Synthesis,characterization and charge transport properties of Pr–Ni Co-doped SrFe2O4 spinel for high frequency devices applications

Ferrites are materials of interest due to their broad applications in high technological devices and a lot of research has been focused to synthesize new ferrites. In this regard, an effort has been devoted to synthesize spinel Pr–Ni co-substituted strontium ferrites with a nominal formula of Sr_1-xPr_xFe_2-yNi_yO₄ (0.0 ≤ x ≤ 0.1, 0.0 ≤ y ≤ 1.0). The cubic structure of pure and Pr–Ni co-substituted strontium ferrite samples calcinated at 1073 K for 3 h has been confirmed through X-ray diffraction (XRD). Average sizes of crystallites (18–25 nm) have been estimated from XRD analysis and nanometer particle sizes of synthesized ferrites have been further verified by scanning electron microscopy (SEM). SEM results have also shown that particles are mostly agglomerated and all the samples possess porosity. It has been observed that at 298 K, the values of resistivity (ρ) increase, while that of AC conductivity, dielectric loss, and dielectric constants decrease with increasing amounts of Pr³⁺ and Ni²⁺ ions. The values of dielectric parameters initially decrease with frequency and later become constant and can be explained on the basis of dielectric polarization. Electrochemical impedance spectroscopy (EIS) studies show that the charge transport phenomenon in ferrite materials is mainly controlled via grain boundaries. Overall, synthesized ferrite materials own enhanced resistivity values in the range of 1.38 × 10⁹–1.94 × 10⁹ Ω cm and minimum dielectric losses, which makes them suitable candidates for high frequency devices applications.     

Ambient‐cured polyesteramide‐based anticorrosive coatings from linseed oil—A sustainable resource

Ambient‐cured polyesteramide (APEA) coating resin synthesized from dihydroxy fatty amide obtained from linseed oil, a sustainable resource, and poly(styrene‐co‐maleic anhydride), a bifunctional acid component, was found to exhibit improved physicomechanical and anticorrosive properties. The structural elucidation of APEA resin has been carried out by FTIR, ¹H‐NMR, and ¹³C‐NMR spectroscopies. The physicomechanical and chemical resistance properties were investigated by standard methods. The corrosion resistance performance was evaluated in acid, alkali, and organic solvent. The thermal behavior was studied by TGA technique. A comparative study of these properties of APEA with reported baked polyesteramide (PEA) coatings was carried out. A remarkable improvement in the drying property of APEA was observed. The APEA coatings also showed improved physicomechanical and anticorrosive properties as compared to the baked PEA coatings. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1818–1824, 2005     

Theoretical Investigation of Cubic BaVO<Subscript>3</Subscript> and LaVO<Subscript>3</Subscript> Perovskites via Tran–Blaha-Modified Becke–Johnson Exchange Potential Approach

The full potential linearized augmented plane wave method of density functional theory has been used to investigate the structural, electronic, magnetic and thermoelectric properties of cubic perovskites BaVO₃ and LaVO₃. The ferromagnetic ground state has been found to be stable by comparing the total energies of non-spin-polarized and spin-polarized calculations performed for optimized unit cells. For both compounds, the bond length and tolerance factor are also measured. From the band structures and density of states plots, it is found that both compounds are half-metallic. We found that the presence of V at the octahedral site of these perovskites develops exchange splitting through p-d hybridization, which results in a stable ferromagnetic state. The observed exchange splitting is further clarified from the magnetic moment, charge and spin of the anion and cations. Finally, we also presented the calculated thermoelectric properties of these materials, which show that half-metallic BaVO₃ and LaVO₃ materials are potential contenders for thermoelectric applications.     

