Changes in Lake Ontario Total Phosphorus Concentrations 1976–1978

An apparent decrease in total phosphorus concentrations of approximately 4.l μgP/L has been reported recently for the spring values of 1977 and 1978 in Lake Ontario. Investigation of the loading reduction for this period independent of sedimentation factors can account for only 10% of the change. The results indicate that changes in the sedimentation rate of total phosphorus during this period offer an explanation for the majority of the change in concentration.     

Epoxy paint failure in B-52 fuel tanks: Part II. Influence of DIEGME concentration in the fuel on the failure process

A model has been proposed to explain the failure of the original BMS10-39 epoxy paint on upper vertical surfaces in B-52 fuel tanks. The model involves interaction of the paint with DIEGME, a fuel system ice inhibitor (FSII) in jet fuel, that is distilled from the liquid fuel. In this communication, distillation experiments used to support the model are refined to better match the mass transfer of vapor from fuel in a B-52 fuel tank at close to room temperature. The interaction of these lower temperature distillates with the paint affirms the earlier model. On the basis of these experiments it is proposed that paint failure may be controlled or eliminated by reducing the level of DIEGME in the fuel. Proposed changes in military jet fuel composition are detailed.     

Interval based MINLP superstructure synthesis of mass exchange networks

A new simultaneous synthesis approach for mass exchange networks (MENs) is presented. The technique is adapted from the interval based mixed integer non-linear program (MINLP) superstructure (IBMS) synthesis of heat exchanger networks (HENs). The superstructure interval boundary compositions are defined by the supply and target compositions of either the rich or lean set of streams. Each rich and lean stream in the superstructure has the potential of exchanging mass with streams of opposite kind in each interval based on mass transfer feasibility. The model harnesses the strengths of the stagewise superstructure and the pinch technology methods for mass exchange network synthesis (MENS). The IBMS approach simultaneously trades-off the capital and operating costs for MENs. The superstructure composition interval defining approach introduced in this paper enforces the mixing of split streams at equal compositions, hence there is no need to include mixing equations in the model. Fixing the interval boundaries helps to eliminate the complexities involved in initialisations, thus the region of search for the optimum solution is reduced. The IBMS model is applied to MENS problems involving continuous contact and staged columns. It is also extended to problems involving multiple mass separating agents (MSAs) and regeneration. The results obtained compare well with those in the literature.     

The role of benchmarking for yardstick competition

With the increasing interest in yardstick regulation, there is a need to understand the most appropriate method for realigning tariffs at the outset. Benchmarking is the tool used for such realignment and is therefore a necessary first-step in the implementation of yardstick competition. A number of concerns have been raised about the application of benchmarking, making some practitioners reluctant to move towards yardstick based regimes. We assess five of the key concerns often discussed and find that, in general, these are not as great as perceived. The assessment is based on economic principles and experiences with applying benchmarking to regulated sectors, e.g. in the electricity and water industries in the UK, The Netherlands, Austria and Germany in recent years. The aim is to demonstrate that clarity on the role of benchmarking reduces the concern about its application in different regulatory regimes. We find that benchmarking can be used in regulatory settlements, although the range of possible benchmarking approaches that are appropriate will be small for any individual regulatory question. Benchmarking is feasible as total cost measures and environmental factors are better defined in practice than is commonly appreciated and collusion is unlikely to occur in environments with more than 2 or 3 firms (where shareholders have a role in monitoring and rewarding performance). Furthermore, any concern about companies under-recovering costs is a matter to be determined through the regulatory settlement and does not affect the case for using benchmarking as part of that settlement.     

Cost-effectiveness of preoperative localization studies in primary hyperparathyroid disease

OBJECTIVE: To evaluate the effect of preoperative localization studies on the surgical management of patients with primary hyperparathyroid disease (PHPT). SUMMARY BACKGROUND DATA: Reported cure rates of initial surgical exploration for PHPT are close to 95%. Preoperative localization studies are frequently obtained to improve surgical success and decrease operative time. METHODS: Initial cervical exploration was performed in 113 patients with PHPT from 1981 to 1993. Twenty-four patients (21%) had surgery without preoperative localization studies. The remaining 89 patients (79%) had 132 noninvasive preoperative localization studies. Success of the localization studies in tumor localization, pathologic findings, postoperative serum calcium levels, and operative times were compared. Patient costs of the studies were calculated. RESULTS: Disease was identified during operation in 23 of 24 patients (96%) having cervical exploration without preoperative localization studies, and they had normal calcium levels after surgery. Eighty-seven of 89 patients (98%) having preoperative localization studies were surgically cured. The highest sensitivity rate (60%) and highest positive predictive value (79%) of the localization studies were found with thallium-technetium scintiscanning. Average cost of the localization studies was $901 per patient. Combination studies were obtained in 32 patients at an average cost of $1,314 per patient without improving sensitivity. Mean operating time did not differ for localized and nonlocalized patients. CONCLUSIONS: Preoperative localization studies did not improve parathyroid localization or cure rate and did not substantially shorten operating time in initial cervical exploration for PHPT. The economic burden of routine preoperative localization studies in these patients is not justified.     

