Aluminum based reflective nanolens arrays to improve the effectiveness of ultraviolet inactivation of Escherichia coli O157:H7 and Listeria monocytogenes in water and a sucrose solution

Food Science and Biotechnology - Aluminum based reflective nanolens arrays were developed via a series of aluminum electropolishing and anodization steps with subsequent selective dissolution of...     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

HP295中间裂纹产生机理分析及控制措施

通过对HP295封头冲压开裂件缺陷光电镜分析,查找到缺陷产生部位及其导致原因。对多组铸坯低倍样检查,发现中间裂纹是缺陷根源。此后,根据现场生产情况,分析钢中磷、硫含量、钢水过热度、铸机设备精度、拉速和二次冷却强度等因素对铸坯中间裂纹的影响。通过降低磷、硫,控制过热度,调整设备精度,降低拉速以及优化二次冷却等措施,HP295铸坯中间裂纹得到有效控制,用户加工开裂现象完全杜绝。     

Structures and properties of chicken myofibrillar protein gel induced by microwave heating

Structures and properties of myofibrillar protein gel prepared at different power (300–800 W) were evaluated. Amino acid analysis demonstrated that changes in microwave power did not alter primary structure of gel. However, an increase in microwave power could change higher structures of gel. As microwave power increased, α-helix content decreased and β-sheet content increased. Increased microwave power probably facilitated protein to unfold and expose the internal groups, causing surface hydrophobicity and the formation of disulphide bonds were enhanced, which indicated changes in tertiary and quaternary structures of protein. At 500 W, gel had the best ultrastructure where surface morphology, springiness and water holding capacity reached the optimum. Our findings suggested that microwave at an appropriate power (500 W) could change higher structures of myofibrillar protein gel to achieve desired processing and quality protein gel characteristics.     

SUBSCRIPTION 2018

正Four issues per volume a year,CHINA’S REFRACTORIES is distributed worldwide by airspeed delivery at no extra cost to subscribers.     

中压蒸汽管道焊接质量统计分析及建议

中压蒸汽管道作为工厂的公用管网的组成部分,在生产中起着非常重要的作用,其主要用于压缩机蒸汽透平等关键工艺单元,除了对材料有特殊要求外,还要求运行可靠、管内高度洁净,因此对焊接质量提出了更高要求。结合齐鲁石化公司煤代油技术改造工程的中压蒸汽管道的施工,就焊接质量用统计分析的方法,对焊接产生的气孔、夹渣、未焊透等缺陷产生的原因及采取的控制措施进行了分析,并就今后的焊接质量控制提出建议。     

聚氨酯胶粘剂在苯板夹心板生产中的应用

简要介绍了聚氨酯胶粘剂在彩钢板／聚苯乙烯夹心板生产中的应用、采用双组分无溶剂发泡型聚氨酯胶粘剂生产夹心板的工艺。对胶粘剂配制中原料的选择和工艺参数的确定进行了讨论。采用由聚醚、水、催化剂等配成的混合物为A组分，多异氰酸酯作为B组分，制成的发泡型聚氨酯胶粘剂具有固化速度快、成本低、实用效果好等优点，滴胶和抹胶的施工方法工艺简单，可满足夹心板生产的需要。     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

利用信息融合方法的三维特征提取

本文提出了一种基于信息融合的物体三维特征的提取方法，该方法利用两幅互相配准的三维测距图像和灰度图像，来提取多面体的三维特征。首先，通过分析灰度图像中的灰度变化及测距图像中的测距值变化，分别求取各自图像中物体的特征点及特征边；然后，利用两配准图像之间的对应关系，求得所有特征点、面与多边形在三维测距图像中的三维表示；接着，通过分析三维测距图像中所测得的各候选平面上特定点与边处的曲率及法向，验证候选平面