Linear crosstalk in 4×4 semiconductor optical amplifier gateswitch matrix

We report a comprehensive crosstalk investigation of a packaged InGaAsP/InP 4×4 semiconductor optical amplifier gate switch matrix, experimentally as well as theoretically. For a fully loaded switch with the same wavelength on all four inputs, all possible switching combinations are analyzed, thus yielding realistic crosstalk figures. Coherent and incoherent crosstalk phenomena are identified, and a switch crosstalk less than -40 dB has been measured     

Characteristics of Metal Droplets in Slag Tapped from the Blast Furnace

Slag samples, hot‐metal samples and hot‐metal temperatures were obtained during tapping of two blast furnaces. Sampling was carried out at different time points during tapping of three separate heats. The size distribution and composition of metal droplets found in the slag were determined using scanning electron microscopy. Only metal droplets above 0.75 μm could be counted and analysed. All droplets were below 8 μm in diameter and the great majority of these droplets were found to be between 0.75 and 2 μm. The size distribution did not differ significantly for different slag samples. Iron was the main droplet component. Electron probe microanalysis showed that the droplets contained small amounts of carbon. The percentage of the area in a studied cross‐section that was covered with metal droplets varied between 0.01 and 0.07%. Calculations based on Stoke's law showed that the distance droplets travel in the slag is in the micron range. Slag samples taken in the beginning of slag tapping contained more droplets than those taken in the middle of slag tapping, an indication that most droplets can be found in the area near the furnace wall. Some droplets were determined to have magnesium enrichment at the external surface.     

Design and evaluation of fundamental-mode and polarization-stabilized VCSELs with a subwavelength surface grating

We demonstrate 850-nm oxide-confined vertical-cavity surface-emitting lasers (VCSELs) with a locally etched subwavelength surface grating that are single-mode and polarization stable from threshold up to thermal roll-over, reaching /spl sim/4 mW of output power. The side-mode suppression ratio (SMSR) is >30 dB and the orthogonal polarization suppression ratio (OPSR) is /spl sim/20 dB. Moreover, no distortion of the far-field beam profile is observed as a result of the surface grating. Our numerical calculations show that a carefully designed VCSEL can have a high simultaneous mode and polarization selectivity without a significant increase in loss for the favored fundamental mode with polarization state perpendicular to the grating lines. This indicates characteristics such as threshold current and resonance frequency will not be notably degraded. The calculations also show a low sensitivity to variations in grating etch depth and duty cycle, which relaxes fabrication tolerances. In our experimental parametric study, where the oxide aperture diameter, surface grating diameter, and grating duty cycle were varied, the combined mode and polarization selection was investigated. For an optimum combination of oxide aperture and surface grating diameters of 4.5 and 2.5 /spl mu/m, respectively, the device is found to be single-mode and polarization stable for a broad range of grating duty cycles, from 55% to 75%, with only a small variation in other laser performances, which is in line with theory.     

Single fundamental-mode output power exceeding 6 mW from VCSELs with a shallow surface relief

A single fundamental-mode output power of 6.5 mW was achieved from an 850-nm vertical-cavity surface-emitting laser (VCSEL) with a shallow surface relief, the highest single-mode power ever reported using this technique. The VCSELs were fabricated from epitaxial material grown to yield an antiphase reflection from the topmost layer. A circular surface relief, acting as a mode discriminator, was etched in the center to reduce the mirror loss for the fundamental mode. This "inverted" surface-relief technique offers relaxed etch depth control and, therefore, improves reproducibility and yield.     

A multiscale dynamic programming procedure for boundary detection in ultrasonic artery images

Ultrasonic measurements of human carotid and femoral artery walls are conventionally obtained by manually tracing interfaces between tissue layers. The drawbacks of this method are the interobserver variability and inefficiency. In this paper, we present a new automated method which reduces these problems. By applying a multiscale dynamic programming (DP) algorithm, approximate vessel wall positions are first estimated in a coarse-scale image, which then guide the detection of the boundaries in a fine-scale image. In both cases, DP is used for finding a global optimum for a cost function. The cost function is a weighted sum of terms, in fuzzy expression forms, representing image features and geometrical characteristics of the vessel interfaces. The weights are adjusted by a training procedure using human expert tracings. Operator interventions, if needed, also take effect under the framework of global optimality. This reduces the amount of human intervention and, hence, variability due to subjectiveness. By incorporating human knowledge and experience, the algorithm becomes more robust. A thorough evaluation of the method in the clinical environment shows that interobserver variability is evidently decreased and so is the overall analysis time. We conclude that the automated procedure can replace the manual procedure and leads to an improved performance.     

Influence on the stability of generator rotors due to radial and tangential magnetic pull force

Forces due to nonuniform airgaps in rotating electrical machines have been a research topic for over 100 years. However, most research in the area of rotating electrical machines has been performed on motors. Large forces in hydropower generators can lead to expensive damage and failures. Therefore, it is of interest to calculate the forces that arise in a large synchronous generator with an eccentric rotor and study the influence these forces have on the stability of the generator rotor. A 74 MVA synchronous hydropower generator was simulated with an eccentric rotor, using a time-stepping finite-element technique. The forces were calculated using Coulomb's virtual-work method and simulations were performed for no-load and load cases. The resulting force was found to be reduced significantly when a damper winding was taken into account. An interesting effect of the rotor damper winding was that it reduced the eccentricity force and introduced a force component perpendicular to the direction of eccentricity. The results from the finite-element simulations were used to determine how the forces affect the stability of the generator rotor. Damped natural eigenfrequencies and damping ratio for load and no-load conditions are presented. When applying the forces computed in the time-dependent model, the damped natural eigenfrequencies were found to increase and the stability of the generator rotor was found to be reduced compared with when the forces were computed in a stationary model.     

