The effect of solidification time and heat treatment on the fatigue properties of a cast 319 aluminum alloy

Solidification time and heat treatment are known to have a large effect on the microstructure of cast aluminum alloys. This study was conducted to quantify how the fatigue properties of a 319-type aluminum alloy are affected by solidification time and heat treatment. Both porosity-containing (non-hot isostatically pressed (HIP)) and porosity-free (HIP) samples in the T6 (“peak aged”) or T7 (“overaged”) heattreated conditions were tested. As the solidification time increased, the average initiating pore diameter increased and stress-controlled fatigue life decreased. Heat treatment was observed to have a large effect on fatigue properties of the HIP samples. However, in the non-HIP fatigue samples, heat treatment did not significantly change the fatigue life or fatigue strength of the cast 319-type alloy. The absence of an influence of heat treatment on fatigue response is attributed to the predominance of the microporosity in fatigue crack initiation in cast aluminum.     

Critical Shear Stress of Bimodal Sediment in Sand-Gravel Rivers

A new model for the critical shear stress and the transport of graded sediment is presented. The model is based on the size distribution of the bed surface and can be used to compute sediment transport rates in numerical simulations with an active layer model. This model makes a distinction between unimodal and bimodal sediments. It is assumed that all size fractions of unimodal sediments have the same critical shear stress while there is selective transport for the gravel fractions of bimodal sediments. A recently published laboratory transport data set is used to calibrate our model.     

Preexercise meal composition alters plasma large neutral amino acid responses during exercise and recovery

This study was designed to determine metabolic and physical performance responses to ingestion of pre-exercise meals with different macronutrient and fiber profiles. Twelve physically active subjects (6 males and 6 females) were used to investigate the metabolic and physical performance consequences of consuming pre-exercise meals consisting of oat, corn, or wheat cereals. A fasting trial served as the control, and all subjects received each treatment in a Latin-square design. Blood samples were drawn before and 85 min after meal ingestion, during 90 min of cycling exercise (60% VO2peak), after a 6.4 km performance ride, and during 60 min of recovery. Expired air samples were collected to determine nutrient utilization. Resting carbohydrate oxidation rates and plasma insulin concentrations after oat ingestion were less than after wheat, and corn and wheat ingestion, respectively (P < 0.05). During exercise, the change in plasma glucose from pre-exercise was greater after consuming wheat and corn compared with oat (P < 0.05), and it was inversely related to pre-exercise plasma insulin concentration (r = -0.55, P = 0.0001). Plasma free fatty acid concentrations were inversely related to plasma lactate concentrations (r = -0.58, P = 0.0001). Free fatty acid concentrations and fat oxidation were greater in fasting trials than all others, but performance ride times did not differ among treatments. Plasma branched-chain amino acid concentrations resembled their respective meal profiles throughout exercise, the performance ride, and recovery. These results indicate that pre-exercise meal composition can influence glucose homeostasis during early exercise and plasma branched-chain amino acid concentrations over a substantial range of metabolic demands.     

Telechelic polydimethylsiloxanes with terminal acetylenic groups prepared by phase-transfer catalysis

Telechelic, hydroxyalkyl terminated polydimethylsiloxanes were obtained under mild conditions via hydrosilylation of allyl alcohol or ethylene glycol monoallyl ether by oligomeric αω-hydride terminated polydimethylsiloxanes, with the use of a platinum catalyst. They were subsequently modified in a phase transfer catalyzed reaction by propargyl bromide, to give telechelic polysiloxanes terminated by acetylenic groups. The synthetic pathway is described and the characterization of the obtained products is presented.     

Coding distributive lattices with Edge Firing Games

In this note, we show that any distributive lattice is isomorphic to the set of reachable configurations of an Edge Firing Game. Together with the result of James Propp, saying that the set of reachable configurations of any Edge Firing Game is always a distributive lattice, this shows that the two concepts are equivalent.     

Recovering gallium from residual bayer process liquor

Gallium is normally obtained by direct electrolysis as a by-product from Bayer process residual liquor at an aluminum processing plant. However, to permit any net accumulation of the metal, the gallium concentration must be at least about 0.3 g/l in the liquor. This article describes a continuous process of extraction with organic solvents and rhodamine-B, followed by a re-extraction step into aqueous media. The final product is a solid containing up to 18 wt.% Ga in a solid mixture of hydroxides and oxides of gallium and aluminum. This final product can then be electrolyzed to recover the gallium more efficiently.     

Study of siloxane additives migration to the surface of polyester-(melamine)-polyurethane coatings: Aging effects after ethanol cleaning

This study determines the influences of siloxane flow agents’ migration on the outermost surface composition of clearcoats, before and after ethanol cleaning. This evaluation is undertaken to improve adhesion of pressure-sensitive adhesives (PSAs) on automotive paint systems. Most of the siloxane flow agents segregate from the bulk to the clearcoat outermost surface during curing. These additives can cover until 50% of the surface area but X-ray photoelectron spectroscopy (XPS) and time of flight-secondary ion mass spectrometry (ToF-SIMS) analyses indicate that they can be removed by ethanol cleaning. Composition of the cleaned clearcoats surfaces are similar as the composition of clearcoat formulated without siloxane additives: the polyester-(melamine)-polyurethane network is more detected than before cleaning. However, outermost surface analyses show that several aging weeks increase the siloxane additives segregation. This post-cleaning migration modifies the clearcoat surface composition and cancels the chemical modifications due to the ethanol cleaning. XPS analyses show that silicon concentrations after cleaning and aging are inversely proportional to the initial silicon concentrations measured after curing. It highlights that aging has to be controlled to improve adhesion of PSAs on clearcoats. A second ethanol cleaning on aged clearcoats is not effective to remove these new siloxane additives. Their formulation should be different from the flow agents and it could modify their solubility in ethanol. This result could also indicate that these new siloxane additives are not located on the last molecular layer of surface and they would not be soluble in ethanol.     

Anionic polymerization of ethylene oxide with cryptates as counterions: 2

A kinetic study of the anionic polymerization of ethylene oxide has been made in tetrahydrofuran at 20°C, with the cryptate Cs⁺ + [TC] as counterion, [TC] being a spheroidal macrotricyclic ligand. Conductance measurements have been made on THF solutions of ?₄BCs + [TC]. Ionic associations higher than cryptated ion pairs are negligible for living end concentrations lower than 3 × 10^?4 moll^?1. k_± and the alkoxide ion pair dissociation constant K_D were determined from both sets of kinetic data obtained with and without added salt knowing the value of k_? from kinetic data performed with K⁺ + [222] as counterion. Free alkoxide ions are about twenty times more reactive than cryptated caesium ion pairs.     

Comparing the Performance of Organic Solvent Nanofiltration Membranes in Non-Polar Solvents

Organic solvent nanofiltration (OSN) is gradually expanding from academic research to industrial implementation. The need for membranes with low and sharp molecular weight cutoffs that are able to operate under aggressive OSN conditions is increasing. However, the lack of comparable and uniform performance data frustrates the screening and membrane selection for processes. Here, a collaboration is presented between several academic and industrial partners analyzing the separation performance of 10 different membranes using three model process mixtures. Membrane materials range from classic polymeric and thin film composites (TFCs) to hybrid ceramic types. The model solutions were chosen to mimic cases relevant to today's industrial use: relatively low molar mass solutes (330–550 Da) in n-heptane, toluene, and anisole.