A novel ceramic matrix composite based on YNbO4–TiO2 for microwave applications

This work presents the dielectric properties of YNbO₄ (YNO)–TiO₂ composites in the microwave range. X-ray diffraction analysis demonstrates that the addition of TiO₂ to YNO results in the formation of a Y(Nb_0.5Ti_0.5)₂O₆ phase. In the microwave range, the values of permittivity and dielectric loss did not present major changes with the increment of TiO₂. Moreover, the addition of TiO₂ results in an improvement in the thermal stability of YNO, with YNO63 demonstrating a resonant frequency of ?8.96 ppm.°C^?1. We utilised numerical simulations to evaluate the behaviour of these materials as dielectric resonator antennae and it is found that they exhibit a reflection coefficient below ?10 dB at the resonant frequency, with a realised gain of 4.94 – 5.76 dBi, a bandwidth of 665–1050 MHz and a radiation efficiency above 84%. Our results indicate that YNO–TiO₂ composites are interesting candidates for microwave operating devices.     

Increasing the photocatalytic and fungicide activities of Ag3PO4 microcrystals under visible-light irradiation

The present study reports for the first time the performance of silver phosphate (Ag₃PO₄) microcrystals as photocatalyst (degradation of Rodamine B-RhB) and antifungal agent (against Candida albicans–C. albicans) under visible-light irradiation (455 nm). Ag₃PO₄ microcrystals were synthesized by a simple co-precipitation (CP) method at room temperature. The structural and electronic properties of the as-synthetized Ag₃PO₄ have been investigated before and after 4 cycles of RhB degradation under visible light using X-ray diffraction (XRD), micro-Raman spectroscopy, UV–Vis spectrophotometer and field emission scanning electron microscopy (FE-SEM) images. The antifungal activity was analyzed in planktonic cells and 48h-biofilm of C. albicans by colony forming units (CFU) counting, confocal laser and FE-SE microscopies. Statistical analysis was carried out using SPSS software. Morphological and structural modifications of Ag₃PO₄ were observed upon recycling. After 4 recycles, the material maintained its photodegradation property; an eightfold increase in the efficiency of Ag₃PO₄ was observed in planktonic cells and a two fold increase in biofilm when irradiated under visible light. Thus, higher antifungal effectiveness against C. albicans was obtained when associated with visible-light irradiation.     

Inferring kinetic dissolution of NaCl in aqueous glycol solution using a low-cost apparatus and population balance model

An experimental methodology for inferring brine dissolution rate in monoethylene glycol (MEG) solutions at different temperatures using a webcam combined with a mathematical model is presented. The measurement system is designed to track the RGB (red, green, and blue) colour variations during the dissolution process. A dynamic model augmented with the population balance equation is applied to describe the dissolution process. Moreover, the dissolution rate is consistently related to the temperature and MEG concentration through the driving force based on the Gibbs energy and chemical affinity. The applied low-cost measurement apparatus proved to be a useful resource for tracking the dissolution dynamics in a wide range of undersaturation.     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Synthesis and physicochemical characterization of a well-defined poly(butadiene 1,3)-block-poly(dimethylsiloxane) copolymer

For the first time, order-order and order-disorder transitions were detected and characterized in a model diblock copolymer of poly(butadiene-1,3) and poly(dimethylsiloxane) (PB-b-PDMS). This model PB-b-PDMS copolymer was synthesized by the sequential anionic polymerization (high vacuum techniques) of butadiene 1,3 (B) and hexamethylciclotrisiloxane (D₃), and subsequently characterized by nuclear magnetic resonance (¹H and ¹³C NMR), size exclusion chromatography (SEC), Fourier Transform infrared spectroscopy (FTIR), Small-Angle X-ray scattering (SAXS) and rheology. SAXS combined with rheological experiments shows that the order-order and order-disorder transitions are thermoreversible. This fact indicates that the copolymer has sufficient mobility at the timescale and at the temperatures of interest to reach their equilibrium morphologies.     

Challenges in the Application of Stochastic Modal Identification Methods to a Cable-Stayed Bridge

This paper presents an analysis of the data collected in the ambient vibration test of the International Guadiana cable-stayed Bridge, which links Portugal and Spain, based on different output-only identification techniques: peak-picking, frequency domain decomposition, covariance-driven stochastic subspace identification, and data-driven stochastic subspace identification. The purpose of the analysis is to compare the performance of the four techniques and evaluate their efficiency in dealing with specific challenges involved in the modal identification of the tested cable-stayed bridge, namely the existence of closely spaced modes, the perturbation produced by the local vibration of stay-cables, and the variation of modal damping coefficients with wind velocity. The identified natural frequencies and mode shapes are compared with the corresponding modal parameters provided by a previously developed numerical model. Additionally, the variability of some modal damping coefficients is related with the variation of the wind characteristics and associated with a component of aerodynamic damping.