Topological measurement of deep neural networks using persistent homology

Annals of Mathematics and Artificial Intelligence - The inner representation of deep neural networks (DNNs) is indecipherable, which makes it difficult to tune DNN models, control their training...     

Electrical Breakdown Properties and Space Charge Formation in High Temperature Region in Ultraviolet Ray Irradiated PVC

Polyvinyl chloride (PVC) is the most popular insulating material for electric wiring instruments. However, an exothermic reaction above 150 °C may cause deterioration of the insulating properties of PVC. Therefore, it is important to clarify the heat degradation in PVC, not only to investigate the ignition of electrical wiring products but also to use electrical products safely. It is known that ultraviolet (UV) irradiation causes chemical deterioration of PVC and an increase in its conductivity. Generally, it has been thought that the electrical breakdown properties, electrical conduction, and insulating performance are affected by space charge accumulation in an insulating material. A high temperature pulsed electroacoustic (PEA) system usable up to 250 °C has been developed, and the PEA system can measure the space charge distribution and conduction current in the high temperature range simultaneously. In this investigation, the space charge distribution and conduction current were measured up to electrical breakdown in a non‐UV irradiated sample (normal PVC) and in 353 nm and 253 nm UV‐irradiated PVC samples in the range from room temperature to 200 °C in a DC electric field. In the short wavelength UV irradiated PVC sample (253 nm, 300 h), a deterioration of breakdown strength at 90 °C to 150 °C and negative packet‐like charges were observed at 60 °C and 100 °C, a positive charge accumulated in front of both the anode and cathode above 90 °C, and a higher electric field near the cathode side because the positive charge of the cathode side was greater.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.     

Development of a fast neutron radiography converter using wavelength-shifting fibers

A fluorescent converter for fast neutron radiography (FNR) comprising a scintillator and hydrogen-rich resin has been developed and applied to electronic imaging. The rate of the reaction between fast neutrons and the converter is increased by thickening the converter, but its opaqueness attenuates emitted light photons before they reach its surface. To improve the luminosity of a fluorescent converter for FNR, a novel type of converter was designed in which wavelength-shifting fibers were adopted to transport radiated light to the observation end face. The performance of the converter was compared with that of a polypropylene-based fluorescent converter in an experiment conducted at the fast-neutron-source reactor YAYOI in the University of Tokyo.     

IMPINGING JET DRYER

In coating and gravure printing, an impinging jet nozzle with high thermal efficiency for drying of coated film was developed.

Trial production 0f 40 kinds of nozzle enables to develop a high-performance impinging jet nozzle with heat transfer coefficient 1.5 times larger than that of current slit nozzle, through measurement of heat transfer coefficient, visualizations of air flow and heat transfer, and measuremenu of jet velocity and turbulence distribution. The purpose of the trial production was to expand a range of high heat transfer and promote turbulence compared with the current nozzle.

Paying attention to mass transfer within gravure ink coated film, drying characteristic of the film was analyzed by numerical solution of a set of equations governing the drying process in which concentration dependencies 0f the diffusion coefficient and the equilibrium vapor pressure were considered.

Applying these analyses. an industrial scale dryer with excellent drying efficiency has finally been developed.     

Hydrodynamics of Superfluid Bose Gases in an Optical Lattice at Finite Temperatures

Starting from an effective action for the order parameter field, we derive a coupled set of generalized hydrodynamic equations for a Bose condensate in an optical lattice at finite temperatures. Using the linearized hydrodynamic equations, we study the microscopic mechanism of the Landau instability due to the collisional damping process between the condensate and noncondensate atoms. It is shown that the Landau criterion for the stability of a superfluid in a uniform system is modified due to the presence of the periodic optical lattice potential.     

Handling of fine-particles by time-averaged particle driving method in plasmas

We developed a noble technique for the fine-particle handling in plasmas. In this method a pair of point electrodes are introduced in the plasma, to which positive pulses are applied alternatively. When the pulse repetition period is shorter than the particle response time, the particles feel only time-averaged force because of their large mass. Spatial profile of the equivalent potential of the time-averaged force varies from a circle to an ellipse with an increase in the local discharge at the electrodes. The particles are eventually transported toward a middle point between two point-electrodes, being almost independent of their initial positions. This method is quite effective for converging fine particles in the plasma.     

Analysis of ink flow in a mimeograph printer based on the mechanics of fluid-filled poroelastic solids

Summary To understand some main ink flow mechanisms in a mimeograph printer, the continuum mechanics theory of fluid-saturated porous solids is applied to analyze the ink flow through screens and a printing master, which are modeled by a fluid-filled poroelastic single layer. The layer is assumed to be pressed by a press roller from below and to be subjected from above to the hydrodynamic lubrication pressure induced between a printing drum and an ink roller. Nonlinear elasticity of the layer and dependence of the permeability on its deformation are taken into account. The numerical results show some important results: e.g., squeezing-out of the ink from the layer by the layer compaction by the press roller plays an important role, especially for the case where the compression duration is small in comparison with the characteristic time of the ink-filled poroelastic layer.