Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.     

Quasi-optical waveguide-mode converters using a pair of phase correction mirrors

This paper describes a quasi-optical method for the conversion of modes transmitted through highly oversized circular waveguides. A waveguide-mode is radiated once from a waveguide cut in the form of a radiation beam, which is then properly shaped by two curved mirrors and directed back into the waveguide. The curved mirror shapes are iteratively and automatically determined for given propagation distances using the design technique for phase correction mirrors. The proposed method gives favorable results in designing a waveguide expander/reducer, a TE₀₁-TE₀₂ mode converter, and a TE₀₁-HE₁₁ mode converter.     

Effect of grain size on creep of Ti-53.4mol%Al intermetallics at 1100 K

Constant stress creep under compression stress, 100 to 316 MPa, at 1100 K was investigated on single-phase TiAl intermetallics. The material was ingot-cast, isothermally forged, and then annealed to produce stable equi-axed grain structures, whose average grain diameters were 25, 42 and 70m. Creep curves were very similar among the three specimens with different grain diameters and the creep rates at a given strain, as well as the minimum creep rates, depended little on grain size. Two regimes were observed on the stress dependence of the minimum creep rate. The stress exponent under high stresses was about 4.5, independent of grain size. Under stresses lower than about 150 MPa it became about 8.     

An Application of Silica‐Based Monolithic Membrane Emulsification Technique for Easy and Efficient Preparation of Uniformly Sized Polymer Particles

Summary: Uniformly sized polymer particles were prepared by an emulsification and polymerization technique utilizing a silica monolithic membrane, namely the “silica monolithic membrane emulsification technique”. In this paper, we utilized silica monolithic membrane as a device for the preparation of uniformly sized polymer particles. A mixture of monomers, diluents and oil‐soluble initiator was emulsified into a continuous medium through the silica monolithic membrane and polymerized. The particles obtained had a higher size uniformity than that of particles prepared by previously reported membrane emulsification techniques, such as the Shirasu Porous Glass (SPG) emulsification technique. Through the silica monolithic membrane emulsification technique, we could prepare particles having availability as a possible packing material for solid‐phase extraction (SPE) and high performance liquid chromatography (HPLC).

SEM photograph of silica particles prepared through capillary plate membrane.     

Differences between corrosion products formed on copper exposed in Tokyo in summer and winter

We analyzed the copper corrosion products that formed during a month in summer and a month in winter at three sites in Tokyo using several analytical techniques. The X-ray diffraction patterns revealed that cuprite Cu₂O and posnjakite Cu₄SO₄(OH)₆·H₂O formed on copper exposed in summer. By contrast, only cuprite was found in winter exposed copper. The X-ray fluorescence results indicated that the amounts of sulfur and chlorine on the copper plates exposed in summer were much greater than those in winter. This could be explained by the change in particulate sulfate and sea salt concentrations. Depth profiling analysis by Auger electron spectroscopy revealed that the oxide layer formed in summer was thicker than that in winter. This difference in oxide layer thickness could have been due to the differences in temperature, relative humidity, and the amount of sulfur and chlorine on the copper plate.     

玻璃纤维/大麻纤维增强聚丙烯混杂复合材料的力学性能和断裂特征(英文)

目前在土木工程,建筑,汽车等领域里使用的复合材料中,玻璃纤维是用量最大的增强材料。由于保护地球环境的呼声日趋高涨,天然纤维被期待着代替源于石油而且再利用困难的玻璃纤维,成为绿色复合材料的必要材料之一。本文通过注射成型工艺制作了玻璃短纤维,大麻短纤维以及混杂型纤维增强复合材料,并在拉伸实验中应用两种不同频率的声发射技术检测了拉伸断裂特性。实验发现,随着大麻纤维的加入和混杂复合材料绿色度的增加,复合材料的拉伸弹性模量随之线性增大,而拉伸强度基本保持不变。当大麻纤维的含量超过20wt%的时候,拉伸强度开始降低。在不同频率的声发射实验中,混杂型复合材料的声发射事件的产生都比单一纤维增强型复合材料要来的晚,也就是说,纤维的混杂有助于推迟微裂纹的产生。     

Research and Development of the Coprecipitation Process for Lanthanum Germanate Oxyapatite

Although lanthanum germanate oxyapatite (La–Ge–O) has shown good potential for use as a solid electrolyte in energy storage applications, its synthesis has been challenging by either solid‐ or solution‐state methods. In this study, a new synthesis of La–Ge–O was developed through a coprecipitation technique, in which a highly concentrated homogeneous aqueous solution of La and Ge was prepared from aqueous ammonium germanate and lanthanum nitrate solutions with the addition of dilute nitric acid. Several precipitates were formed by pH manipulation, including an amorphous material obtained at pH > 3. Compared to the individual precipitation behaviors of the parent compounds, the amorphous precipitate was formed only from the aqueous two‐component mixture, and appeared to contain both metals. This material was transformed into crystalline mixtures upon heating at 1273 K. The crystalline phases were La₂Ge₃O₉ and hexagonal‐type GeO₂ when the precipitate was formed below pH 8, and the La–Ge–O and La₂Ge₂O₇ phases when the precipitate was formed around pH 8. Product formation from the coprecipitate was discussed based on X‐ray diffraction and thermal analyses. The improved availability of La–Ge–O will allow more extensive investigations of its useful properties.     

Sol–Gel‐Derived High‐Performance Stacked Transparent Conductive Oxide Thin Films

Single‐ and multi‐layer transparent conductive oxide (TCO) thin films exhibiting high performance, good packing density and low surface/interface roughness are deposited on silica glass substrates by the sol–gel method. The crystal and microstructural properties of the TCO thin films are evaluated as an alternate to films prepared by ultra‐high vacuum deposition. Tin‐doped indium oxide (ITO) thin films produced using a two‐step drying process showed low surface roughness because of dense packing structure not only horizontal but also vertical directions. As a result, electrical conductivity, carrier concentration, carrier mobility, and optical transmittance of 2.3 × 10³ S/cm, 8 × 10²⁰ cm^?3, 18 cm²/Vs, and over 98% at 500 nm, respectively, were achieved. A multilayer ZnO/ITO stacked structure was also fabricated using the sol–gel process. Our findings suggest that solution‐based methods show promise as an alternative to existing ultra‐high vacuum methods to fabricate TCO thin films.     

Fracture and acoustic emission characteristics of glass fiber reinforced plastics panels for hot water

This study deals with the fracture process and acoustic emission (AE) characteristics of a randomly oriented E-glass fiber mat reinforcement with a crosslinked polyester. These panels were evaluated after they were immersed in hot water. The fiber volume content of the panel was 19%. Glass fiber reinforced plastics (GFRP) panels wer immersed in water at 81°C. Bending and AE monitoring tests were Performed and after bending, the cross-section of the specimen was observed by an optical microscope and SEM. The influence of degradation, due to water immersion, on the changes of fracture process of GFRP is discussed. The dominant fracture mode of the virgin specimen was matrix cracks, whereas that of the immersed specimen was debondings at the fiber bundle/matrix and fiber/matrix interfaces. This change was caused by reduction of the bonding strength at the interface. The scale of fracture can be estimated by both AE amplitude and AE energy and this estimation method was used to estimate the fracture mode changes of GFRP panels immersed in hot water.