Heterochromatin effects on the frequency and duration of LCR-mediated gene transcription

Organ transplantation is associated with an early bone loss that subsequently increases the risk of osteopenia and bone fractures. It is not known whether bone loss continues in long-term survivors, but persistent bone demineralization could further jeopardize an already diminished bone mass. To better define long-term bone status of kidney transplant recipients (KTR), we conducted cross-sectional and longitudinal evaluations of bone mineral density (BMD) in 70 KTR with a mean posttransplantation time of 8.1 years. BMD was determined by dual-energy X-ray absorptiometry and was repeated in 55 of the patients after a mean follow-up period of 22 +/- 5 months. Lumbar and femoral osteopenia, defined as a BMD lower than 2 standard deviations from mean value of sex- and age-matched controls, was present in 28.6% and 10.5% of patients, respectively. There was a significant negative correlation between cumulative prednisone dose and adjusted lumbar as well as femoral BMD (R = 0.45, P < 0.001 and R = 0.29, P < 0.05, respectively). Five patients had a vertebral BMD below a fracture threshold of 0.777 g/cm2. Vertebral fractures (VF) were found in four men and were associated with higher prednisone dosage (P < 0.05), larger cumulative prednisone dose (P < 0.05), and significantly lower BMD values. According to World Health Organization recent criteria for women, prevalences of lumbar and femoral osteopenia and lumbar and femoral osteoporosis in female patients reach 75%, 65%, 33%, and 10%, respectively. The longitudinal part of the study showed a persistent pathological lumbar demineralization process. Over the study period, BMD, expressed as a percentage of that of controls, decreased from 89 +/- 14% to 86 +/- 14% (P < 0.001). Annual change of bone mass was -1.7 +/- 2.8% per year. Accelerated vertebral bone loss (defined as a decrease of BMD, expressed as a percentage of that of controls, of more than 1% per year) was present in 56% of patients and was associated with higher prednisone dosage (P < 0.01). In conclusion, although VF are relatively infrequent in long-term survivors of renal transplantation, osteopenia is a frequent finding, and a substantial proportion of women present lumbar osteoporosis. An ongoing demineralization process of the spine is also demonstrated and probably contributes to long-term spinal osteoporosis incidence. Prednisone dosage remains the most constantly isolated risk factor.     

Inertia-friction welding of SiC-reinforced 8009 aluminium

Inertia-drive friction welding (IFRW) of an 8009 Al alloy (Al-8.5 Fe-1.7 Si-1.3 V, wt%) reinforced with 11 volume per cent SiC particles (8009/SiC/11_p) has been investigated. Inertia-drive friction welds were made with constant energy at two levels of axial force. The microstructures of the base material and the welds were characterized using optical and scanning electron microscopy, while the mechanical properties were evaluated using microhardness and tensile testing. Examination of weld sections revealed that the hot deformation experienced during welding produced a homogenized microstructure with a uniform distribution of SiC particles along the bond line. No evidence of a chemical reaction between the SiC and the matrix was found in any of the welds, but cracking of some of the larger SiC particles was observed in the base material as well as in the IFR welds. The average microhardness of the various heat-and-deformation affected zones (HDZs) of the welds did not vary greatly from that of the base material, and no weld induced weak regions were discerned. The room-temperature (RT) tensile strength of the IFR welds exceeded 90 per cent of the base material. The weld tensile specimens failed at the outer edge of the HDZ for all of the welds tested. The fracture surface of the 8009 matrix of tensile samples for both the base material and the welds exhibited a dimpled appearance indicating a ductile failure, while fracture through the SiC appeared to occur in a brittle fashion. IFRW has proven effective in joining 8009/SiC/11_p with little loss in RT hardness and tensile properties.     

A study of the effects of the location of flashing inception on maximum and minimum critical two-phase flow rates:: Part II: analysis and modelling

A general unified model is developed to predict one-component critical two-phase pipe flow. An extension of the Henry [Henry, R.E., 1970. The Two-Phase Critical Discharge of Initially Saturated or Subcooled Liquid. Nucl. Sci. Eng. 41, 336-342.] and Henry and Fauske [Henry, R.E., Fauske, H.K., 1970. The two-Phase critical Flow of One-Component Mixtures in Nozzles; Orifices and Short Tubes, ASME J. Heat Transfer, May 1970.] models to incorporate the effects of wall friction and the location of flashing inception is proposed. Modelling of the two-phase flow is accomplished by describing the evolution of the flow between the location of flashing inception and the exit (critical) plane. The model approximates the nonequilibrium phase change process via thermodynamic equilibrium paths. Included are the relative effects of varying the location of flashing inception, pipe geometry, fluid properties and length to diameter ratio. The model predicts that a range of critical mass fluxes exist and is bound by a maximum and minimum value for a given thermodynamic state. This range is more pronounced at lower subcooled stagnation states and can be attributed to the variation in the location of flashing inception. The model is based on the experimental study of critical two-phase flow rates of saturated and subcooled water through long tubes given in Part I of this work. In that study, the location of flashing inception was accurately controlled and adjusted through the use of a new device. The data obtained revealed that for fixed stagnation conditions, the maximum critical mass fluxes occurred with flashing inception located near the pipe exit; while minimum critical mass fluxes occurred with the flashing front located further upstream. The results of the present study, as well as available data since 1970 are compared with the model predictions. These data cover a wide range of conditions and include test section L/D ratios from 25 to 302 and a temperature and pressure range of 110-280°C and 0.16-6.9 Mpa, respectively. The predicted maximum and minimum critical mass fluxes show an excellent agreement with the range observed in the experimental data.