Chronic hypertrophic gastropathy in a child resembling adult Menetrier''s disease

N-(phosphonacetyl)-disodium L-aspartic acid (PALA) demonstrates a synergistic antitumor effect when combined with 5-Fluorouracil (5-FU) in in vitro studies. In a Phase II trial, 23 eligible patients with unresectable or metastatic adenocarcinoma of the stomach were treated with weekly i.v. bolus PALA (250 mg/M2) followed 24 hours later by a 24-hour infusion of 5-FU (2600 mg/M2) for an initial period of 8 weeks. No objective responses were noted. PALA and 5-FU is inactive against gastric adenocarcinoma at the doses and schedule used in this trial.     

Optical properties and laser performance of neodymium doped fluoroapatites SrxCa5−x(PO4)3F (x = 0, 1, 2, 3, 4, and 5)

Nd doped fluoroapatites Sr_xCa_5−x(PO₄)₃F(S_xC_5−xPF, X = 0, 1, 2, 3, 4, and 5) single crystals have been grown by the Czochralski technique. Their polarized absorption and emission spectra have been recorded at room temperature and used to calculate the absorption and stimulated emission cross sections. Broadening of the absorption and emission bands is observed for Nd³⁺ in the solid solutions SPF-CPF compared to Nd³⁺ in CPF or SPF. 1% Nd:S_xC_5−xPF, X = 0, 2, 3, 4, and 5, laser rods have been tested in a cavity longitudinally pumped by a 1 W AlGaAs laser diode and compared to Nd:YAG and Nd:YVO₄ rods. All fluoroapatites exhibit very good laser performance with low thresholds and high slope efficiencies, higher than in the case of YAG and equal to the YVO₄ samples. The dependance of the laser output power versus the diode temperature has also been measured for all materials. The laser output was found to be as sensitive to the diode temperature fluctuations for fluoroapatites as for YAG.     

Une architecture massivement parallèle intégrée

This paper presents a new massively parallel MIMD architecture, halfway between the Connection Machine and hypercubes based on 32-bit processors. It is built from specific 8-bit processors arranged in a 2-D grid and communicating by message transfers. We discuss the communication problems, the instruction set of the basic processing unit, the programmation of the whole array and the use of a high level data-flow language.     

The influence of demineralisation and ammoxidation on the adsorption properties of an activated carbon prepared from a Polish lignite

The preparation of cheap nitrogen-enriched materials with large adsorptive capacities and selectivity towards volatile organic compounds remains a challenge. Ammoxidation has been used to prepare nitrogen-enriched activated carbons using a demineralised Polish lignite. The lignite samples were demineralised by two different methods before nitrogen-enrichment by ammoxidation and physical activation in steam. The surface chemistry was investigated by elemental analysis, Boehm titration, infrared and XPS spectroscopies and adsorptive properties by a linear solvation energy relationship approach. Results show a quasi-total demineralisation and a higher reactivity towards nitrogen for the demineralised samples. The BET surface is also higher than for the non-demineralised lignite. Active carbons previously ammoxidated and demineralised are more interesting in terms of selective removal of gaseous pollutants.     

Tangential cover for thick digital curves

The recognition of digital shapes is a deeply studied problem. The arithmetical framework, initiated by Reveillès [Géométrie discrète, calcul en nombres entiers et algorithmique, Thèse d’Etat, 1991], provides a powerful theoretical basis, as well as many algorithms to deal with digital objects. The tangential cover, first presented in Feschet and Tougne [Optimal time computation of the tangent of a discrete curve: application to the curvature, in: G. Bertrand, M. Couprie, L. Perroton (Eds.), 8th Discrete Geometry for Computer Imagery, Lecture Notes in Computer Science, vol. 1568, Springer, Berlin, 1999, pp. 31-40] and Feschet [Canonical representations of discrete curves, Pattern Anal. Appl. 8(1-2) (2005) 84-94] is a useful tool for representing geometric digital primitives. It computes the set of all maximal segments of a digital curve and permits either to obtain minimal length polygonalization or asymptotic convergence of tangents estimations. Nevertheless, the arithmetical approach does not tolerate the introduction of irregularities, which are however inherent to the acquisition of digital shapes. The present paper is an extension of Faure and Feschet [Tangential cover for thick digital curves, in: D. Coeurjolly, I. Sivignon, L. Tougne, F. Dupont (Eds.), DGCI 2008, Lecture Notes in Computer Science, vol. 4992, Springer, Berlin, 2008, pp. 358-369], in which we propose a new definition for a class of the so-called “thick digital curves” that applies well to a large class of digital object boundaries. We then propose an extension of the tangential cover to thick digital curves and provide an algorithm with an O(nlogn) time complexity, where n denotes the number of points of specific subparts of the thick digital curve. In order to keep up with this low complexity, some critical points must be taken into account. We describe all required implementation details in this paper.     

