Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

Adhesion of streptococci to saliva-coated and uncoated composite-based resins

This study was designed to evaluate the bacterial adhesion to five types of experimental composite-based resins and a commercial composite resin used as a control. Physicochemical surface characteristics of composite resins with and without an artificial saliva coating were measured. The relationship between the numbers of adhering cells (Streptococcus sanguis, S. mutans and S. sobrinus) and surface characteristics was analysed. The values of contact angles and the number of adhering cells were small with saliva coating. S. sanguis ATCC 10557 showed a positive correlation (r=0.835, p<0.05) with the contact angles of uncoated resins, whereas no relationship was observed for saliva-coated resins. With S. mutans Ingbritt the cell numbers adhering to resins correlated strongly (p<0.01) with the values of zeta potential of resins for either saliva coated or uncoated. Electrical repulsion forces had a strong contribution to adherence of cells such as S. mutans and S. sobrinus which show a high absolute zeta potential.     

Graphite formation on Ni film by chemical vapor deposition

Thin film formation of graphite by chemical vapor deposition using 2-methyl-1,2′-naphthyl ketone as a starting material was carried out on Ni film substrates. On Ni films directly deposited on quartz glass, the graphite films were obtained when the Ni film thickness was above 1 000 Å and above 5 000 Å at 700 °C and 1 000 °C, respectively. Depositions on thinner Ni film substrates comprise amorphous carbon (a-C) or graphite tubes which was owing to the thermal coagulation of the Ni film into droplets. On the other hand, graphite film was obtained on the Ni film with thickness 10 Å when a-C was inserted between the Ni film and the quartz glass. The coagulation of the Ni film is considered to be avoided by inserting a-C layer.     

Permeation of Zidovudine and Probenecid from Oily Bases Containing Alcohols Through Rat Skin

Permeation of zidovudine (3'-azido-3'-deoxythymidine, AZT) and probenecid from oily bases containing an alcohol through rat skin was examined. Isopropyl myristate (IPM), as an oily vehicle, showed a penetration enhancing effect for AZT and probenecid. Ethanol, n-propanol, and n-butanol were used as additives in IPM and were examined for their own permeation and the enhancing effect on the permeation of AZT and probenecid. The skin permeation of AZT and probenecid from IPM was enhanced by addition of the alcohol in IPM. The degree of the enhancement was decreased with increasing lipophilicity of the alcohol used. me permeation rate of the drug from those systems was shown to be governed by penetration-enhancing effects of the oily base and alcohol, and the penetration of the alcohol itself through the skin.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

A study of suppression of vapor explosions by adding inversely soluble polymers

The mechanism of the suppression of vapor explosions by adding inversely soluble polymers in water is studied. Vapor explosion experiments and quench experiment are conducted using a silver test piece. Polymetric solution (polyethylene oxide), of concentrations from 0 to 500 wppm, whose normalized viscosity (by water) varies from 1.00 to 2.00, is used. No vapor explosion is observed in the aqueous polymer solution at a concentration higher than 200 wppm. Quench experiments using the silver test piece submerged in the polymer solution and water are performed in order to examine the stability of film boiling. The suppression of the vapor film collapse is attributed to the precipitation of polyethylene as a gel around the vapor film. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(4): 297–306, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10037     

Latest advances in camcorder technology

Camcorders have been developed to be compact with high performance. Latest advancement of key technologies and devices such as digital signal processing LSI, six-layer printed circuit board with micro chips, high-speed power lens with linear motor, 103 K pixels 0.7-in LCD electronic viewfinder, and high-energy Li-ion battery are described. High-band format is also explained     

Virtualized Reality: Perspectives on 4D Digitization of Dynamic Events

Digitally recording dynamic events, such as sporting events, for experiencing in a spatio-temporally distant and arbitrary setting requires 4D capture: three dimensions for their geometry and appearance over the fourth dimension of time. Today's computer vision techniques make 4D capture possible. The virtualized reality system serves as an example on the general problem of digitizing dynamic events. In this article, we present the virtualized reality system's details from a historical perspective