Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Highly reliable testing of ULSI memories with on-chip voltage-downconverters

Two testing techniques for ultra-large-scale integrated (ULSI) memories containing on-chip voltage downconverters (VDCs) are described. The first in an on-chip VDC tuning technique that adjusts internal V_CC to compensate for the monitored characteristics of the process parameters during repair analysis testing. The second is an operating-voltage margin test, performed at various internal V_CC levels during the water sort test (WT) and the final shipping test (FT)     

Inhibition of acid secretion in gastric parietal cells by the Ca2+/calmodulin-dependent protein kinase II inhibitor KN-93

A novel Ca2+/calmodulin-dependent protein kinase II (CaM Kinase II) inhibitor, KN-93 potently inhibits gastric acid secretion from parietal cells. As previously reported (1), treatment of parietal cells with a selective inhibitor of CaM kinase II, KN-62 resulted in the inhibition of cholinergic-stimulated rabbit parietal cell secretion, whereas it failed to inhibit the histamine and forskolin response. In contrast effects of carbachol, histamine and forskolin were significantly inhibited by KN-93 with an IC50 of 0.15, 0.3 and 1 microM, respectively; these effects occurred without any changes in intracellular cyclic AMP and Ca2+ levels. In the present study we investigated the mechanism by which KN-93 acts upon the acid-secreting machinery of gastric parietal cells. Neither redistribution of the proton pump activity nor the morphological transformation were affected by KN-93. The drug only weakly inhibited the H+, K(+)-ATPase activity but strongly dissipated the proton gradient formed in the gastric membrane vesicles and reduced the volume of luminal space. Thus KN-93 acts at pH gradient formation whereas KN-62 acts only at CaM Kinase II.     

Ozone micro-bubble disinfection method for wastewater reuse system.

Reuse of wastewater is regarded as one important way to deal with the world's shortage of potable water. The authors focused on a disinfection system using micro-bubbles and evaluated its capability for wastewater reuse. This paper reports experimental results from examination of the basic characteristics of micro-bubbles and disinfection of secondary effluent by air or ozone micro-bubbles. The results suggest that when micro-bubbles are applied in an ozonation system it is possible to reduce the reactor size, the amount of ozone decomposition equipment needed and the ozone dose rate.     

Microstructure development of steel during severe plastic deformation

The microstructure development during plastic deformation was reviewed for iron and steel which were subjected to cold rolling or mechanical milling (MM) treatment, and the change in strengthening mechanism caused by the severe plastic deformation (SPD) was also discussed in terms of ultra grain refinement behavior. The microstructure of cold-rolled iron is characterized by a typical dislocation cell structure, where the strength can be explained by dislocation strengthening. It was confirmed that the increase in dislocation density by cold working is limited at 10¹⁶m⁻², which means the maximum hardness obtained by dislocation strengthening is HV3.7 GPa. However, the iron is abnormally work-hardened over the maximum dislocation strengthening by SPD of MM because of the ultra grain refinement caused by the SPD. In addition, impurity of carbon plays an important role in such grain refinement: the carbon addition leads to the formation of nano-crystallized structure in iron.     

Nonmagnetic indenter-type high-pressure cell for magnetic measurements

An indenter-type high-pressure cell has been developed for electric and magnetic measurements in low-temperature and high-magnetic-field environments. The maximum pressure achieved at low temperatures is more than 4.5 GPa, which is higher than that of a conventional piston-cylinder cell. The typical sample space at maximum pressure is 1.6 mm in diameter and approximately 0.7 mm in depth, and magnetic measurements such as ac-susceptibility and nuclear magnetic resonance can be performed using a miniature coil. All the components of the indenter cell are made of nonmagnetic materials that have enough thermal conductivity for low-temperature experiments using a 3He/4He dilution refrigerator. Another indenter-type cell designed for a commercial superconducting quantum interference device magnetometer is also reported.