Radiation tolerance for the SMASH-series front-end chips for a silicon micro-strip detector

The radiation tolerance for prototype front-end chips designed for a silicon micro-strip detector was examined with a ⁶⁰Co irradiation source to establish an allowable range of the radiation dose. The irradiated front-end chips were SMA²SH-64A, a 64-channel preamplifier array; SMA²SH-1, a single-channel preamplifier circuit with a comparator; and Control-C, a digital-control chip for the preamplifiers.     

The Atmospheric Scanning Electron Microscope with open sample space observes dynamic phenomena in liquid or gas

Although conventional electron microscopy (EM) requires samples to be in vacuum, most chemical and physical reactions occur in liquid or gas. The Atmospheric Scanning Electron Microscope (ASEM) can observe dynamic phenomena in liquid or gas under atmospheric pressure in real time. An electron-permeable window made of pressure-resistant 100 nm-thick silicon nitride (SiN) film, set into the bottom of the open ASEM sample dish, allows an electron beam to be projected from underneath the sample. A detector positioned below captures backscattered electrons. Using the ASEM, we observed the radiation-induced self-organization process of particles, as well as phenomena accompanying volume change, including evaporation-induced crystallization. Using the electrochemical ASEM dish, we observed tree-like electrochemical depositions on the cathode. In silver nitrate solution, we observed silver depositions near the cathode forming incidental internal voids. The heated ASEM dish allowed observation of patterns of contrast in melting and solidifying solder. Finally, to demonstrate its applicability for monitoring and control of industrial processes, silver paste and solder paste were examined at high throughput. High resolution, imaging speed, flexibility, adaptability, and ease of use facilitate the observation of previously difficult-to-image phenomena, and make the ASEM applicable to various fields.     

Phosphorus flame retardants in indoor dust and their relation to asthma and allergies of inhabitants

Organophosphate esters are used as additives in flame retardants and plasticizers, and they are ubiquitous in the indoor environment. Phosphorus flame retardants (PFRs) are present in residential dust, but few epidemiological studies have assessed their impact on human health. We measured the levels of 11 PFRs in indoor floor dust and multi‐surface dust in 182 single‐family dwellings in Japan. We evaluated their correlations with asthma and allergies of the inhabitants. Tris(2‐butoxyethyl) phosphate was detected in all samples (median value: 580 μg/g in floor dust, 111 μg/g in multi‐surface dust). Tris(2‐chloro‐iso‐propyl) phosphate (TCIPP) was detected at 8.69 μg/g in floor dust and 25.8 μg/g in multi‐surface dust. After adjustment for potential confounders, significant associations were found between the prevalence of atopic dermatitis and the presence of TCIPP and tris(1,3‐dichloro‐2‐propyl) phosphate in floor dust [per log₁₀‐unit, odds ratio (OR): 2.43 and 1.84, respectively]. Tributyl phosphate was significantly associated with the prevalence of asthma (OR: 2.85 in floor dust, 5.34 in multi‐surface dust) and allergic rhinitis (OR: 2.55 in multi‐surface dust). PFR levels in Japan were high compared with values reported previously for Europe, Asia‐Pacific, and the USA. Higher levels of PFRs in house dust were related to the inhabitants' health status.     

Topic allocation method on edge servers for latency-sensitive notification service

The importance of real-time notification has been growing for social services and Intelligent Transporting System (ITS). As an advanced version of Pub/Sub systems, publish-process-subscribe systems, where published messages are spooled and processed on edge servers, have been proposed to achieve data-driven intelligent notifications. In this paper, we present a system that allows a topic to be managed on multiple edge servers so that messages are processed near the publishers, even when publishers spread over a wide area. Duplicating messages on geographically distributed servers could enable immediate notification to neighboring subscribers. However, the duplicated message spool may cause exhaustion of resources. We prepare a formal model of our publish-process-subscribe system and formulate the topic allocation as an optimization problem under the resource constraints of edge servers. As the optimization problem is NP-hard, we propose heuristics leveraging the locality and the pub/sub relationships observed between clients to use the edge server resources efficiently. Our performance evaluation shows that our method reduces the delay to deliver notifications and the effectiveness of the strategy exploiting the relationships between clients.     

