Power swing analysis in a future metropolitan electric power system on a contingent trip of cryogenic high-power cables

A cryogenic power cable is expected to be capable of carrying bulk power as a main transmission line in a future metropolitan electric power system. It is important to establish a strategy of how to sustain power supply when such a highly densified power supply route trips from the network due to contingency. It is proposed here that the bulk power transmitted by the cryogenic cable could be distributed into the parallel conventional transmission lines by suitable circuit breaker operations in the system. In this process, power-flow routes are forced to be changed with a remarkable modification in the system configuration. In this paper, the power swings associated with the large power-flow change following contingent faults are analyzed by means of a transient network analyzer. It is found that the proposed system modification could be realized without any harmful power swing if the parameters in generators as well as in control devices have conventional magnitudes. It is shown also by simulations that the margin to occurrence in an unstable power swing is left sufficient even if the parameters deviate somewhat from the present magnitudes.     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

A novel technique for a DC brushless motor without position sensors

A dc brushless motor is a kind of synchronous motor driven by an inverter and requires sensors to detect the rotor position. As one of the methods, the induced voltages of a brushless motor have been utilized in practice. However, there are some problems in this method, e.g., the motor can obtain insufficient torque due to the low induced voltages in a low-speed range. This paper proposes a new method which controls the inverter angular frequency ω₁ by using inherent characteristics wherein the torque current i_r is almost proportional to the internal phase angle φ where the primary flux of a synchronous motor is controlled to be constant. If the parameters of a motor are given exactly, the speed regulation is quite small and the transient characteristics with high response and high starting torque are obtained. Furthermore, it is possible to operate a synchronous motor in the field-weakening range. Here, the principle of the control method and the performance characteristics of a dc brushless motor having no position sensors are discussed. The simulation and the experimental results of the tested machine show that the proposed method is very useful for practical applications.     

Fast computation of computer-generated hologram using Xeon Phi coprocessor

We report fast computation of computer-generated holograms (CGHs) using Xeon Phi coprocessors, which have massively x86-based processors on one chip, recently released by Intel. CGHs can generate arbitrary light wavefronts, and therefore, are promising technology for many applications: for example, three-dimensional displays, diffractive optical elements, and the generation of arbitrary beams. CGHs incur enormous computational cost. In this paper, we describe the implementations of several CGH generating algorithms on the Xeon Phi, and the comparisons in terms of the performance and the ease of programming between the Xeon Phi, a CPU and graphics processing unit (GPU).     

Observation of 3‐D Structure of Bubbles in a Fluidized Catalyst Bed

The interface area between the bubble and emulsion phases in a fluidized catalyst bed is one of the important parameters used to analyze and design the fluidized bed reactor. We used a fast‐scanning X‐ray CT system to observe the bubble shape and structure. We then obtained the transient 2‐dimensional cross sectional gas‐phase distribution in a fluidized catalyst bed. Using image‐processing techniques, pseudo 3‐dimensional images of the bubbles were reconstructed. The bubble structure was studied based on the 3‐dimensional images and the previously obtained results in a 2‐dimensional fluidized bed. It was found that the bubble shape was not spherical but complicated, and that the bubbles ascending in a fluidized catalyst bed consisted of some smaller bubbles.     

Synergic effect of Pd/γ-alumina and Cu/ZSM-5 on the performance of NO x storage reduction catalyst

NO _x reduction with a combination of catalysts, Pd catalyst, NO _x storage reduction (NSR) catalyst and Cu/ZSM-5 in turn, was investigated to elucidate for the high NO _x reduction activity of this catalyst combination under oxidative atmosphere with periodic deep rich operation. The catalytic activity was evaluated using the simulated exhaust gases with periodically fluctuation between oxidative and reductive atmospheres, and it was found that the NO _x reduction activity with this catalyst combination was apparently higher than that of the solely accumulation of these individual activities, which was caused by the additional synergic effect by this combination. The Pd catalyst upstream of the NSR catalyst improved NO _x storage ability by NO₂ formation under oxidative atmosphere. The stored NO _x was reduced to NH₃ on the NSR catalyst, and the generated NH₃ was adsorbed on Cu/ZSM-5 downstream of the NSR catalyst under the reductive atmosphere, and subsequently reacted with NO _x on the Cu/ZSM-5 under the oxidative atmosphere.     

