To provide a basis for the selection of suitable emulsifiers in oil-in-water emulsions used as tissue analogs for MRI experiments. Three different emulsifiers were investigated with regard to their ability to stabilize tissue-like oil-in-water emulsions. Furthermore, MR signal properties of the emulsifiers themselves and influences on relaxation times and ADC values of the aqueous phase were investigated.
Materials and methods
Polysorbate 60, sodium dodecyl sulfate (SDS) and soy lecithin were used as emulsifiers. MR characteristics of emulsifiers were assessed in aqueous solutions and their function as a stabilizer was examined in oil-in-water emulsions of varying fat content (10, 20, 30, 40, 50%). Stability and homogeneity of the oil-in-water emulsions were evaluated with a delay of 3 h and 9 h after preparation using T1 mapping and visual control. Signal properties of the emulsifiers were investigated by 1H-MRS in aqueous emulsifier solutions. Relaxometry and diffusion weighted MRI (DWI) were performed to investigate the effect of various emulsifier concentrations on relaxation times (T1 and T2) and ADC values of aqueous solutions.
Results
Emulsions stabilized by polysorbate 60 or soy lecithin were stable and homogeneous across all tested fat fractions. In contrast, emulsions with SDS showed a significantly lower stability and homogeneity. Recorded T1 maps revealed marked creaming of oil droplets in almost all of the emulsions with SDS. The spectral analysis showed several additional signals for polysorbate and SDS. However, lecithin remained invisible in 1H-MRS. Relaxometry and DWI revealed different influences of the emulsifiers on water: Polysorbate and SDS showed only minor effects on relaxation times and ADC values of aqueous solutions, whereas lecithin showed a strong decrease in both relaxation times (r1,lecithin = 0.11 wt.%−1 s−1, r2,lecithin = 0.57 wt.%−1 s−1) and ADC value (Δ(ADC)lecithin = − 0.18 × 10–3 mm2/s⋅wt.%) with increasing concentration.
Conclusion
Lecithin is suggested as the preferred emulsifier of oil-in-water emulsions in MRI as it shows a high stabilizing ability and remains invisible in MRI experiments. In addition, lecithin is suitable as an alternative means of adjusting relaxation times and ADC values of water.
Many critical issues need to be addressed when microstructured reactors are manufactured in large unit volumes. The most crucial of these are cost, ease of production, and reliability. The lack of breakthrough manufacturing technology to provide high‐efficiency, low‐cost, high‐precision plates is a hindrance to the early market implementation of systems requiring metallic microstructured plates. This contribution focuses on the development and optimization of a combined embossing and bending tool for the quick and continuous manufacture of easily machined plates. 相似文献
Furthering G. W. Allport's (1954) contentions for optimal contact, the authors introduce a new construct: the perceived importance of contact. They propose that perceived importance is the best proximal predictor of contact's reduction of prejudice. If individuals have opportunities for contact at work or in the neighborhood, their chances to have intergroup acquaintances and friends increase. Intergroup contact among acquaintances and friends can be perceived as more or less important, which in turn determines intergroup evaluations. A 1st study shows that the new measure of perceived importance is indeed distinct from established quantity and quality indicators. The results are cross-validated in a 2nd study that also sheds light on the meaning of importance. In 3rd and 4th studies, structural equation analyses and a meta-analysis support the hypotheses. (PsycINFO Database Record (c) 2010 APA, all rights reserved) 相似文献
Industrial pelletizing of sawdust was carried out as a designed experiment in the factors: sawdust moisture content, fractions of fresh pine, stored pine and spruce. The process parameters and response variables were energy consumption, pellet flow rate, pellet bulk density, durability and moisture content. The final data consisted of twelve industrial scale runs. Because of the many response variables, data evaluation was by principal component analysis of a 12 × 9 data matrix. The two principal component model showed a clustering of samples, with a good reproducibility of the center points. It also showed a positive correlation of energy consumption, bulk density and durability all negatively correlated to flow rate and moisture content. The stored pine was more related to high durability and bulk density. The role of the spruce fraction was unclear. The design matrix, augmented with the process parameters was a 12 × 6 matrix. Partial least squares regression showed excellent results for pellet moisture content and bulk density. The model for durability was promising. A 12 × 21 data matrix of fatty- and resin acid concentrations measured by GC–MS showed the differences between fresh and stored pine very clearly. The influence of the spruce fraction was less clear. However, the influence of the fatty- and resin acids on the pelletizing process could not be confirmed, indicating that other differences between fresh and stored pine sawdust have to be investigated. This work shows that it is possible to design the pelletizing process for moderate energy consumption and high pellet quality. 相似文献
An advanced learning system for interactive simulation of patient cases (ISP) is described. The system was designed to meet specific pedagogical needs where student activation and problem orientation were two of the key issues. The system includes features such as video based illness history-taking function using free text input, highly interactive physiological examination procedures, extensive laboratory tests and detailed user feedback. The system was constructed mainly in Authorware Professional, starting more than 10 years ago, and it is now available in refined versions in different languages. Twelve pedagogical and three technical features were initially defined for the project. All of these aims were fulfilled. The ISP system has been successfully used in education, and in international collaboration, including three applicability field tests. The system is also a powerful research tool for studying for instance medical decision-making. 相似文献
The high purchasing price of organic solvents has stimulated interest in their recovery from emissions. While conventional adsorption units for recovery of monosolvents have been in industrial use for some 70 years, it has hitherto proved impossible to costeffectively desorb solvent fractions sufficiently pure for direct use in the case of emissions of mixtures. The solvent mixtures obtained by desorption had to be separated in expensive rectification steps, with the high costs thus precluding widespread use of adsorption for recovery projects in the chemical and printing industries. After conclusion of development work performed in the USA and Germany over a period of 10 years, it is now possible to control the adsorption steps in such a way that the purities necessary for reutilisation of the individual solvent fractions can be attained without the aid of rectification steps. 相似文献
Porosity and uncombined carbon in cemented carbides are traditionally assessed by comparison to standardized microstructure charts, such as those in ISO 4505-1978. To improve the accuracy in the characterization a fully automatic image analysis procedure has been developed. The analysis is performed using light optical microscopy on unetched polished specimens. The implemented algorithm separates uncombined carbon, C-defects, from pores, A- and B-defects. Pores are approximately distributed in a random way in the structure. Uncombined carbon is on the other hand precipitated into clusters of carbon particles. This difference is together with defect size used as a base for the separation. Small defects situated close together are classified as C-defects, small isolated defects as A-pores and large defects as B-pores. Pores are found to be more round than the somewhat elongated C-defects. The difference in shape is significant and can also be used as a separation criterion.
Image analysis is used to quantitatively characterise the ISO 4505-1978 standard charts with respect to volume fraction, number density and size distribution of defects. The results are compared to measured distributions for true microstructures. 相似文献