Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

Treatment of hemifacial spasm with botulinum toxin

We injected botulinum toxin to treat hemifacial spasm, and investigated the effects and the patient's impression of this treatment. Average duration of improvement lasted about 3.5 months in both the initial treatment group and the recurrent group. However the patients in the recurrent group received fewer units of botulinum toxin than those in the initial treatment group. Except for local paralysis that disappeared within a month, there were very few complications. Most patient were satisfied with this treatment. We conclude that the treatment of hemifacial spasm with botulinum toxin is both simple and useful.     

Internal excitation of intermediate mass fragments from collisions of 36Ar+Ag nuclei at 35 MeV/nucleon

An extruding wire knife was used to give adult male CFHB rats a minimally traumatic unilateral mechanical lesion of the medial forebrain bundle. In addition, some rats received bilateral intrastriatal injections of one of three fluorescent retrograde tracers either eight days before or eight days after the lesion. Injections made after the lesion revealed that about half of the animals had complete lesions of the nigrostriatal tract, while the other half were incompletely lesioned, the mean proportion of non-axotomized neurons being 23%. Over the 10 weeks following the lesions, the number of tyrosine hydroxylase-immunoreactive cells in the lesioned substantia nigra fell linearly, reaching a mean of 29% of that of the control substantia nigra. In the animals which were completely lesioned, neuronal survival at 10 weeks varied between 6 and 12%. That the disappearance of tyrosine hydroxylase-immunoreactive neurons was due to cell death rather than the loss of tyrosine hydroxylase itself was confirmed by labelling the cells with Fluoro Gold before axotomy; the tracer was seen in survival neurons, microglia and in a few involuted neurons which continued to be tyrosine hydroxylase-immunoreactive. This percentage of neurons surviving axotomy corresponds to the proportion of substantia nigra neurons which project to the contralateral striatum, and these neurons were in the region of the substantia nigra from which the contralateral projection originated. It is concluded that following mechanical transection of the nigrostriatal tract, all truly axotomized substantia nigra neurons die over a period of about 10 weeks.     

Vorticity field structure associated with the 3D Tollmien-Schlichting waves

Details of the vorticity field structure associated with the 3D Tollmien-Schlichting waves have been examined based upon the recent numerical studies of the subject. First, a single obliquet-s wave has been found to have the velocity component parallel to the wave front playing an overall dominant role, in particular, to create the longitudinal vorticity. The so-called Benney-Lin longitudinal vortices are then demonstrated to be, in fact, a minor consequence compared with the localized longitudinal vorticity field and its periodic pumping. Finally, the formation of the longitudinal vorticity field in the fundamental- and subharmonic-mode interactions is explained. The research reported in this paper has been supported in part by Bundesministerium für Forschung und Technologie and by Deutsche Forschungsgemeinschaft. The major part of the paper has been presented at the Third Asian Congress of Fluid Mechanics, 1–5 September 1986, in Tokyo, as a General Lecture by the senior author, FRH.     

Principle and operation of a new type motor consisting of piezoelectric device and strain wave gearing

The authors have developed a new type of motor consisting of a piezoelectric device and strain wave gearing, and is called a piezoelectric motor. This is a first step in realizing a low-speed, small-size and lightweight motor. The principle of the motor is that the traveling wave is produced by piezoelectric devices and displacement conversion devices without mechanical resonance, and the torque to rotate the motor is generated by a mechanism of strain wave gearing (circular spline and flexspline) without using friction. The motor is operated at variable frequency and its rotational position (angle) is controlled in open-loop because it is basically a synchronous motor. In this paper, the structure and principle of the proposed motor are explained and the driving method and the mechanical characteristics of an experimental motor also are described. The results are as follows:

• 1 The realizability of the proposed piezoelectric motor is verified experimentally. The experimental motor operates at 2920 steps per revolution, and its speed range is 0 to 960 pps [or 0 to 20 (rpms)].
• 2 The torque characteristics are clarified qualitatively.
• 3 The generated torque of the experimental motor is small (less than 0.03 Nm) and therefore the improvement of the torque is an important subject hereafter.
• 4 It is possible to construct the motor with nonmetallic material. This fact is considered to facilitate obtaining a means to lighten the weight of the motor in the future.

     

Direct ethoxylation of fatty methyl ester over Al-Mg composite oxide catalyst

For the purpose of estimating the reaction mechanism of the direct ethoxylation of a fatty ester in the presence of an Al-Mg composite oxide catalyst, a labeled fatty methyl ester C₁₁H₂₃CO¹⁸OCH₃ containing ¹⁸O isotope was synthesized and directly ethoxylated. The product was evaluated by gas chromatography-mass spectrometry (GC-MS). The GC-MS spectra showed that the ¹⁸O isotope label was present only in the methoxy group at the molecular end of the ethoxylated fatty methyl ester. This supports the reaction mechanism of coordination anionic polymerization where the bond between the acyl and methoxy groups of the fatty methyl ester molecule was broken, caused by the bifunctional effect of the acid-base active sites; an intermediate chemisorption species was formed; and then ethylene oxide was addition-polymerized sequentially, in parallel.     

Phase Formation and Microstructure of Titanium Oxides and Composites Produced by Thermal Plasma Oxidation of Titanium Carbide

The phase formation and microstructure of titanium oxides and composites produced by Ar–O₂ thermal plasma oxidation of titanium carbide powders were investigated in detail by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Relationships between the phase compositions and microstructures of the oxides were established by combined structural and phase analyses, in correlation with synthesis conditions and phase formation mechanisms. It is revealed that vapor condensation favored the formation of anatase, which existed as smaller particles, while liquid/solid oxidation favored the formation of rutile, which appeared as larger particles or composites. A higher oxygen input in the plasma gases (Ar + O₂) enhanced the formation of anatase due to impeded oxidation and evaporation. A small amount of Ti₄O₇ and Ti₃O₅ was detected in the larger particles coexisting with rutile or TiC. These suboxides were formed as intermediates in solid oxidation of TiC or precipitated from the Ti–C–O melt during cooling. Furthermore, extensive cracks, dislocations and stresses were observed in the monolithic rutile and composites, in association with the rapid quenching in this high-temperature in-flight oxidation process.     

Nitrogen and phosphorus effluent loads from a paddy-field district adopting collective crop rotation

Japanese paddy rice systems commonly adopt the rotation of vegetables, wheat and soybeans with paddy rice. Crop rotation may, however, increase the nutrient load in effluent discharged from the district because more fertilizer is applied to the rotation crops than is applied to paddy crops. We investigated a paddy-field district subject to collective crop rotation and quantified the annual nutrient load of effluent from the district in three consecutive years. The total annual exports of nitrogen and phosphorus over the investigation period ranged from 30.3 to 40.6 kg N ha(-1) and 2.62 to 3.13 kg P ha(-1). The results suggest that rotation cropping increases the effluent nutrient load because applied fertilizer is converted to nitrate, and surface runoff is increased due to the absence of shuttering boards at the field outlets.