Evaluation of inelastic constitutive models under plasticity-creep interaction for steel at 600°C

Uniaxial tests to identify plasticity-creep interaction in steel at 600°C were carried out as the Benchmark Project by the Subcommittee on Inelastic Analysis and Life Prediction, JSMS. The purpose of this paper is to present recent experimental data and predictions of constitutive models obtained in the project. Ten types of constitutive models were utilized to compare analytical predictions to sixteen benchmark experiments which are grouped into four categories: (I) tensile and creep tests under monotonic loading, (II) mixed mode tests under plastic and creep loading, (III) ratcheting deformation tests under program loads, and (IV) cyclic deformation tests under the combination of different strain rates. The benchmark tests in Group IV are used to estimate the creep-fatigue life of steel; the results will be published in a separate paper.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

Construction of a control system for disturbance rejection using a dual observer

A well‐known control system which can reduce the adverse effects of disturbances is a disturbance observer. However, in many cases of mechanical systems, system disturbances which do not satisfy the matching condition may be imposed. Therefore, it may be difficult to reduce the adverse effects of the disturbances by the traditional disturbance observer. In this paper, a method of control system synthesis for disturbance rejection using a dual observer is proposed. This method is based on the zeroing induced by the disturbance localization problem. This problem may be solved by dividing the state space into observable subspace and unobservable subspace. As compared with an H_∞ controller based on perfect observation, the usefulness of the proposed control system for disturbance rejection is demonstrated by numerical simulations for a two‐mass spring system. © 2002 Scripta Technica, Electr Eng Jpn, 138(4): 50–60, 2002; DOI 10.1002/eej.1138     

Spontaneous hemorrhage of an adrenal cortical adenoma causing Cushing''s syndrome

A modified surgical splint for Le Fort I osteotomies with transverse expansion is presented. The splint is made of a transpalatal stainless steel bar with acrylic abutment against the palatal surface of the molar and bicuspid tooth. It is rigid and renders excellent retention. It causes minimal patient discomfort, and oral hygiene is hardly compromised.     

Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

Hybrid verrucous squamous cell carcinoma of sinonasal tract: a case report

Verrucous carcinoma is a variant of squamous cell carcinoma and should be distinguished from benign papilloma and well-differentiated nonverrucous squamous cell carcinoma. It is rare tumor of the sinonasal tract. Occasionally, conventional squamous cell carcinomatous components may be seen in verrucous carcinoma. This entity is called a hybrid verrucous squamous cell carcinoma. We report a case of hybrid verrucous squamous cell carcinoma occurring in the nasal cavity and paranasal sinus of a 67-year-old male. The removed mass shows the typical feature of verrucous carcinoma, but focally conventional squamous cell carcinomatous area is also noted. The treatment of this case follows verrucous carcinoma, but close follow up is mandatory because it may potentially spread to regional lymph nodes in contrast to pure form of verrucous carcinoma.     

Sensitivity of an anadically oxidized aluminium film on a surface acoustic wave sensor to humidity

The sensitivity, transient response and sensitivity mechanism of a surface acoustic wave humidity sensor using porous anodically oxidized aluminium (alumina) films as mechanical interfaces have been studied theoretically and experimentally. It is found that the sensitivity of alumina films of 1.0 μm thickness is -0.034 m/(s %RH) and is the same order as that of polyimide films. The transient response of alumina films to humidity is about one order faster than that of polyimide films. For the sensitivity mechanism, the phase-velocity change is attributed to the mechanical perturbation caused by the absorption of water molecules. The equivalent density change of alumina films between 0 and 100%RH is about 0.7%. In addition, the actual stiffness constants of alumina films are two orders less than those of bulk alumina.     

Effect of Ca2+ and Mg2+ ions on the sintering and spectroscopic properties of cr-doped yttrium aluminum garnet ceramics

In this work, we investigated the effects of Ca²⁺ and Mg²⁺ ions and annealing temperature on the spectroscopic parameters of chromium-doped yttrium aluminum garnet ceramics (Cr:YAG). Samples were obtained with either a separate or a simultaneous addition of calcium and magnesium oxides. To achieve this, aqueous suspensions were prepared using Y₂O₃, Al₂O₃, Cr₂O₃, MgO, and CaO high-purity powders as raw materials. The obtained suspensions were freeze-granulated, pressed into pellets, debinded, and subjected to reactive sintering in vacuum at 1715°C for 6 h. Each material was annealed in air with temperatures between 1300 and 1700°C. Samples were also compared to Cr:YAG ceramics with the addition of silica as a sintering aid. All the materials obtained were then exposed to 445 nm excitation, and emission spectra in the visible and infrared wavelengths were recorded. The results showed that the emission spectra of Cr:YAG ceramics varied according to the annealing conditions: as-sintered samples exhibited strong emissions of around 680 nm and, after air annealing, of around 1400 nm. This phenomenon is attributed to the Cr³⁺→Cr⁴⁺ transition. Samples doped solely with MgO exhibited the highest emission intensity in the infrared region. Thus, Mg²⁺ ions provided the best conversion efficiency of chromium ions.     

Removal of nonionic surfactant by systems based on chloromethylated polystyrene–poly(ethylene glycol)

For the purpose of obtaining compounds which can remove nonionic surfactants in water, chloromethylated polystyrene (CMPS) was allowed to react with triethylene glycol monomethyl ether (3EGMME), tetraethylene glycol (4EG), poly(ethylene glycol) (PEG) 200, 400, 600, 1000, and 1500. The amount of PEG groups combined with CMPS decreased with an increase in the molecular weight of PEG. The ability of the product to remove polyethylene glycol mono-p-nonyl phenyl ether (NP, n = 10), a nonionic surfactant, solutes in water was greater in the product with PEG of greater MW than that with PEG of smaller MW, and in the product with more PEG groups (mol/g prod.) than in that with less PEG groups. The removal behavior of the products conformed to Freundlich's adsorption formula. Constants of the formula, the effect of temperature on the constants, the effect of combined PEG groups on the removed amount, and the removal manner were studied.