Design of a General‐Purpose European Compound Screening Library for EU‐OPENSCREEN

This work describes a collaborative effort to define and apply a protocol for the rational selection of a general‐purpose screening library, to be used by the screening platforms affiliated with the EU‐OPENSCREEN initiative. It is designed as a standard source of compounds for primary screening against novel biological targets, at the request of research partners. Given the general nature of the potential applications of this compound collection, the focus of the selection strategy lies on ensuring chemical stability, absence of reactive compounds, screening‐compliant physicochemical properties, loose compliance to drug‐likeness criteria (as drug design is a major, but not exclusive application), and maximal diversity/coverage of chemical space, aimed at providing hits for a wide spectrum of drugable targets. Finally, practical availability/cost issues cannot be avoided. The main goal of this publication is to inform potential future users of this library about its conception, sources, and characteristics. The outline of the selection procedure, notably of the filtering rules designed by a large committee of European medicinal chemists and chemoinformaticians, may be of general methodological interest for the screening/medicinal chemistry community. The selection task of 200K molecules out of a pre‐filtered set of 1.4M candidates was shared by five independent European research groups, each picking a subset of 40K compounds according to their own in‐house methodology and expertise. An in‐depth analysis of chemical space coverage of the library serves not only to characterize the collection, but also to compare the various chemoinformatics‐driven selection procedures of maximal diversity sets. Compound selections contributed by various participating groups were mapped onto general‐purpose self‐organizing maps (SOMs) built on the basis of marketed drugs and bioactive reference molecules. In this way, the occupancy of chemical space by the EU‐OPENSCREEN library could be directly compared with distributions of known bioactives of various classes. This mapping highlights the relevance of the selection and shows how the consensus reached by merging the five different 40K selections contributes to achieve this relevance. The approach also allows one to readily identify subsets of target‐ or target‐class‐oriented compounds from the EU‐OPENSCREEN library to suit the needs of the diverse range of potential users. The final EU‐OPENSCREEN library, assembled by merging five independent selections of 40K compounds from various expert groups, represents an excellent example of a Europe‐wide collaborative effort toward the common objective of building best‐in‐class European open screening platforms.     

A High-Resolution TEM/EELS Study of the Effect of Doping Elements on the Sliding Mechanisms of Sputtered WS2 Coatings

It has been shown many times that cosputtering low-friction coatings of molybdenum disulfide (MoS₂) and tungsten disulfide (WS₂) with other elements can improve the structural, mechanical, and tribological properties. To achieve the lowest friction, MoS₂ or WS₂ should be doped with element(s) improving the hardness and density of the coatings. On the other hand, such elements, or their compounds, should not be present in the outermost molecular layers at the sliding interface. This article suggests that there are important differences between how MoS₂ and WS₂ coatings respond to or react with doping elements, despite the almost identical structure and behavior of the undoped materials. Two systems have been investigated by high-resolution transmission electron microscopy (HRTEM) and scanning TEM (STEM) electron energy loss spectroscopy (EELS), W-S-C-Cr and W-S-C-Ti, and showed significant amounts of oxides, which typically formed a layer just underneath the crystalline WS₂ top layer. Further, carbon was almost completely absent in the tribofilms, despite the fact that the as-deposited coatings contained as much as 40–50 at% C. An interesting observation here is that WS₂ basal planes surround or embed Fe wear particles, suggesting a relatively strong adhesion or a Fe-S chemical bonding between iron/steel and WS₂. The result of this is that the wear particles become pacified and remain in the contact as low-friction material.     

Multi-storey timber buildings: breaking industry path dependency

The Swedish legal restriction on construction of multi-storey timber buildings was imposed in 1888 and repealed in 1994. The subsequent emergence of such a timber building system in Sweden is analysed in the context of the existing concrete-based construction system. The characteristics of the construction industry and its path dependency over the past century hamper the development of a timber building system. However, government policies and funding, the wood industry's interest in an enhanced market for value-added wood products, and involvement of the wood research community has helped develop such a construction system. Investments in knowledge creation, incentives for the entry of new firms, and increased prefabrication may facilitate a transition from this formative phase to a growth phase in the diffusion of timber buildings.

En Suède, les restrictions juridiques frappant la construction de bâtiments en bois de plusieurs étages ont été édictées en 1888 et annulées en 1994. L'auteur analyse l'arrivée résultante d'un tel système de construction en bois en Suède face à la construction en béton qui existe actuellement. Les caractéristiques de l'industrie du bâtiment et sa dépendance au chemin au cours du siècle dernier empêchent le développement d'un système de construction en bois. Toutefois, les politiques officielles et les financements ainsi que les intérêts de l'industrie du bois dans un marché amélioré pour des produits en bois à valeur ajoutée et l'engagement des chercheurs dans le domaine du bois ont aidé à développer un tel système de construction. Les investissements dans la création du savoir, les incitations à l'arrivée de nouvelles entreprises et l'augmentation de la préfabrication peuvent faciliter le passage de cette phase de formation à une phase de croissance à la diffusion des bâtiments en bois.

Mots clés: système d'innovation, restriction, bâtiments de plusieurs étages, dépendance au chemin, systèmes technologiques, charpente en bois, bâtiments en bois, Suède