Preparation of Mn2+-Cu+ co-doped P2O5–ZnO–Al2O3 glasses and their red fluorescence properties

To make a Mn²⁺-doped red glass phosphor that can be excited with ultraviolet (UV) light of light-emitting diodes (LEDs), 60P₂O₅-35ZnO-5Al₂O₃-8MnO-xCu₂O glasses (x = 0-1.00) were prepared by a melt-quenching method at 1200-1400°C for 30-180 minutes in atmospheric air, and the redox of Mn and Cu as well as fluorescence properties were investigated. The Mn²⁺ ion was not reduced and oxidized in the melting, quenching, and annealing processes. The valence of Cu in the glasses changed in the order of 0, 1+, and 2+ with the increase in the amount of Cu₂O and in the melting temperature and time. In this study, a 60P₂O₅-35ZnO-5Al₂O₃-8MnO-0.10Cu₂O glass melted at 1250°C for 90 minutes, having the highest Cu⁺ concentration, showed the strongest Mn²⁺ red fluorescence under the UV light at 275 nm. This strong Mn²⁺ red fluorescence has been caused by the energy transfer from excited Cu⁺ ions to Mn²⁺ ions.     

Anti‐Sway Crane Control Considering Wind Disturbance and Container Mass

A method for estimating the sway angle using an observer has already been proposed. The state observer estimates the sway angle accurately and must use the detected sway angle value. However, the estimated sway angle has an error owing to rope length error, friction force, and wind. Moreover, the container mass cannot be determined, and therefore the observer parameter is not suitable. We already proposed robust antisway control for overcoming rope length error without adding a new sensor. Further, we designed a friction disturbance observer to cancel out the influence of the friction force. In this paper, we first propose a container mass estimation method when a crane system performs rolling up control. The observer parameter can be selected using the estimated mass value. Second, in crane parallel shift control, we propose a robust antisway control even when there is a wind disturbance. We design a wind disturbance observer and propose a wind disturbance estimator to separate the friction observer output from the wind disturbance observer output. We confirm through experiments that the proposed method can reduce vibration.     

Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

Cover Picture: UV‐Light‐Induced Swelling and Visible‐Light‐Induced Shrinking of a TiO2‐Containing Redox Gel (Adv. Mater. 9/2007)

Polyacrylate gels containing Ag⁺ and TiO₂ nanoparticles are shown to swell under UV light and shrink under visible light in water. In work reported by Tetsu Tatsuma and co‐workers on p. 1249, the TiO₂ absorbs UV light and reduces the Ag⁺, whereas the deposited Ag absorbs visible light and dissolves itself. These redox reactions change the interactions between the polymer chains and eventually the volume of the gel, as shown on the cover.     

Phase diagrams calculated for Fe-rich Fe-Si-Co and Fe-Si-Al ordering alloy systems

Theoretical analysis based on the calculation of phase diagrams was employed for Fe-Si-Co and Fe-Si-Al ordering systems to clarify the necessity for the occurrence of phase separation in Fe-base ternary ordering systems. The free energy of Fe-base ternary ordering alloys where B2 and D0₃ ordered structures are formed is evaluated statistically using a pairwise interaction approximation up to second nearest neighbours, taking into account not only the atomic interaction but also the magnetic interaction, based on the Bragg-Williams-Gorsky model. The calculated phase diagrams are consistent with the experimentally obtained ones. The phase diagram calculation in this work is useful to predict the equilibrium states of the ternary ordering systems. The phase separation in ordering alloys is caused by the contribution of excess free energies due to ordering. The influences of ferromagnetism on the two-phase regions are also demonstrated.     

Tunable laser for sensing atmospheric transmission in the infrared region of 11 ∼ 16 µm

We succeeded in observing the continuously tunable, pulsed InSb SFR (Spin-Flip Raman) laser emission in the infrared region of 11～16µm (11.4～16.3µm) from only one InSb device, merely by adjusting the pumping wavelength (11 lines from the infrared NH₃ laser) and the applied magnetic field (0～80 kGauss).     

Effect of rapid sample cooling on efficiency of multiple impurity-atom doping

Shallow and efficient doping of wide band-gap semiconductors has remained one of yet unresolved problems to date. A possible solution to this problem is doping with complexes of a few impurity atoms at a quasi-equilibrium state, which is introduced by controlled cooling of a sample after doping. In this work, (1) we first define a global and quasi-equilibria of our interest based on a simple thermodynamic model for a doped crystal, and then (2) we discuss how the cooling rate affects the probability of impurity-complex formation at a quasi-equilibrium as defined. Our main message is that one should design impurity complexes as small in size as possible which have as large a binding energy as possible. This is a required condition for complex designs when it is difficult to tune the cooling rate.     

Immunochemical characterization of anti-H monoclonal antibodies obtained from a mouse immunized with human saliva

Three IgM class anti-H monoclonal antibodies (1E3, 1E5 and 3H1) were obtained from a BALB/c mouse immunized with human O type saliva. These antibodies were found to agglutinate red cells from O group and A and B subgroups but not from Bombay and para-Bombay individuals whose H antigen was barely detected by anti-H reagents. The agglutination reactions of these antibodies were inhibited by H antigens from human tissues. It was also demonstrated that both 1E3 and 3H1 reacted with H disaccharide (Fuc alpha 1-->2Gal beta), H type 1 (Fuc alpha 1-->2Gal beta 1-->3GlcNAc beta), H type 2 (Fuc alpha 1-->2Gal beta 1-->4GlcNAc beta), H type 3 (Fuc alpha 1-->2Gal beta 1-->3GalNAc alpha) and H type 4 (Fuc alpha 1-->2Gal beta 1-->3GalNAc beta) but not with Lea (Gal beta 1-->3[Fuc alpha 1-->4]GlcNAc beta), Leb (Fuc alpha 1-->2Gal beta 1-->3[Fuc alpha 1-->4]GlcNAc beta), X (Gal beta 1-->4[Fuc alpha-->3]GlcNAc beta) or Y (Fuc alpha 1-->2Gal beta 1-->4[Fuc alpha 1-->3]GlcNAc beta). On the other hand, 1E5 was found to react with H type 1, H type 2, Leb and Y. Because of the unique reactivities against various fucosyl linkages these monoclonal antibodies could be useful not only as anti-H reagents but also as reagents for the structural analysis of fucosylated glycoconjugates.     

Dynamic stress intensity factors analysis of interface crack using line-spring model

In this study, a new method for calculating the dynamic stress intensity factors of a bimaterial bending specimen with an interface crack is proposed by making use of a line-spring model. A pre-cracked bending specimen is modeled by one-dimensional beam finite elements and a line-spring representing the stiffness or compliance of a cracked part. The proposed method enables the one-dimensional analysis of a two-dimensional crack problem; thus the time variations of the dynamic stress intensity factors of a bimaterial bending specimen with an interface crack can be obtained by making use of a personal computer within a few minutes. The results obtained by the proposed method agree reasonably well with those obtained by the two-dimensional finite element method, although a slight difference in period can be found. The proposed method enables rapid evaluation of dynamic stress intensity factors. So a rapid evaluation system of the dynamic fracture toughness of a bimaterial with an interface crack can be achieved by combining an instrumented impact test apparatus with a computer program based on the proposed method which runs on a personal computer.