Dysprosium doped copper oxide (Cu1-xDyxO) nanoparticles enabled bifunctional electrode for overall water splitting

The production of hydrogen, a favourable alternative to an unsustainable fossil fuel remains as a significant hurdle with the pertaining challenge in the design of proficient, highly productive and sustainable electrocatalyst for both oxygen evolution reaction (OER) and hydrogen evolution reaction (HER). Herein, the dysprosium (Dy) doped copper oxide (Cu_1-xDy_xO) nanoparticles were synthesized via solution combustion technique and utilized as a non-noble metal based bi-functional electrocatalyst for overall water splitting. Due to the improved surface to volume ratio and conductivity, the optimized Cu_1-xDy_xO (x = 0.01, 0.02) electrocatalysts exhibited impressive HER and OER performance respectively in 1 M KOH delivering a current density of 10 mAcm^?2 at a potential of ?0.18 V vs RHE for HER and 1.53 V vs RHE for OER. Moreover, the Dy doped CuO electrocatalyst used as a bi-functional catalyst for overall water splitting achieved a potential of 1.56 V at a current density 10 mAcm^?2 and relatively high current density of 66 mAcm^?2 at a peak potential of 2 V. A long term stability of 24 h was achieved for a cell voltage of 2.2 V at a constant current density of 30 mAcm^?2 with only 10% of the initial current loss. This showcases the accumulative opportunity of dysprosium as a dopant in CuO nanoparticles for fabricating a highly effective and low-cost bi-functional electrocatalyst for overall water splitting.     

Effect of 100 KeV Ar+ ion beam irradiation on ZnO thin films – Influence of morphology vis-a-vis electrode/electrolyte interface and its impact on photoelectrochemical water splitting

The present study attempts quantitative determination of changes in the morphological surface features viz. fractal dimension, lower and upper cut off length scale through Power Spectral Density analysis prior to and after irradiation of 100 KeV Ar⁺ ion beam at incidence angles of 0°, 40° and 60° on ZnO thin films. All the unirradiated and irradiated samples are subjected to photoelectrochemical characterization and a correlation between photoelectrochemical performance and morphological parameters is established. Sample irradiated at 40° angle at the fluence of 5 × 10¹⁶ ions/cm² is found to possess maximum fractal dimension of 2.72, lower and upper cut off length scale of 3.16 nm and 63.00 nm respectively. This sample exhibits maximum photocurrent density of 3.19 mA/cm² and applied bias photon-to-current efficiency of 1.12% at 1.23 V/RHE. Hydrogen gas collected for duration of 1 h for the same sample was ~4.83 mLcm^?2.     

An energy-efficient cloud system with novel dynamic resource allocation methods

The Journal of Supercomputing - In the last decade, cloud computing has brought enormous changes to people’s lives. Cloud computing gives a client-driven computational model. In this case,...     

Escherichia coli,Salmonella spp., and Staphylococcus aureus susceptibility to antimicrobials of human and veterinary importance in poultry sector of India

In India, little attention has been paid on antimicrobial resistance (AMR) in the context of developing “One Health” approach. Hence, utilizing multi-disciplinary approach, we assess the AMR level and dynamics/pattern of multi-drug resistance (MDR) in Escherichia coli, Salmonella spp., and Staphylococcus aureus circulating over the different stages of poultry in India. A total of 342 isolates including E. coli (n = 143), Salmonella spp. (n = 104), and S. aureus (n = 95) were recovered from fecal (n = 80) and cecal (n = 80) samples of chicken, collected across the different poultry-retail shops and poultry-farms located at urban and rural areas of Rajasthan, India, respectively. High rates of AMR to drugs that are critically/highly important both in human and veterinary medicine were observed among all the isolates. Upward trends in AMR prevalence was observed in poultry-retail shops than in poultry-farms. Notably, >90% of all the isolates were MDR, of particular, pattern/prevalence of MDR was substantially varied across the poultry-farms vs. poultry-retail shops. Our results indicate AMR including MDR to be common in E. coli, Salmonella spp., and S. aureus distributed frequently in poultry. The study encourages the formulation of national policy, programmes and further research with a “One Health” approach that can benefits to the human/animal and the environment.     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

Micro- and nanofabrication processes for hybrid synthetic and biological system fabrication

The application of micro- and nanofabrication processes to the development of hybrid synthetic and biological systems may enable the production of new devices such as controllable transporters, gears, levers, micropumps, or microgenerators powered by biological molecular motors. However, engineering these hybrid devices requires fabrication processes that are compatible with biological materials such as kinesin motor proteins and microtubules. In this paper, the effects of micro- and nanofabrication processing chemicals and resists on the functionality of casein, kinesin, and microtubule proteins are systematically examined to address the important missing link of the biocompatibility of micro- and nanofabrication processes needed to realize hybrid system fabrication. It is found that both casein, which is used to prevent motor denaturation on surfaces, and kinesin motors are surprisingly tolerant of most of the processing chemicals examined. Microtubules, however, are much more sensitive. Exposure to the processing chemicals leads to depolymerization, which is partially attributed to the pH of the solutions examined. When the chemicals were diluted in aqueous buffers, a subset of them no longer depolymerized microtubules and in their diluted forms still worked as resist removers. This approach broadens the application of micro- and nanofabrication processes to hybrid synthetic and biological system fabrication.