to the addition of solids to a homogeneous fluid. The rheological data of all the emulsion-solids mixtures investigated were correlated as relative viscosity versus solids volume fraction, where the relative viscosity is defined as the ratio of the emulsion-solids mixture viscosity to the solids-free emulsion viscosity. In the case of non-Newtonian systems, the emulsion-solids mixture viscosity and the solids-free emulsion viscosity were calculated at the same shear stress. The Barnea and Mizrahi viscosity correlation was found to fit the data well.     

On the applicability of diploid genetic algorithms in dynamic environments

Diploid genetic algorithms (DGAs) promise robustness as against simple genetic algorithms which only work towards optimization. Moreover, these algorithms outperform others in dynamic environments. The work examines the theoretical aspect of the concept by examining the existing literature. The present work takes the example of dynamic TSP to compare greedy approach, genetic algorithms and DGAs. The work also implements a greedy genetic approach for the problem. In the experiments carried out, the three variants of dominance were implemented and 115 runs proved the point that none of them outperforms the other.     

Effect of Ni7+ Ion Irradiation on Structure and Ammonia Sensing Properties of Thermally Oxidized Zinc and Indium Films

ZnO and In2O3 films were prepared by thermal oxidation of vacuum deposited zinc and indium films, respectively onto the glass substrate at 30 C. The fabricated films have been irradiated with 100-MeV Ni7+ ions at different fluences ranging from 5×1011 to 5×1013 ions/cm2. The structural and gas sensing properties of pristine and irradiated films have been discussed. X-ray diffraction (XRD) pattern of pristine and irradiated films reveal that the films are polycrystalline in nature and crystallinity increases after irradiation. In this study, highly porous In2O3 nanorods evolved when being irradiated at a fluence of 5×1013 ions/cm2 while ZnO film shows decrease in number of nanowires. The ammonia sensing performance of the Ni7+ irradiated In2O3 films shows an improvement as compared to its pristine counterpart.     

Mineralogical Studies of Coal Fly Ash for Soil Application in Agriculture

Coal fly ash procured from Guru Gobind Singh Super Thermal Power Plant, Ropar, Punjab, India, was analyzed for its mineralogical content and thermal stability by x-ray diffraction (XRD), thermal gravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), and physicochemical properties. XRD studies showed that major crystalline phases observed were quartz (SiO₂) and aluminum silicon oxide (Al_4.52Si₁.₄₈) with macro- and microelement (N, P, K, Mg, Zn, S, and Fe). Fly ash showed thermal stability up to 500°C and reduction in weight was up to 200°C, primarily due to loss of water and decarboxylation as revealed by TGA plots. FTIR of fly ash showed that the most prominent peaks in the spectra corresponded to Si–O and Al–O stretch vibrations. Coarse-grain accumulation of fly ash indicated the presence of 70% of fine-grained particles of 0.075 mm. Coal fly ash was alkaline in nature (pH 7.85 ± 0.03) with an electrical conductivity of 0.14 ± 0.02 µS m^?1, water holding capacity of 62%, low bulk density of 0.99 g cm^?3, and a surface area of 0.96 m² g^?1. With properties similar to that of soil coal, fly ash represents a suitable material for use in specific quantities as a soil amending agent in agriculture.     

Study of crystal structure,dielectric, magnetic and magnetoelecrtic properties of xCoFe2O4-(1-x)Na0.5Bi0.5TiO3 composites

Multiferroic composites of spinel ferrite and ferroelectric xCoFe₂O₄ – (1-x)Na_0.5Bi_0.5TiO₃ (with x = 0.10,0.30,0.50) were efficiently prepared by standard solid state reaction mechanism. X-ray diffractometer was used to analyze crystal structure of the prepared composites. The observed XRD patterns of the composites comprise peaks of both the phases i.e. ferrite and ferroelectric, with no sign of secondary peaks. Rietveld refinement of XRD data further confirms the coexistence of these two phases with cubic (Fd3m) and rhombohedral (R3c) symmetry corresponding to ferrite and ferroelectric phase respectively. The 3-dimensional overview of crystal structure of pure CoFe₂O₄ and Na_0.5Bi_0.5TiO₃ and of composite 0.50CoFe₂O₄?0.50Na_0.5Bi_0.5TiO₃ is generated by using refined parameters. The dielectric constant (ε´) and dielectric loss (tanδ) values were recorded as a function of frequency ranging from 100?Hz to 7?MHz and at different temperatures. Both ε´ and tanδ follow dispersion pattern at lower frequencies while show frequency independent behavior at higher frequencies. The magnetic evaluation carried by analyzing M-H hysteresis loop reveals the ferrimagnetic characteristics of these composites. The highest value of magnetic moment is 1.12μ_B observed for composite 0.50CoFe₂O₄ – 0.50Na_0.5Bi_0.5TiO_3. Magnetoelectric (ME) voltage coefficient (α) was also demonstrated to observe the interaction between ferrite and ferroelectric phases. The highest value of α (72.72μV/Oe cm) is obtained for low ferrite composition 0.10CoFe₂O₄ – 0.90Na_0.5Bi_0.5TiO₃, which suggests the dependence of magnetoelectric response on the resistivity of the composites.