A study on the effect of polishing fluid volume in ball end magnetorheological finishing process

Ball end magnetorheological finishing is a unique process that utilizes a magnetically controlled ball of polishing fluid at the tip of the rotating tool to finish workpiece of different materials and shapes. The aim of this research is to study the effect of polishing fluid volume on finishing spot size and the surface finish associated with it. A magnetostatic simulation is done to find the variation of flux density in the working gap and on the workpiece surface. The maximum limit of the polishing fluid volume is selected on the basis of area of threshold magnetic flux density (minimum value required for finishing) region on the workpiece surface. The surface characteristics and the diameter of the finished spot are analyzed by varying the fluid volume. The surface obtained with high fluid volume is poorly finished and has scratch marks as the excess fluid flows out from the working gap and forms a thick ring at the periphery of the tool tip. Contrary to this, if the fluid volume is too less, then it merely rotates over the workpiece surface without causing any finishing action. An optimum range of fluid volume produces a good quality surface finish with constant finished spot size.     

Correction on link relative based approach to CUSUM chart

Link relative-based approach was used in an article (see reference 1) to enhance the performance of the cumulative sum (CUSUM) control chart. This technique involves the use of firstly, the link relative variable to convert the process observations in a relative to the mean form and secondly, optimal constants to define a new variable which is used as the plotting statistic of the link relative CUSUM chart. In this article, it is proven through simulation study that the optimal constants with fixed values, as reported in the aforementioned article, give different results. Instead, if the regression technique is used, then the same results will be obtained.     

Selective determination of urea using urease immobilized on ZnO nanowires

Well-aligned zinc oxide (ZnO) nanowire arrays were fabricated on gold-coated plastic substrates using a low-temperature aqueous chemical growth (ACG) method. The ZnO nanowire arrays with 50–130 nm diameters and ∼1 μm in lengths were used in an enzyme-based urea sensor through immobilization of the enzyme urease that was found to be sensitive to urea concentrations from 0.1 mM to 100 mM. Two linear sensitivity regions were observed when the electrochemical responses (EMF) of the sensors were plotted vs. the logarithmic concentration range of urea from 0.1 mM to 100 mM. The proposed sensor showed a sensitivity of 52.8 mV/decade for 0.1–40 mM urea and a fast response time less than 4 s was achieved with good selectivity, reproducibility and negligible response to common interferents such as ascorbic acid and uric acid, glucose, K⁺ and Na⁺ ions.     

Rice-like CuO nanostructures for sensitive electrochemical sensing of hydrazine

In this work, a low temperature aqueous chemical growth methodology was used for the fabrication of CuO nanostructures. The as-synthesised nanostructures were then elaborately characterised by number of analytical techniques such as scanning electron microscopy (SEM) and X-ray powder diffraction (XRD). The obtained nanostructures were observed to possess interlaced rice-shaped structural features with the length and width of individual rice determined to be in the range of 200–300 nm and 50–100 nm respectively. The unique nanostructures when utilised as electrode material exhibited excellent electro-catalytic potential towards oxidation of hydrazine in alkaline media. The excellent conductive of CuO added by the high surface area of obtained nanorice-like structures enabled development of highly sensitive (3087 µA mM⁻¹ cm⁻²), selective and stable electrochemical sensor for hydrazine. In addition, the successfully application of the developed sensor in spiked tap, bottled and industrial water samples for the detection of hydrazine suggested its feasibility for practical environmental application.

     

Synthesis and characterization of novel curcumin based polyurethanes varying diisocyanates structure

In this research work, novel polyurethanes (PUs) based on blends of curcumin/1,4-butane diol (BDO) by varying the structure of diisocyanates were prepared following step growth polymerization. Structural study of blends and various diisocyanates based PU through Fourier Transform Infrared (FTIR) spectroscopy confirmed the incorporation of curcumin into the backbone of the PU. The scanning electron microscopic (SEM) study confirmed the well dispersion of incorporated curcumin and homogeneity of surface of synthesized samples. The SEM results also indicated that surface morphology of synthesized samples much dependent on diisocynates structure. Moreover SEM images inferred that phase separation is more pronounced in aromatic diisocyanate based PU. The anti-bacterial and anti-fungal tests were performed against different strains in order to determine the biocompatibility of the curcumin based PU. The antimicrobial activity results revealed that the material having aromatic diisocyanate are more biocompatible than the aliphatic diisocyanates in the PU structure. On the whole, this work is actually a step towards the generation of novel biocompatible materials preferably useful for biomedical applications.