Effects of supercritical carbon dioxide treatment on the morphology of poly(l‐lactide)

Synthetic l ‐lactide random copolymers can be employed as controlled release materials when prepared using supercritical carbon dioxide (scCO₂), since they are biodegradable via hydrolysis. To determine the effects of thermal properties on polymer performance following scCO₂ processing, three types of poly(l ‐lactide) having different properties were assessed. The T_m of one poly(l ‐lactide) sample (H‐100) was found to be approximately 170 °C over the processing pressure range from 8 to 18 MPa, while a second sample (H‐440) also showed a constant value of approximately 152 °C. In contrast, the poly(l ‐lactide) REVODE exhibited a T_m of 146 °C prior to processing but a higher value of 147 °C following treatment at 8 MPa. Unlike the H‐100 and H‐440, the T_m value of the REVODE tended to decrease with increasing pressure. The T_g values increased greatly under mild conditions of 8 MPa pressure and a temperature of 40 °C. In particular, the T_g values for the H‐440 and REVODE increased by 4 °C and 5 °C, respectively. All T_g values were lowest at 12 MPa and increased with increasing processing pressure, although the effect of processing temperature was minimal. The Χ_{c DSC} of the H‐100 was 18% initially but increased to 20% upon scCO₂ processing at 40 °C and 14 MPa, and showed further increases at higher processing temperatures. Although the relationship between processing temperature and Χ_{c DSC} values for the H‐440 showed the same trend as observed with the H‐100, a different trend was seen for the REVODE. The Χ_{c XRD} values obtained from the XRD analyses differed from the values generated by DSC analysis, and showed a maximum degree of crystallinity following processing at 80 °C both with and without scCO₂ treatment. ATR FT‐IR analyses identified peaks due to semicrystalline regions in poly(l ‐lactide) samples treated with scCO₂, even when applying low temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44006.     

Elongation and Contraction of Scallop Sarcoplasmic Reticulum (SR): ATP Stabilizes Ca2+-ATPase Crystalline Array Elongation of SR Vesicles

The Ca²⁺-ATPase is an integral transmembrane Ca²⁺ pump of the sarcoplasmic reticulum (SR). Crystallization of the cytoplasmic surface ATPase molecules of isolated scallop SR vesicles was studied at various calcium concentrations by negative stain electron microscopy. In the absence of ATP, round SR vesicles displaying an assembly of small crystalline patches of ATPase molecules were observed at 18 µM [Ca²⁺]. These partly transformed into tightly elongated vesicles containing ATPase crystalline arrays at low [Ca²⁺] (≤1.3 µM). The arrays were classified as ‘’tetramer’’, “two-rail” (like a railroad) and ‘’monomer’’. Their crystallinity was low, and they were unstable. In the presence of ATP (5 mM) at a low [Ca²⁺] of ~0.002 µM, “two-rail” arrays of high crystallinity appeared more frequently in the tightly elongated vesicles and the distinct tetramer arrays disappeared. During prolonged (~2.5 h) incubation, ATP was consumed and tetramer arrays reappeared. A specific ATPase inhibitor, thapsigargin, prevented both crystal formation and vesicle elongation in the presence of ATP. Together with the second part of this study, these data suggest that the ATPase forms tetramer units and longer tetramer crystalline arrays to elongate SR vesicles, and that the arrays transform into more stable “two-rail” forms in the presence of ATP at low [Ca²⁺].     

Detail analysis of fusion neutronics benchmark experiment for iron

In order to specify the best nuclear data on iron, the fusion neutronics benchmark experiment on iron at Japan Atomic Energy Agency (JAEA)/Fusion Neutronics Source (FNS) was analyzed in detail with MCNP-4C and the latest nuclear data libraries, JENDL-3.3, FENDL-2.1, JEFF-3.1 and ENDF/B-VII.0. As a result, totally the calculation result with ENDF/B-VII.0 agreed with the measurement best, except that it underestimated the measured neutron flux above 10 MeV with the depth. It was noted that the calculation result with JENDL-3.3 overestimated the measured neutrons below a few keV. Through the DORT calculations based on the iron data in ENDF/B-VII.0, it was found out that the first inelastic scattering cross-section data of ⁵⁷Fe in JENDL-3.3 caused the overestimation.     

Thermoreversible behavior of κ-carrageenan and its apatite-forming ability in simulated body fluid

Osteoconductive materials with self-setting ability have received much attention because their properties allow developing injectable materials for bone defects. Thermosensitive hydrogel with ability of bone-like apatite formation in a body environment is a candidate of injectable bone fillers with osteoconductivity because the apatite formation on materials is an essential to show osteoconduction. The present study focused on the development of a thermosensitive hydrogel through modifications of the sulphonic groups of the polysaccharide, κ-carrageenan, with potassium chloride (KCl) and calcium chloride (CaCl₂). We found that the gelation temperature of κ-carrageenan solutions increased with increasing amounts of K⁺ ions. Apatite formation was observed on the gel after exposure to simulated body fluid for 0.5 day when the gel was prepared with a molar ratio of Ca²⁺/sulfonic groups = 1.5. These results indicate that a thermosensitive κ-carrageenan hydrogel with apatite-forming ability was obtained through the incorporation of K⁺ and Ca²⁺ ions into the solution.