Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

Analytical studies of four-inch pipe whip tests under BWR LOCA conditions

The purpose of pipe rupture studies in JAERI is to perform model tests on pipe whip, restraint behavior, jet impingement and jet thrust force, and to establish a computational method for analyzing these phenomena. This report presents the analytical results of 4-inch pipe whip tests under BWR LOCA conditions.Dynamic response analyses were performed using the general-purpose finite element program ADINA. The test pipe was modelled by straight beam elements and the four restraints were modelled by a single truss element. The analytical results were compared with the experimental results. Impact time and maximum total restraint force showed good agreement with experimental results. On the other hand, pipe strain and pipe deflection could not be predicted so well. The reason for this is that the sliding of the restraint during the pipe whip movement cannot be considered in the analyses.     

A reconfigurable VLSI-based double-lens tracking camera

Watching and tracking an object while seeing a much wider view is one of advantages of the eye system. We proposed and developed a tracking camera system that mimics the eyes by using double-lens modules. In the system, a wide view is captured through the wide-lens module, while the target in it is tracked and magnified through the telescopic lens module. Electronic circuits for tracking control are implemented onto the reconfigurable VLSI or FPGA in order to embed the parallelism in the tracking algorithm into the hardware. A successfully developed FPGA-based prototype performs high-speed tracking at the video-rate. This work was present in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

Thermal expansion behavior of various aromatic polyimides

The thermal expansion behavior for various aromatic polymides was investigated. Usally polymers, including polyimides, have high thermal expansion coefficients (3–6 × 10^?5 K^?1), compared with metals and ceramics. However, there are some polyimides which have very low thermal expansion coefficients below 1 × 10^?5 K^?1. This property was observed for the polymides obtained from pyromellitic dianhydride or 3,3′ 4,4′-biphenyltetracarboxylic dianhydride and aromatic diamines which were constituted of only benzene rings fused at para positions. It was proposed that their low thermal expansion coefficient related to the linearity in their polymer molecular skeltons.     

Strongyloidiasis associated with nephrotic syndrome

We report a nephrotic syndrome patient with eosinophilia who developed ileus, epigastralgia and malabsorption due to strongyloidiasis which became symptomatic by steroid therapy. The patient was then treated with thiabendazole and recovered. A percutaneous renal biopsy revealed minimal change nephrotic syndrome. This renal injury may be brought on by severe infection of Strongyloides stercoralis. It is important to rule out strongyloidiasis prior to corticosteroid therapy to patients from eosinophilia endemic areas.     

Siliconizing of molybdenum plate using Si2Cl6 and some of its properties

Molybdenum plate was siliconized using Si₂Cl₆ as a silicon source, and the siliconizing conditions and some of its properties were examined. The siliconizing of the molybdenum plate began by the deposition here and there of island-like MoSi₂ deposits 4 to 6m thick in the initial stage (after 10 min induction time), and then coalescence of the deposits proceeded to form a uniform MoSi₂ layer all over the molybdenum plate after 30 min siliconizing time. The weight decrease of the siliconized plate by anodic dissolution in 0.2 M sulphuric acid reduced exponentially with increasing thickness of the MOSi₂ layer, and no weight decrease was observed at all above 16m thickness. The sea water corrosion and sea sand abrasion resistivities of the siliconized molybdenum plate increased with increasing siliconizing temperature and Si₂Cl₆ flow rate.     

Removal of nitrogen oxides from air by chemicals-impregnated carbons

Fixation of nitrogen oxides (NO_x) in air onto granular activated carbon impregnated with chemicals was attempted to improve removal efficiency of NO_x by activated carbon adsorption. Nitric oxide (NO) and nitrogen dioxide (NO₂), were tried to remove by a flow test. Fixed-bed adsorption breakthrough curves were obtained when some kinds of carbon were used. The amount adsorbed of NO₂ changed with the amount and kinds of metallic salts impregnated. Chemicals-impregnated carbons were prepared from a commercial activated carbon. Among obtained carbons, the one which showed the highest selectivity for NO_x was chosen, and its performance with the change in humidity was determined. Removal mechanism of NO₂ was estimated, and the carbon impregnated with potassium hydroxide was found to be superior to any other carbon tested. The amount of the adsorbed NO and that produced by the reduction of NO₂ were determined from the breakthrough curves.     

Acrylic nonaqueous dispersion using butylated melamine-formaldehyde resin as dispersant

A series of acrylic nonaqueous dispersions were prepared by using various kinds of butylated melamine–formaldehyde (BMF) resins as dispersant. The functional group composition of BMF to form stable dispersion was butoxy group more than 13 mol/BMF 1 mol, and methylol group ranged from 1 to 2.5 mol/BMF 1 mol. It is concluded that the anchoring of BMF to acrylic copolymer was due to the formation of covalent bond between methylol group in BMF and hydroxy group in acrylic copolymer.