Electrophoretic deposition of graphene oxide on carbon brush as bioanode for microbial fuel cell operated with real wastewater

Microbial fuel cell (MFC) is a promising technology for simultaneous wastewater treatment and energy harvesting. The properties of the anode material play a critical role in the performance of the MFC. In this study, graphene oxide was prepared by a modified hummer's method. A thin layer of graphene oxide was incorporated on the carbon brush using an electrophoretic technique. The deoxygenated graphene oxide formed on the surface of the carbon brush (RGO-CB) was investigated as a bio-anode in MFC operated with real wastewater. The performance of the MFC using the RGO-CB was compared with that using plain carbon brush anode (PCB). Results showed that electrophoretic deposition of graphene oxide on the surface of carbon brush significantly enhanced the performance of the MFC, where the power density increased more than 10 times (from 33 mWm^?2 to 381 mWm^?2). Although the COD removal was nearly similar for the two MFCs, i.e., with PCB and RGO-CB; the columbic efficiency significantly increased in the case of RGO-CB anode. The improved performance in the case of the modified electrode was related to the role of the graphene in improving the electron transfer from the microorganism to the anode surface, as confirmed from the electrochemical impedance spectroscopy measurements.     

Performance of the decorrelator receiver for DS-CDMA mobile radio system employing RAKE and diversity through Nakagami fading channel

Multiple-access interference (MAI) and multipath fading are two of the most significant factors limiting the capacity and performance of direct-sequence code-division multiple-access (DS-CDMA) systems. In this paper, synchronous multiuser receivers that combine antenna diversity, RAKE reception, and a multipath decorrelator for MAI cancellation are analyzed in a Nakagami faded environment using a maximal ratio combiner or a selection combiner. A coherent binary phase-shift keying employing DS-CDMA is considered. Arbitrary branch correlation is also considered for any diversity order in the case of identical severity fading on the branches.     

Effect of functional group of ferrocene redox substance on the transport properties of newly designed ion exchange membrane prepared from polymer gel

A different newly designed cationic exchange polymer membrane and anionic exchange polymer membrane were introduced, and also the transport properties of these polymeric membranes were investigated in this study. The transport properties of these polymer membranes in contact with ferrocene redox derivatives were estimated by using electrochemical techniques such as cyclicvoltammetry, chronopotentiometry, and chronoamperometry techniques, respectively. The used ferrocene redox substances, which have different functional groups, were (Ferrocenylmethyl) trimethylamonium iodide, FcMA, Ferrocenedimethanol, FcDM, and Ferrocene carboxylic acid, FcCA. It indicated that the performance of a membrane depended on the content of polymer gel, anionic exchange polymer site (20 wt % and 50 wt %) or cationic polymer exchange site (20 wt % and 50 wt %), and the efficiency of the functional groups of cationic and anionic exchange polymer site as well. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Water and salt permeability of reinforcement polymer‐gel composite membrane

The charged mosaic polymer membrane (CMM) without reinforcement and the composite charged mosaic polymer membrane (CCMM) with reinforcement were investigated in terms of salt and water transport (permeability). The composite charged mosaic polymer membrane (CCMM) with reinforcement showed a unique transport behavior such as preferential material transport L_p and ω. Water permeability coefficient, L_p and salt permeability coefficient, ω were estimated by taking account of active layer thickness of composite polymer gel. The L_p and ω values of CCMM with reinforcement were larger than those of CMM without reinforcement. On the other hand, the reflection coefficient of CCMM, σ, showed negative value, which suggested preferential material transport to solvent transport. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Radiation polymerization of acrylonitrile in a viscous system with styrene

Radiation polymerization of acrylonitrile in a viscous system with styrene was performed at ambient temperature by using γ‐rays. It is found that the overall rate of polymerization was accelerated after critical conversion due to the gel effect. As the molar fraction of styrene in monomer feed (f_St) is increased, both the total polymer conversion and molar fraction of acrylonitrile in the copolymer feed (F_AN) were decreased. The monomer reactivity ratios for acrylonitrile and styerne were determined to be r₁ (AN) = 0.25 and r₂ (St) = 2.0, respectively. The copolymers obtained were characterized by Fourier transformed infrared spectra (FTIR), X‐ray diffraction (XRD), scanning electron microscopy (SEM), ¹H‐NMR, and pyrolysis mass spectrometry (PMS). It was found that the slight addition of styrene to acrylonitrile strongly changes crystallinity, morphology, and thermal decomposition of the resulting polymer. ¹H‐NMR measurment of AN/St copolymer showed the appearance of aromatic proton signals and shifted the resonance of the methylene proton to lower chemical shifts. The mass spectra of AN/St copolymers showed fragments of pyrolysates corresponding to oligonitriles with styrene end groups. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 268–275, 2002; DOI 10.1002/app.10324     

Modification of leather properties by grafting. I. Effect of monomer chain on the physico‐mechanical properties of grafted leather

Although leather has a number of desirable properties such as thermal stability and fire retardancey, in addition to high toughness, it has a few drawbacks such as weight, high water absorption, poor soil and rot resistance, and nonuniformity. If these defects are overcome, leather's usefulness would be further enhanced and its competitive position with respect to synthetics would increase. This study reports the physical and mechanical properties of buffalo leather after chemical graft copolymerization with ethyl acrylate, butyl acrylate, and 2‐ethyl hexyl acrylate using benzoyl peroxide as an initiator. The optimum conditions for grafting (e.g., monomer and initiator concentrations, temperature and time of grafting, and solvent leather ratio) were extensively investigated. The study achieved outstanding properties for buffalo leather in reduction of water uptake after grafting, especially on using 2‐ethyl hexyl acrylate and butyl acrylate monomers. FT‐IR and solid ¹³C‐NMR for leather before and after grafting confirmed the grafting process.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1478–1483, 2003     

Inhibition effect of some polymers on the corrosion of cadmium in a hydrochloric acid solution

The effects of poly(vinyl alcohol) (PVA), poly(acrylic acid) (PAA), sodium polyacrylate (NaPA), poly(ethylene glycol) (PEG), pectin (P), and carboxymethyl cellulose (CMC) on the corrosion of cadmium in a 0.5M hydrochloric acid (HCl) solution were studied with both electrochemical impedance spectroscopy and Tafel plot techniques. Measurements were carried out at cathodic, open‐circuit, and anodic potentials. All the investigated polymers had inhibitory effects on both the cathodic (except for NaPA, P, and CMC) and anodic processes, with a predominant anodic inhibiting action. However, NaPA, P, and CMC exhibited a slight cathodic inhibiting action only at higher polymer concentrations. This behavior may be attributed to the very weak adsorbability of the polymers on the cathodic sites. Because PVA and PEG had hydroxy groups, there could be bridging between the polymer and the surface, resulting in an inhibiting effect in the HCl solution. However, PVA had much greater adsorbability on the surface than PEG at the anodic potential. The adsorption of most of the polymers obeyed a Temkin adsorption isotherm, and this indicated indicating that the main process of inhibition was adsorption. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 866–871, 2003