Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Ensuring primary realization of pressure unit in the vacuum range without typically utilized static expansion system

After the break-up of Czechoslovakia in 1993 the primary metrological standards authority almost fully remained in Slovakia. So we had to build our primary vacuum metrology anew. But we could do it using uptodate techniques that are more effective and they enable us to fulfil our task more effectively and in a shorter time.The steady demand to widen the lower pressure range and a steady demand for maximal accuracy collide with the financial possibilities open to a small country. So it is impossible to follow the classical pattern for the vacuum standards: liquid columns, static expansion system and dynamic expansion system. But it is possible to utilize contemporary progress in construction of piston manometers. This enables us to discard liquid column and static expansion techniques in favour of piston technique [Tesar J, Prazak D. Vacuum 2002; 67: 311, Tesar J, Prazak D, Krajicek Z. In:Proceedings of international symposium on Pressure and Vacuum, 2003. p. 169, Tesar J, Repa P, Prazak D, Krajicek Z, Peksa L. Vacuum 2004; 76: 491.]. Such system fulfils all the needs of a little industrial country and is economically acceptable.     

Reliability of local area networks with bus and ring topologies

The reliability of local area networks with bus and ring topologies with a simple transfer medium are critically analysed. A double transfer medium is used to increase reliability. The efficiencies of these approaches are compared.     

Porous mullite ceramics through diphasic gels of large boehmite and small silica particles

Mullite formation process has been studied in stoichiometric mullite (3Al₂O₃·2SiO₂) diphasic gel containing large boehmite (1 m) and small silica (10 nm) particles. It has been found that initial mullitization did not take place inside the silica phase (cristobalite), but took place in the defect -alumina phase. -alumina was stabilized by silica when the temperature was below 1350°C. At temperatures above 1350°C, mullite crystallized directly. It was suggested that silica diffused into the pores (<1.8 nm) of -alumina and prevented the collapse of -alumina pore structure. On the other hand, when silica was not present, the pore structure of -alumina collapsed and -alumina crystallized at 1100°C. Porous mullite ceramics were obtained by using special diphasic gels containing large boehmite and small silica particles.     

Nanocomposite route to the stabilization of porous ϑ-alumina

Stabilization of -alumina phase by silica was studied in nanocomposite (diphasic) alumina-silica gels by XRD and BET surface areas measurements. Five wt.% of silica (22 nm particles) increased the crystallization temperature of to -alumina by about 100°C from boehmite (10 nm particles) derived alumina. Stabilization of -alumina was caused by the formation of intimate contact (Al-O-Si) between components by diffusion of silica into the defect alumina structure.Also with the Department of Agronomy.     

Hydrophilic polycarbonate chips for generation of oil-in-water (O/W) and water-in-oil-in-water (W/O/W) emulsions

Modification of the surfaces of polycarbonate (PC) with the use of a solution of tin (II) chloride renders them hydrophilic. The surface draping is stable against exposure to water and to alcohols. Exposure to alkanes reduces but does not diminish the effect. The method is compatible—in using the same solvent and temperature—with the hydrophobic modification of PC (Jankowski et al. in Lab Chip 11:1151–1156, 2011). The combination of these methods makes it possible to generate single and multiple monodisperse emulsions with the use of flow-focusing junctions in systems made in PC—a material that is suitable for fabrication of multilayer, high-throughput microfluidic devices.     

Hydrophilic polycarbonate chips for generation of oil-in-water (O/W) and water-in-oil-in-water (W/O/W) emulsions

Modification of the surfaces of polycarbonate (PC) with the use of a solution of tin (II) chloride renders them hydrophilic. The surface draping is stable against exposure to water and to alcohols. Exposure to alkanes reduces but does not diminish the effect. The method is compatible—in using the same solvent and temperature—with the hydrophobic modification of PC Jankowski et al. ( Lab Chip 11:748–752, 2011). The combination of these methods makes it possible to generate single and multiple monodisperse emulsions with the use of flow-focusing junctions in systems made in PC—material that is suitable for fabrication of multilayer, high throughput microfluidic devices.     

Parallel interval-based reasoning in medical knowledge-based system Clinaid

The paper continues a series of papers and a monograph [33], where we have described the conceptual structures as well as the basic architecture of a knowledge-based systemCunaid.     

Least Squares Vertex Baking

We investigate the representation of signals defined on triangle meshes using linearly interpolated vertex attributes. Compared to texture mapping, storing data only at vertices yields significantly lower memory overhead and less expensive runtime reconstruction. However, standard approaches to determine vertex values such as point sampling or averaging triangle samples lead to suboptimal approximations. We discuss how an optimal solution can be efficiently calculated using continuous least‐squares. In addition, we propose a regularization term that allows us to minimize gradient discontinuities and mach banding artifacts while staying close to the optimum. Our method has been integrated in a game production lighting tool and we present examples of representing signals such as ambient occlusion and precomputed radiance transfer in real game scenes, where vertex baking was used to free up resources for other game components.     

System approach to modeling of liver glucose metabolism with physiologically interpreted model parameters outgoing from [18F]FDG concentrations measured by PET

New mathematical models from physiologically interpreted parameters capable of evaluating glucose metabolism within the liver and/or the whole body were developed. The group of pigs in a fasting state and the group of pigs with euglycemic supraphysiological hyperinsulinemia were scanned by positron emission tomography after a single dose of [(18)F]FDG tracer. Simultaneously frequent sampling of the dynamic data of [(18)F]FDG plasma concentration in artery, portal vein and hepatic vein was obtained. A system approach to the liver and/or the whole-body system by the tools of linear dynamic sysztem theory was used. Three kinds of structural models, single input and single output or multiple outputs and multiple inputs and single output, were identified. Differences between the group of fasting pigs and the group of pigs in euglycemic supraphysiological hyperinsulinemia were identified by estimated parameters of the structural models. The suitability of the structural mathematical models for the estimation of physiologically interpreted parameters from PET was validated.