Matrix Transformation in Boron Containing High-Temperature Co–Re–Cr Alloys

An addition of boron largely increases the ductility in polycrystalline high-temperature Co–Re alloys. Therefore, the effect of boron on the alloy structural characteristics is of high importance for the stability of the matrix at operational temperatures. Volume fractions of ε (hexagonal close-packed—hcp), γ (face-centered cubic—fcc) and σ (Cr₂Re₃ type) phases were measured at ambient and high temperatures (up to 1500 °C) for a boron-containing Co–17Re–23Cr alloy using neutron diffraction. The matrix phase undergoes an allotropic transformation from ε to γ structure at high temperatures, similar to pure cobalt and to the previously investigated, more complex Co–17Re–23Cr–1.2Ta–2.6C alloy. It was determined in this study that the transformation temperature depends on the boron content (0–1000 wt. ppm). Nevertheless, the transformation temperature did not change monotonically with the increase in the boron content but reached a minimum at approximately 200 ppm of boron. A probable reason is the interplay between the amount of boron in the matrix and the amount of σ phase, which binds hcp-stabilizing elements (Cr and Re). Moreover, borides were identified in alloys with high boron content.     

Convolutional solutions of partial difference equations

A significant part of the theory of one-dimensional linear shift-invariant systems is based on the concept of weighting function (or impulse response): the output is the convolution of the weighting function with the input. This paper introduces the concept of linear translation-invariant systems and uses this notion in studying impulse response, z-transforms, and transfer functions for multidimensional systems.     

Availability of systems with partially observable failures

The availability is determined for the following kind of system. When the system is operational (up), it can fail in either one of two modes. However, the system operator does not always diagnose the failure mode correctly. Given that one failure mode has occurred, the authors correctly diagnose the failure mode with a given probability η and misdiagnose it with probability 1-η, where η may vary with failure mode. The problem is modeled by a partially observable Markov process. Numerical results indicate that a high probability of misdiagnosis produces appreciably high system-downtime     

Mapping field density distribution in radiators by microwave noise

In his earlier paper on Active Microwave Radiometry, the author indicated that microwave noise can be used to map field density distribution inside radiators and in antenna systems, without the need for anechoic chambers. The presented paper gives details and results of such experiment. The method is described, details of equipment are given and results are presented with a concluding commentary.     

Observation of higher order NMR larmor lines by SQUID in solids at low magnetic field

We describe an apparatus allowing the observation of the NMR static longitudinal component of nuclear magnetizationM _z by a SQUID at low magnetic fields and atT=4.2 K in Plexiglas, Teflon, and CaF₂. The higher order NMR Larmor lines at 2f ₀, 3f ₀, and 4f ₀, wheref ₀ is the Larmor frequency of the allowed NMR line, were measured. These lines correspond to a flip of two, three, and four spins, respectively, by one photon. The amplitudes of 2f ₀ and 3f ₀ lines and their field dependences show that the common assertion that the forbidden lines at 2f ₀ and 3f ₀ appear in the same order of perturbation theory and that their intensity decreases with static magnetic fieldB ₀ asB ₀ ^–2 is wrong. In fact, the third Larmor line 3f ₀ appears at higher order than the second Larmor line 2f ₀ and its intensity decreases asB ₀ ^–4 . This is also shown by a theoretical calculation of its intensity. For the first time the NMR SQUID technique allowed the detection of the 4f ₀ line, corresponding to the simultaneous flip of four spins by one photon.     

Isobutylene polymerization in the presence of t-BuCl/SnCl4

Summary The effect of tert-butyl chloride in the polymerizations of isobutylene carried out in the presence of SnCl₄ in dichloromethane at temperatures-20°C and-78°C was investigated. Synthesized polyisobutylene samples showed a bimodal molecular weight distribution (MWD) and it was found that the weight content of the lowermolecular weight (LMW) fraction increased with increasing t-BuCl concentration in the polymerization mixture. The effect of ageing of the initiation mixture t-BuCl/SnCl₄ in CH₂Cl₂ prepared in advance on MWD of the PIB samples was also studied. Ageing of the initiation system supports the formation of the LMW fraction and this oily PIB is the only product of the polymerization at-20°C, .