Pressure-induced transparency of MgO,Al2O3, AlN,and cBN ceramics at room temperature

The in situ axial X-ray diffraction patterns of four ceramic powder samples (MgO, Al₂O₃, AlN, and cBN) that were compressed in a diamond anvil cell under uniaxial non-hydrostatic conditions were recorded. The microscopic deviatoric stress as a function of the pressure was determined from the X-ray diffraction peak broadening analysis: the curves increased approximately linearly with the pressure at the initial compression stage and then levelled off under further compression. Pressure-induced transparency was observed in all of the samples under compression, and the pressure at the turning point on the curves of the microscopic deviatoric stress versus pressure corresponded to the pressure at which the samples became transparent. Analysis of the microstructural features of the pressure-induced transparent samples indicated that the compression caused the grains to fracture, and the broken grains bonded with each other. We demonstrated that the ceramics’ pressure-induced transparency was a process during which the grains were squeezed and broken, the pores were close between the grains, and the broken grains were re-bonded under compression.     

供水管网DMA优化分区设计方案

实施独立计量分区(district metered area,DMA)是辅助供水管网管理和漏损识别的重要手段.图划分算法是进行DMA分区的方法之一,常规图划分算法应用中,存在解空间受限、分区后原水流状态易发生较大改变、形成较多串联分区(对流量计算不利)的缺点.在常规图划分算法基础上进行了改进:粗化阶段按照特定规则匹配、合并非输水干管两端的节点,形成简化的管网拓扑结构;分区阶段得到管网初步分区方案;细化阶段提出基于贪心算法、枚举算法、蒙特卡洛算法的分区调整方法,结合改进的仪表安置方法、水力模拟、优劣解距离法(technique for order preference by similarity to an ideal solution,TOPSIS),对分区方案进行调整.将该方法应用于YX市供水管网,成功进行了分区.     

A mini review on two-dimensional nanomaterial assembly

Two-dimensional (2D) nanomaterials have attracted a great deal of attention since the discovery of graphene in 2004, due to their intriguing physicochemical properties and wide-ranging applications in catalysis, energy-related devices, electronics and optoelectronics. To maximize the potential of 2D nanomaterials for their technological applications, controlled assembly of 2D nanobulding blocks into integrated systems is critically needed. This mini review summarizes the reported strategies of 2D materials-based assembly into integrated functional nanostructures, from in-situ assembly method to post-synthesis assembly. The applications of 2D assembled integrated structures are also covered, especially in the areas of energy, electronics and sensing, and we conclude with discussion on the remaining challenges and potential directions in this emerging field.

     

基于高频损耗比的干式空心电抗器制造缺陷检测方法及应用探讨

本文通过分析电抗器因制造工艺导致少匝和极限工艺偏差时600Hz损耗,提出高频损耗可作为电抗器制造缺陷的检测手段及其适用范围,并以600Hz的实测损耗与理论损耗之比是否超过1.5作为判据,以同组任两台损耗之比是否超过1.5作为辅助判据,同时列举应用实例.     

安家岭露天矿过采空区危险源辨识及安全措施研究

危险源辨识对提高煤矿安全生产具有重要的现实意义。研究建立了基于层次分析法的安家岭露天矿危险源辨识模型,确定了危险源指标的权重。依据危险源辨识的权重研究了安家岭露天矿过采空区安全开采存在的主要危险源,并把采空区分为高温明火采空区、积水采空区、存在有毒气体的采空区、未冒实采空区,针对不同的类别的采空区提出了相应的安全开采措施。     

马钢张庄矿高压辊磨机装配工艺研究

针对马钢张庄矿高压辊磨机辊套疲劳断裂严重、对辊精度不能满足生产要求等问题，马钢重机公司根据张庄矿实际生产要求对对辊进行国产化，国产化内容包括辊轴、辊套等零部件的新制以及装配工艺攻关，通过技术研发同时结合实际生产经验，成功对高压辊磨机辊套与辊轴以及辊轴与轴承进行装配，完成了张庄矿高压辊磨机整对对辊的国产化，为该型设备后续生产及优化提供了理论和实践参考依据。     

H型丝光沸石催化剂催化甲苯与叔丁醇的烷基化反应

针对合成对叔丁基甲苯传统工艺中存在的缺点,采用环境友好、可重复利用的H型丝光沸石催化剂(以下简称催化剂)进行了甲苯与叔丁醇的烷基化反应,并用X射线衍射和氨程序升温脱附等方法对不同焙烧温度下得到的催化剂的物相结构和酸性质进行了表征,研究了各种反应条件对催化剂的催化性能的影响。实验结果发现,在适宜的操作条件下,即催化剂的焙烧温度823K、反应温度180℃、反应时间3h、初始压力1.0MPa、原料与催化剂的质量比为8、叔丁醇与甲苯的摩尔比为4、溶剂环己烷与甲苯的摩尔比为5时,甲苯转化率达42.73%,叔丁基甲苯的选择性为96.30%,对叔丁基甲苯的选择性为80.37%。