ACTNET: End-to-End Learning of Feature Activations and Multi-stream Aggregation for Effective Instance Image Retrieval

International Journal of Computer Vision - We propose a novel CNN architecture called ACTNET for robust instance image retrieval from large-scale datasets. Our key innovation is a learnable...     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Broad-band MMICs based on modified loss-compensation method using 0.35-/spl mu/m SiGe BiCMOS technology

Using the concept of loss compensation, novel broad-band monolithic microwave integrated circuits (MMICs), including an amplifier and an analog multiplier/mixer, with LC ladder matching networks in a commercial 0.35-mum SiGe BiCMOS technology are demonstrated for the first time. An HBT two-stage cascade single-stage distributed amplifier (2-CSSDA) using the modified loss-compensation technique is presented. It demonstrates a small-signal gain of better than 15 dB from dc to 28 GHz (gain-bandwidth product=157 GHz) with a low power consumption of 48 mW and a miniature chip size of 0.63 mm² including testing pads. The gain-bandwidth product of the modified loss-compensated CSSDA is improved approximately 68% compared with the conventional attenuation-compensation technique. The wide-band amplifier achieves a high gain-bandwidth product with the lowest power consumption and smallest chip size. The broad-band mixer designed using a Gilbert cell with the modified loss-compensation technique achieves a measured power conversion gain of 19 dB with a 3-dB bandwidth from 0.1 to 23 GHz, which is the highest gain-bandwidth product of operation among previously reported MMIC mixers. As an analog multiplier, the measured sensitivity is better than 3000 V/W from 0.1 to 25 GHz, and the measured low-frequency noise floor and corner frequency can be estimated to be 20 nV/sqrt(Hz) and 1.2 kHz, respectively. The mixer performance represents state-of-the-art result of the MMIC broad-band mixers using commercial silicon-based technologies     

Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Effect of rotor profiles on the torque of a switched-reluctancemotor

The authors examine effects on the torque that simple variations of the standard rotor pole face profile could have, basically from an elementary viewpoint of how the modified profiles affect the distribution and magnitude of the radial and tangential components of the flux density. It is observed that the average torque is mostly affected by changes that alter the dominant radial component, such as changes in the effective air gap length. The other observation that an increase in the average torque can also be obtained by a favorable shift in the torque versus angle characteristics by relatively simple changes of the rotor pole profile is not so well known. Such a shift that reduces the slope of the torque angle characteristic, skewing the curve towards the unaligned position, has two advantages: one is that the phase inductance is at its maximum positive slop and, hence, the maximum torque, when the phase is energized; second, the flatter inductance profile near the aligned position when the phase current is to be commutated would allow a faster drop off of the commutated current and, thus, a smaller negative torque     

Simulation of frequency nonselective mobile channel with LOScomponent: a deterministic approach

A deterministic digital simulation model with finite sum of properly weighted sinusoids is used to simulate a frequency nonselective mobile channel with LOS component. Measurement data are used to optimise the parameters. Which are then used in the deterministic simulation model. The probability distribution and level cross rate (LCR) obtained from the measured data agree well with the analytical and simulation results     

Method for error recovery of line spectral frequencies

The authors have exploited the ideas used in vector quantisation for error recovery of scalar quantised LSFs. The good performance of this method has provided high resistance of the LSFs to channel errors, outperforming other schemes by, possibly, a considerable margin. Better objective and subjective performances were obtained with this new method which obviates the need for more powerful FEC schemes for transmission over noisy channels.<>