Uncertainties in the determination of pyrrolizidine alkaloid levels in naturally contaminated honeys and comparison of results obtained by different analytical approaches

The contamination of honey with hepatotoxic pyrrolizidine alkaloids (PAs) is a well-known hazard for food safety. While management strategies and controls of the honey industry aim to reduce the PA levels, uncertainties remain with regard to the safety of regionally produced and marketed honey. In addition, a previous study showed large differences of results obtained after various periods of storage and apparent differences between the analytical results of different laboratories. Therefore, this study aimed at examining these uncertainties by monitoring the impact of storage on the PA and PA N-oxide (PANO) content of two freshly harvested honeys and on possible demixing effects caused by pollen settling. Additionally, three analytical approaches – target analysis with matrix-matched calibration or standard addition and a sum parameter method – were applied for a comparative analysis of 20 honeys harvested in summer 2016. All samples originated from Schleswig-Holstein in Northern Germany where the PA plant Jacobaea vulgaris is currently observed on a massive scale. The results of the time series analyses showed that PANO levels markedly decreased within a few weeks and practically reached the LOD 16 weeks after harvest. Tertiary PAs, by contrast, remained stable and did not increase as a consequence of PANO decrease. The experiments on a putative demixing, which may result in a heterogeneous distribution of PAs/PANOs, revealed that there was no such effect during storage of up to 12 weeks. A comparison of the PA/PANO levels obtained by different analytical approaches showed that in some cases the sum parameter method yielded much higher levels than the target approaches, whereas in other cases, the target analysis with standard addition found higher levels than the other two methods. In summary, the results of this study highlight uncertainties regarding the validity and comparability of analytical results and consequently regarding health risk assessment.     

Mixed Mode VLSI Implementation of a Neural Associative Memory

A mixed mode digital/analog special purpose VLSI hardware implementation of an associative memory with neural architecture is presented. The memory concept is based on a matrix architecture with binary storage elements holding the connection weights. To enhance the processing speed analog circuit techniques are applied to implement the algorithm for the association. To keep the memory density as high as possible two design strategies are considered. First, the number of transistors per storage element is kept to a minimum. In this paper a circuit technique that uses a single 6-transistor cell for weight storage and analog signal processing is proposed. Second, the device precision has been chosen to a moderate level to save area as much as possible. Since device mismatch limits the performance of analog circuits, the impact of device precision on the circuit performance is explicitly discussed. It is shown that the device precision limits the number of rows activated in parallel. Since the input vector as well as the output vector are considered to be sparsely coded it is concluded, that even for large matrices the proposed circuit technique is appropriate and ultra large scale integration with a large number of connection weights is feasible.     

Sequential Decoding of Convolutional Codes for Rayleigh Fading Channels

The performance of sequential decoding of long constraint length convolutional codes is evaluated for Rayleigh fading channels. Sequential decoding is not practical below a certain theoretical signal-to-noise ratio, and these theoretical limits are calculated for a number of modulation methods and code rates. As an example, with BPSK modulation, soft decisions and code rate 1/2, the theoretical signal-to-noise ratio per information bit is 5.7 dB. Above this limit the bit error rate can be made arbitrarily small by increasing the constraint length at no significant complexity cost. Furthermore, it is shown that with carefully chosen quantization steps, 8 level uniform quantization gives a negligible loss also for sequential decoding on a Rayleigh fading channel. Simulation results using 8 level quantization correspond well with the theoretical performance bounds. Also, the performance on a correlated channel with finite interleaving has been obtained. With an interleaver depth of 50×50 and a normalized doppler frequency equal to 0.01 we are only 0.5 dB away from the performance with perfect interleaving. Finally, bit error rate results show this scheme to compete well with Turbo codes.     

Analysis of viscoelastic laminated composite plates

A micromechanics analysis is performed for the determination of the five independent elastic moduli of unidirectional fiber composites. By considering viscoelastic phases and by using the correspondence principle and the inversion of the Laplace transform, the five time-dependent functions which characterize the effective behavior of viscoelastic composites are established. The predicted time-dependent behavior is applied for the analysis of viscoelastic laminated plates. The resulting viscoelastic effects are shown, and comparison between the results obtained within the classical laminated plate theory and the first-order shear deformation theory is discussed.     

Synthesis of N,N-diethyl-N-{4-[(E)-(4-nitrophenyl)diazenyl]phenyl}amine via in situ diazotisation and coupling in supercritical carbon dioxide

The synthesis of azo dyes via a conventional aqueous-based diazotisation and coupling reaction requires the use of relatively high concentrations of mineral acids, which leads to high electrolyte concentrations in wastewater. Reported in this paper is an environmentally benign one-pot method for the synthesis of a nonionic azo dye, N,N -diethyl- N -{4-[( E )-(4-nitrophenyl)diazenyl]phenyl}amine, in supercritical carbon dioxide without using a mineral acid. The product yield increased significantly with temperature, with 91% theoretical yield afforded at 80 °C. The pressure of the system had little influence on product yield.     

Measurement of Gibbs energies of formation of CoF2 and MnF2 using a new composite dispersed solid electrolyte

Gibbs energies of formation of CoF₂ and MnF₂ have been measured in the temperature range from 700 to 1100 K using Al₂O₃-dispersed CaF₂ solid electrolyte and Ni+NiF₂ as the reference electrode. The dispersed solid electrolyte has higher conductivity than pure CaF₂ thus permitting accurate measurements at lower temperatures. However, to prevent reaction between Al₂O₃ in the solid electrolyte and NiF₂ (or CoF₂) at the electrode, the dispersed solid electrolyte was coated with pure CaF₂, thus creating a composite structure. The free energies of formation of CoF₂ and MnF₂ are (± 1700) J mol⁻¹; {fx37-1} The third law analysis gives the enthalpy of formation of solid CoF₂ as ΔH° (298·15 K) = −672·69 (± 0·1) kJ mol⁻¹, which compares with a value of −671·5 (± 4) kJ mol⁻¹ given in Janaf tables. For solid MnF₂, ΔH°(298·15 K) = − 854·97 (± 0·13) kJ mol⁻¹, which is significantly different from a value of −803·3 kJ mol⁻¹ given in the compilation by Barinet al.