Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Correlation between motion of source bender element and feedback signal induced by self-monitoring

Since the introduction of bender element tests to soil testing, the reliability of the estimated travel time has been the most serious problem. The author has previously shown a potential solution whereby removing the response of the bender element subsystem from the whole response could dramatically improve the accuracy of the travel time estimation. In order to lay the foundation for estimating the response of the bender element subsystem, this paper examines the correlation between the displacements of the element and the induced feedback signals by employing a self-monitoring element. The response of the self-monitoring element is modeled as a transfer function involving two internal transfer functions that relate the input signals to the displacements and the displacements to the feedback signals, respectively. Using a laser displacement sensor, the displacements are directly measured through the entire surface and reveal the three-dimensional bending motion of the element oscillating in both longitudinal and width directions. The feedback signals are similar to, but inconsistent with, the tip displacements, and an attempt is made to correct the feedback signals. Finally, a conclusion is given on the potential for estimating the response of the bender element subsystem using the self-monitoring element.     

Optical circulator consisting of a YIG spherical lens, PANDA-fibre polarisers and a fibre-optic polarising beam splitter

A novel optical circulator is reported which employs an yttrium-iron-garnet (YIG) sphere, PANDA-fibre polarisers and a fibre-optic polarising beam splitter. The splitting ratios of the fibre-optic polarising beam splitter were 1.0:99.0 for x-polarisation and 97.5:2.5 for y-polarisation, with an excess loss of 0.5 dB at 1.30 ?m wavelength. The backward isolation of the optical circulator was 30 dB with the total insertion loss of 4.5 dB.     

Linearity stablized fiber-optic thermometer using pseudo-heterodyne phase detection

A temperature sensor using a fiber-optic Fabry-Perot interferometer is described. A pseudo-heterodyne detection scheme is adopted to read the light phase difference in the Fabry-Perot interference output. A higher harmonic components comparison method is used to stabilize the system and to increase detection linearity. This system realizes not only highly sensitive temperature sensing with good linearity and minimal adjusting error, but also application to the sensing of other physical quantities such as vibrations. Additionally, the signal-to-noise ratio and distortion of the detected signal are investigated as functions of fiber end reflectivity. These results will be useful in designing a high performance fiber-optic Fabry-Perot thermometer.     

Clinical and serological study of tsutsugamushi disease in northern Osumi, Kagoshima Prefecture

We report 34 cases of tsutsugamushi disease seen from 1989 to 1993 at Yagi Clinic, northern Osumi, Kagoshima Prefecture. Nineteen patients (55.9%) showed the highest antibody titers against the Kawasaki strain Orientia tsutsugamushi (Ot) and 13 (38.2%) against the Kuroki strain Ot. It is suggested that two antigenic types (Kawasaki and Kuroki) of Ot were distributed in Kagoshima Prefecture, and the Kawasaki type Ot more or less dominates Kuroki type Ot. There was no difference in clinical features between the two groups of patients.     

Right atrial contractile performance in patients with myocardial infarction

To evaluate right atrial (RA) contractile performance in patients with myocardial infarction, we validated a cineangiographic method of RA volume measurement, and investigated RA volume change in 'normal' individuals and patients with a previous myocardial infarction. Sixteen silicone rubber RA casts made from human cadavers were filmed in the postero-anterior and left lateral projections. The cast volumes calculated following Simpson's rule were in good agreement with those measured by water replacement (r = 0.992, P < 0.01). At cardiac catheterization, biplane RA cineangiography was performed in 19 'normal' individuals (N group), in 14 patients with a previous antero-septal infarction (AMI group) and in seven patients with a previous inferior infarction (IMI group). The RA volume-time curve was constructed at 20-40 ms intervals for one cardiac cycle. RA volume at the beginning of the atrial contraction (RAVd), which was defined as the 'preload' of the RA, tended to be larger in both the AMI and IMI groups compared with 'normal' individuals. The RA ejection volume was significantly larger in both the AMI (18.4 +/- 2.1 ml.m-2, P < 0.01) and IMI groups (19.4 +/- 2.8, P < 0.01) than in the N group (14.5 +/- 1.9), even for a comparable level of RAVd (range from 26 to 36 ml.m-2) (18.6 +/- 2.1, P < 0.01, 18.2 +/- 2.0, P < 0.01, 14.7 +/- 1.9, respectively). These results suggest that RA contraction increases in patients with myocardial infarction by increasing both the 'preload' and 'contractility' of the RA.     

A 0.1-μm delta-doped MOSFET fabricated with post-low-energyimplanting selective epitaxy

A simple fabrication technology for delta-doped MOSFETs, named post-low-energy implanting selective epitaxy (PLISE) is presented. The PLISE technology needs no additional photo-lithography mask, deposition step or etching step even for CMOS devices. The only additional step is growing undoped epitaxial channel layers by UHV-CVD after the channel implantation. With this technology, delta-doped NMOSFETs with 0.1-μm gate length were successfully fabricated. By optimizing the epi-layer thickness and the channel doping level, short-channel effects are suppressed enough to achieve 0.1-μm gate length. Moreover, the junction capacitance at zero bias is reduced by 50%     

二垩英与资源回收-Ⅰ考虑到二垩英生成的资源与能量回收基础研究

目前在日本,存在大量工业垃圾,包括各种塑料制品,ASR(汽车破碎垃圾),含有毒PCB(多氯联苯)的110变压器和PVC(聚氯乙稀)制品等.而来自城市垃圾焚烧炉的废气含有大量能量.因此,在充分考虑环境、避免二垩英生成的同时,安全回收来自工业垃圾、城市和/或工业垃圾焚烧炉的资源和能量是个非常重要的课题,这也将对抑制CO2排放作出贡献.正确地阐明焚烧过程中二垩英的生成机理及详细研究含少量二垩英的焚烧废气在冷却过程中大量形成二垩英的临界温度是项很重要的工作.解决这个问题可有效实现资源和能量的回收.本报告介绍日本在二垩英排放方面目前采取的对策和存在的问题以及大阪大学为阻止二垩英生成所做的基础研究工作.