Synthesis and characterization of WO3 thin films by surfactant assisted spray pyrolysis for electrochromic applications

Thin films of WO₃ were prepared by surfactant assisted spray pyrolysis on F-doped SnO₂ (FTO) conductive glass by using hexadecyltrimethylammonium bromide (HTAB) and polyethylene glycol (PEG400):HTAB as growth controlling agents. The surface tension of the spraying solutions was experimentally evaluated and was correlated with the deposition processes (nucleation and growth) of very smooth and homogenous films. The effect of the surfactant, alone and associated with PEG, on the structure (XRD), morphology (AFM), surface composition (XPS), FTIR and hydrophilicity (contact angle) were investigated and their influence on the electrochromic activity was discussed. Using surfactants and PEG, the coloration efficiency, transmission modulation and cycling stability of the WO₃ thin films can be enhanced.     

Alumina foam catalyst supports for industrial steam reforming processes

The manufacture and the characterisation of alumina foams as alternative catalysts supports for industrial steam reforming processes are presented here. The possibility of use of alumina foams as catalysts supports in such processes is evaluated by studying their resistance toward mechanical and chemical stresses. The alumina foams produced are characterised owing to their processing parameters (slurry infiltration, sintering temperature, template pore size). Their ability to work in hydrothermal atmosphere is assessed by characterising the evolution of microstructures and mechanical strengths upon aging. Thermodynamic studies of the stability of alumina in industrial steam reforming working conditions are performed and correlated to the experiments to demonstrate the stability of such a system.     

Collision Detection for Deformable Objects

Interactive environments for dynamically deforming objects play an important role in surgery simulation and entertainment technology. These environments require fast deformable models and very efficient collision handling techniques. While collision detection for rigid bodies is well investigated, collision detection for deformable objects introduces additional challenging problems. This paper focuses on these aspects and summarizes recent research in the area of deformable collision detection. Various approaches based on bounding volume hierarchies, distance fields and spatial partitioning are discussed. In addition, image‐space techniques and stochastic methods are considered. Applications in cloth modeling and surgical simulation are presented.     

Postoperative outcome of Crohn's disease in 30 children

BACKGROUND: Thirty children operated on for Crohn's disease (CD) were reviewed (1975-1994). The aim of the study was to assess their postoperative outcome. PATIENTS: 19 boys and 11 girls, aged 15.3 (2) years (range 11.3-20) at surgery were studied. RESULTS: Surgical indications were acute complications of CD and chronic intestinal illness. Six months after surgery, 11 of 12 patients had been weaned off steroids, and 22 of 23 patients were weaned off nutritional support; 17 patients without recurrence had a mean (SD) weight gain of 2.1 (8) kg and a height gain of 3.36 (3) cm. During 3.1 (2.7) years follow up, 12 patients (40%) had a recurrence of the disease after 19.4 (14) months (means (SD)): supra-anastomotic recurrence (six), severe perianal disease (two), and chronic illness (four). Six of 14 patients who were treated with mesalazine (13) or azathioprine (one) had recurrences. The postoperative recurrence rate was 50% at two years. CONCLUSION: Surgical treatment modifies the immediate outcome of severe or complicated CD, but does not prevent recurrence, despite localised resection or prophylactic postoperative treatment. Extension of the disease before surgery seems to be a major risk factor for postoperative recurrence in children.     

An intestinal surgery simulator: real-time collision processing and visualization

This research work is aimed toward the development of a VR-based trainer for colon cancer removal. It enables the surgeons to interactively view and manipulate the concerned virtual organs as during a real surgery. First, we present a method for animating the small intestine and the mesentery (the tissue that connects it to the main vessels) in real-time, thus enabling user interaction through virtual surgical tools during the simulation. We present a stochastic approach for fast collision detection in highly deformable, self-colliding objects. A simple and efficient response to collisions is also introduced in order to reduce the overall animation complexity. Second, we describe a new method based on generalized cylinders for fast rendering of the intestine. An efficient curvature detection method, along with an adaptive sampling algorithm, is presented. This approach, while providing improved tessellation without the classical self-intersection problem, also allows for high-performance rendering thanks to the new 3D skinning feature available in recent GPUs. The rendering algorithm is also designed to ensure a guaranteed frame rate. Finally, we present the quantitative results of the simulations and describe the qualitative feedback obtained from the surgeons.