Reliability and scale effect in toughness of concrete structures

In the present work, the distribution of the random toughness characteristics (i.e. critical energy release rate, G_1c) has been evaluated on the basis of experimental observations. Fracture test results from three groups of geometrically similar concrete specimens of size (width×total depth×thickness), 420×420×50–1680×1680×200 mm³, made with different maximum aggregate size of 9.5, 19, 38, and 76 mm were analyzed using a recently proposed distribution of extremes. In applications of probability, it is important to use an appropriate distribution type and adequate techniques for estimating the parameters of distribution. In this study, a new type distribution of minima is employed for probability computations. It was noticed that the entropy of distribution increases with the crack length, i.e. the uncertainty of toughness, G_1c, value increases with crack length. A non-linear reduction of the maximum allowable splitting force with the defect size, a, was noticed. For large specimens, the maximum allowable splitting load is more sensitive to the required reliability level than that for small specimens. Reliability increases with aggregate size when all other conditions were constant.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Proposal for st-Routing Protocol

A routing protocol chooses one of the several paths (routes) from a source node to a destination node in the computer network, to send a packet of information. In this paper, we propose a new routing protocol, which we call st-routing protocol, based on st-numbering of a graph. The protocol fits well in noisy environments where robustness of routing using alternative paths is a major issue. The proposed routing protocol provides a systematic way to retry alternative paths without generating any duplicate packets. The protocol works for only those networks that can be represented by biconnected graphs.     

A systematic review on emperor penguin optimizer

Neural Computing and Applications - Emperor Penguin Optimizer (EPO) is a recently developed metaheuristic algorithm to solve general optimization problems. The main strength of EPO is twofold....     

Development of GEP-based functional relationship for sediment transport in tropical rivers

This study presents gene expression programming (GEP), which is an extension to genetic programming (GP), as an alternative approach to modeling the functional relationships for the River Kurau, River Langat, and River Muda of the Malaysia. A functional relation has been developed using GEP with non-dimensional variables. The development of a GEP non-dimensional model is described. This paper compares current prediction equation with the existing GEP model for the same rivers (Zakaria et al. in Sci Total Environ 408:5078–5085, (2010). The presented model in this study is a less input GEP model and that predicts good performance. The proposed GEP approach gives satisfactory results compared to existing predictors.     

Carbon fiber from natural biopolymer Bombyx mori silk fibroin with iodine treatment

Carbon fibers were prepared from silk fibers after an iodine treatment and the carbon yield, fiber morphology, structure and mechanical properties were investigated. A single or multi-step carbonization process was used for the preparation. In the single step process, silk fibroin (SF) fibers were heated from 25 to 800 °C with a heating rate of 5 °C min⁻¹ under Ar atmosphere. However, the carbon fiber obtained was partially melted and was too fragile to handle. For better performance, SF fibers were treated with iodine vapor at 100 °C for 12 h and untreated and iodinated SF fibers were heated from 25 to 800 °C by a multi-step carbonization process, which was defined based on the optimum thermal degradation rate of silk. In this multi-step process, the carbon fibers obtained from iodinated SF were structurally intact and stable in appearance, and the carbon yield achieved was ca. 36 wt.%, much higher than the value for untreated SF. X-ray diffraction, Raman spectroscopy and transmission electron microscopic observation revealed that the obtained carbon fibers from both untreated and iodinated SFs had a basically amorphous structure. The strength of carbon fibers prepared from iodinated SF using the multi-step carbonization was considerably increased compared to that of untreated SF. According to viscoelastic measurement, by heating above 280 °C the iodine introduced intermolecular cross-linking of the SF, and its melt flow was inhibited which produced a higher yield and better performance of the carbon fiber.     

Synergic influence of a surfactant and ultrasonication on the preparation of soluble,conducting polydiphenylamine/silica‐nanoparticle composites

Conducting polydiphenylamine was used to encapsulate silica nanoparticles through the oxidative polymerization of diphenylamine in the presence of ultrasonic irradiation. The polymerization was performed in the presence of sodium lauryl sulfate as a surfactant. Experiments performed in the absence of ultrasound clearly demonstrated that the application of ultrasonication played multiple roles in the preparation of a composite of polydiphenylamine with silica nanoparticles. Ultrasonication dispersed the silica nanoparticles, converted sodium lauryl sulfate to lauryl alcohol, and augmented the dispersion of the silica‐nanoparticle/polydiphenylamine composite in an organic medium. Silica‐nanoparticle/polydiphenylamine composites were also prepared in the absence of ultrasound and/or sodium lauryl sulfate. The silica‐nanoparticle/polydiphenylamine composites were characterized with Fourier trans form infrared spectroscopy, ultraviolet–visible/near‐infrared spectroscopy, and thermogravimetric analysis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3912–3918, 2006     

Graft Copolymerization of Acrylamide onto Oil Palm Empty Fruit Bunch (OPEFB) Fiber

Grafting of acrylamide (AAm) onto oil palm empty fruits bunch fiber using hydrogen peroxide as initiator and methyl acrylate as comonomer was investigated. The amount of comonomer needed to make grafting of acrylamide possible was determined. The percentage of poly(acrylamide) and the comonomer in the final graft copolymer was estimated by elemental analysis. Results obtained indicated that methyl acrylate facilitated the incorporation of acrylamide monomer onto OPEFB. The reactivity ratios for both monomers were determined by using Fineman–Ross plot. The effects of reaction temperature and period as well as amount of the initiator, solvent, monomer and comonomer on the percentage of grafting at fixed amount of comonomer (11 mmol) were studied. Maximum percentage of grafting was achieved when the amount of initiator and solvent 3.98×10⁻³ mol and 50 mL respectively. The optimum reaction temperature was 50 ^○C and the reaction period was 90 min. Highest percentage of grafting was 232% when 25.6 mmol of acrylamide was used under these optimum conditions. The presence of functional group in the grafted polymer is characterized by infrared spectroscopy and the surface morphology is observed by scanning electron microscopy. Thermoanalytic investigation on OPEFB and OPEFB-g-PAAM were carried out to evaluate the thermal stability and respective activation energy of the materials.