Carbonization of coals into anisotropic cokes: 7. Copreheat-treatment under short contact-time conditions at high temperature

The copreheat-treatment of non-fusible and slightly fusible coals with A240 and hydrogenated A240 under high temperature-short contact-time conditions around 500 °C has been examined in an attempt to produce a formed coke with better anisotropic development. These conditions shortened the copreheat-treatment time and provided better anisotropic development in the resultant coke after carbonization. Effectiveness of short contact-time has been discussed in terms of the extent of depolymerization of coal molecules suitable for anisotropic development, this being related to coal liquefaction under similar conditions.     

Repulsive Flux Pinning Force in NbTi/Nb Superconductor/Superconductor Multilayers

Flux pinning characteristics have been investigated for the Nb _x Ti_100-x /Nb(x = 65, 50 and 28) and Nb ₂₈ Ti ₇₂/Nb ₆₅ Ti ₃₅ superconductor(S)/superconductor(S^′) multilayers. The maximum of the pinning force F _{p⊥ max} perpendicular to the layer plane as a function of the structure modulation length λ has a peak in the quasi-two-dimensional region (λ～20 nm). The maximum. values of the F _{p⊥ max} versus λ curve are proportional to the difference of the GL coherence length (ξ _GL ) between the superconductive sublayers S and S^′. The results suggest that the large F _{p⊥ max} in the S/S^′ multilayer is caused by the repulsive pinning force due to Nb layers with larger ξ _GL .     

Coating of hydroxyapatite on metal plates using thermal dissociation of calcium-EDTA chelate in phosphate solutions under hydrothermal conditions

Coating of hydroxyapatite on various metal plates was carried out by a homogeneous precipitation technique using hydrothermal reactions in Ca(edta)^2-–NaH₂PO₄ at 140–200°C and pH 3.4–10.0. Hydroxyapatite films were formed on the surface of the iron plates in solutions at an initial pH above 4.7, whereas aggregates consisting of needle-like hydroxyapatite crystal radiating from a point in the form of flower deposited as islands on the surface of aluminum, copper and titanium plates. The upper part of the film formed on the surface of the iron plates consisted of needle-like hydroxyapatite particles whereas the bottom of the film consisted of spherical hydroxyapatite particles. The length of the needle-like hydroxyapatite particles increased with decreasing concentration of Ca(edta)^2-.     

Effects of Particle Size of Bulk Drug and food on the Bioavailability of U-78875 in Dogs

The effects of particle size and food on the absolute bioavailability of U-78875 in dogs after oral administration of either a suspension or tablet dosage form were investigated. A reduction of particle size caused a significant increase in bioavailability along with an increase in dissolution rate. Additionally, both suspension and tablet dosage forms administered after food caused an increase in bioavailability. Thus, to accelerate drug dissolution, a reduction of U-78875 particle size from the unmilled state is important for the optimization of formulation compositions. To increase the bioavailability of U-78875, postprandial dosing should be considered.     

Effect of 8 MeV electron irradiation on electrical properties of CuInSe2 thin films

Radiation damages due to 8 MeV electron irradiation in electrical properties of CuInSe₂ thin films have been investigated. The n-type CuInSe₂ films in which the carrier concentration was about 3×10¹⁶ cm⁻³, were epitaxially grown on a GaAs(0 0 1) substrate by RF diode sputtering. No significant change in the electrical properties was observed under the electron fluence <3×10¹⁶ e cm⁻². As the electron fluence exceeded 10¹⁷ e cm⁻², both the carrier concentration and Hall mobility slightly decreased. The carrier removal rate was estimated to be about 0.8 cm⁻¹, which is slightly lower than that of III–V compound materials.     

Current collecting efficiency of micro tubular SOFCs

In this study, current collecting efficiency of the micro tubular solid oxide fuel cell (SOFC) was estimated to determine optimum size of the micro tubular SOFC. Two models for collecting current from single terminal (ST) and double terminal (DT) of anode tube were proposed and used to calculate the current collecting efficiency as functions of anode thickness, tube length and operating temperature. It was shown that design of the cell geometry and current correcting method are significantly important to achieve high performance micro tubular SOFC stacks. The efficiency loss estimated from the DT model was about 2–4-fold lower than those of obtained from the ST model. The DT model was shown to be more effective for higher operating temperature and the tube length.     

Adsorption of urea,creatinine, and uric acid from three solution types using spherical activated carbon and its recyclability

In this paper, we propose that the urinary toxins from the wastewater be adsorbed on an adsorbent such as spherical activated carbon and the latter be regenerated by subjecting it to high temperatures to recycle activated carbon and also to recycle the water used in dialysis. We studied the adsorption of artificial waste dialysate, which is a mixed solution of urea, creatinine, and uric acid, and the separate solutions for each of these and found that their extents of adsorption onto the spherical activated carbon material were nearly identical. The amount of adsorption was approximately 1.4 mg·g^-1 for urea, 18 mg·g^-1 for creatinine, and 20 mg·g^-1 for uric acid. The urea, creatinine, and uric acid adsorbed onto the spherical activated carbon decomposed on heat treatment at 500℃, and the adsorption capacity of the spherical activated carbon was regenerated. Our study successfully demonstrated that the spherical activated carbon can be recycled in the waste dialysate treatment process.     

Thermal strain of high strength polyethylene fiber in low temperature

High strength polyethylene fiber (Toyobo, Dyneema® fiber: hereinafter abbreviated to DF) has a negative thermal expansion coefficient. Relation between fiber structure and thermal strain of DF used as reinforcement of DF reinforced plastic (DFRP) for cryogenic use was investigated. The crystallinities and orientation angles of several kinds of polyethylene fibers having different modulus from 15 to 134Gpa (herein after abbreviated to DFs) were measured by NMR and X‐ray. We obtained the parameters of the mechanical series‐parallel model composed of crystal and amorphous by crystallinity and modulus. Thermal expansion coefficients of DFs were estimated by mechanical series‐parallel model. All DFs having different modulus showed negative thermal expansion coefficients in the temperature range from 180 to 300K, and absolute values of those markedly increased by increasing tensile modulus of DF. The estimated thermal expansion coefficients showed negative values, and thermal strains showed a similar curve to observed ones mostly. Average thermal expansion coefficients in the temperature range from 180 to 300K estimated by mechanical model agreed with the observed ones. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2918–2925, 2004     

Determination of hydroperoxides and structures by high-performance liquid chromatography with post-column detection with diphenyl-1-pyrenylphosphine

A high-performance liquid chromatographic method, using post-column detection with diphenyl-1-pyrenyl-phosphine (DPPP), was developed for the quantitative and qualitative determination of isomeric lipid hydroperoxides (OOH). The OOH eluted from a normal-phase column were passed through a photodiode array detector and then mixed with DPPP solution in a reaction coil heated at 80°C. DPPP oxide formed by the reaction with OOH was determined by monitoring the fluorescence intensity at 380 nm and excitation at 352 nm. The conjugated diene OOH (13-cis, trans- and 9-cis, trans-OOH) and nonconjugated OOH (12-cis-trans- and 10-cis, trans-OOH) from photosensitized oxidation of methyl linoleate were determined in a molar ratio of 31∶29∶19∶21, respectively. However, only the two conjugated hydroperoxides were detected by ultraviolet absorption at 234 nm. Further applications were carried out for the determination of OOH of methyl oleate and methyl linolenate. This method proved to be useful for the determination of the OOH containing both conjugated and nonconjugated diene structures.