Continual conversion of free fatty acid in rice bran oil to triacylglycerol by immobilized lipase

Rice bran oil containing 30–50% free fatty acid was continually converted to an oil containing more than 75% of triacylglycerol (TG) by means of immobilized lipase. The reaction was carried out at 60°C for 24 h with dehydration and reactant mixing by dry nitrogen flow under a positive nitrogen atmosphere. Enzymatic TG synthesis with evaporation by heating was not suitable because of the increasing peroxide value of the oil. Part of this article was presented at the annual meeting of the Japan Oil Chemists' Society at Sendai, Japan, October, 16, 1990.     

Uniformly Porous Composites with 3-D Network Structure (UPC-3D) for High-Temperature Filter Applications

Uniformly porous composites with 3-D network structure (UPC-3D) have been recently developed via a pyrolytic reactive sintering process, which takes advantage of the evolved CO₂ gas from a decomposing carbonate source (e.g., dolomite, CaMg(CO₃)₂) and does not require any additional pore-forming agent nor long-time burning-out process. Through liquid formation via LiF doping, strong necks are formed between constituent particles before completion of the pyrolysis of carbonate, resulting in the formation of a strong 3-D network structure. The pore size distribution is very narrow (with typical pore size: ∼1 μm), and the porosity was controllable (∼30–60%) by changing the sintering temperature. This article presents the development details of UPC-3D, and reports the recent findings in CaZrO₃/MgAl₂O₄ system, which will be one of the more promising systems for practical applications.     

Synthesis of High Density and Transparent Forsterite Ceramics Using Nano-Sized Precursors and Their Dielectric Properties

Forsterite (Mg₂SiO₄) ceramics were prepared using Mg(OH)₂ and SiO₂ as precursors, and the effect of powder characteristics of Mg(OH)₂ on calcination and sintering was investigated. The use of highly dispersed Mg(OH)₂ powder (HD powder) resulted in a lower calcination temperature. Forsterite powder of high homogeneity and small particle size prepared from the HD powder enabled synthesis of high-density forsterite ceramics by ordinary sintering without applying external pressure. Moreover, transparent forsterite ceramics were successfully synthesized through addition of excess Mg to the precursors to compensate for Mg evaporated during the sintering process. Subsequent dielectric measurements revealed that the transparent forsterite ceramics had a very low dielectric loss (tan δ<10⁻⁴).     

Generalized measuring-worm algorithm: high-accuracy mapping and movement via cooperating swarm robots

Recently, many extensive studies have been conducted on robot control via self-positioning estimation techniques. In the simultaneous localization and mapping (SLAM) method, which is one approach to self-positioning estimation, robots generally use both autonomous position information from internal sensors and observed information on external landmarks. SLAM can yield higher accuracy positioning estimations depending on the number of landmarks; however, this technique involves a degree of uncertainty and has a high computational cost, because it utilizes image processing to detect and recognize landmarks. To overcome this problem, we propose a state-of-the-art method called a generalized measuring-worm (GMW) algorithm for map creation and position estimation, which uses multiple cooperating robots that serve as moving landmarks for each other. This approach allows problems of uncertainty and computational cost to be overcome, because a robot must find only a simple two-dimensional marker rather than feature-point landmarks. In the GMW method, the robots are given a two-dimensional marker of known shape and size and use a front-positioned camera to determine the marker distance and direction. The robots use this information to estimate each other’s positions and to calibrate their movement. To evaluate the proposed method experimentally, we fabricated two real robots and observed their behavior in an indoor environment. The experimental results revealed that the distance measurement and control error could be reduced to less than 3 %.