Heat transfer enhancement by Marangoni convection in the NH3–H2O absorption process

The objectives of this paper are to quantify the effect of Marangini convection on the absorption performance for the ammonia–water absorption process, and to visualize Marangoni convection that is induced by adding a heat transfer additive, n-octanol. A real-time single-wavelength holographic interferometer is used for the visualization using a He–Ne gas laser. The interface temperature is always the highest due to the absorption heat release near the interface. It was found that the thermal boundary layer (TBL) increased faster than the diffusion boundary layer (DBL), and the DBL thickness increased by adding the heat transfer additive. At 5 s after absorption started, the DBL thickness for 5 mass% NH₃ without and with the heat transfer additive was 3.0 and 4.5 mm, respectively. Marangoni convection was observed near the interface only in the cases with heat transfer additive. The Marangoni convection was very strong just after the absorption started and it weakened as time elapsed. It was concluded that the absorption performance could be improved by increasing the absorption driving potential (x_vb−x_vi) and by increasing the heat transfer additive concentration. The absorption heat transfer was enhanced as high as 3.0–4.6 times by adding the heat transfer additive that generated Marangoni convection.     

Radiative ignition mechanism of solid fuels

Transmittance of external radiation from a CO₂ laser through a boundary layer of decomposition products over a vertical sample surface is measured during the ignition period. The results indicate that there is significant absorption of the external radiation for PMMA, and a lesser but still not negligible amount, for red oak. An increase in gas phase temperature over surface temperature is observed over much of the ignition interval. Using the experimentally measured incident flux at the sample surface, surface temperature history was calculated from a model that included re-radiation and convection losses from the surface, endothermic decomposition and conduction into the material. The results confirm the significant effect of gas phase absorption on surface temperature. Steady-state-derived surface regression rate expression was used for PMMA in this model. The results raise questions about the validity of such data for the dynamic heating conditions during the ignition period. Further studies needed to understand the radiative ignition mechanism are identified.     

Hydrothermal upgrading of wood biomass: Influence of the addition of K2CO3 and cellulose/lignin ratio

The hydrothermal treatment of two different wood biomass samples such as cherry (hard wood) and cypress (soft wood), whose composition is different i.e. lignin, cellulose and hemicellulose were performed at 280 °C for 15 min with aq. K₂CO₃ with different concentrations (0–1 M). The soft wood biomass contains higher lignin content than hard wood biomass. The cellulose rich cherry wood biomass produced higher proportion of acetic acid than cypress. The lignin rich cypress produced the hydrocarbons with major portion of phenolic hydrocarbons and derivatives than cherry. The total oil yields from both cherry and cypress wood biomass produced 50 wt% of liquid hydrocarbons at 280 °C for 15 min with 0.5 M K₂CO₃ solution. The volatility distribution of liquid hydrocarbons showed the characteristic features of soft and hard wood biomasses.     

The elimination of hepatitis B virus infection: changing seroepidemiology of hepatitis A and B virus infection in Okinawa, Japan over a 26-year period

Serial changes in hepatitis A virus (HAV) and B virus (HBV) markers were determined from 1970 to 1996 in healthy Japanese residents of a rural area of Okinawa, Japan. All 190 serum samples taken in 1970, 791 in 1980, 708 in 1988, and 523 in 1996 from residents 0 to more than 60 years of age were tested for antibody to HAV (anti-HAV), antibody to hepatitis B core antigen (anti-HBc), and hepatitis B surface antigen (HBsAg). The age-adjusted prevalences of anti-HAV and anti-HBc decreased significantly from 83.9% and 74.9%, respectively, in 1970 to 39.7% and 36.6%, respectively, in 1996. In residents < or = 29 years of age, the prevalences of anti-HAV and anti-HBc decreased significantly from 65.3% and 83.8%, respectively, in 1970 to 0.7% and 8.2%, respectively, in 1996. The age-adjusted HBsAg prevalence decreased significantly from 8.2% in 1980 to 4.1% in 1988. These results indicate that exposure to HAV and HBV infections among Okinawa residents less than 29 years of age is decreasing, probably because of improvements in socioeconomic conditions since 1970. Infection with HBV may be eliminated there in the near future.     

INFLUENCE OF DESIGN AND OPERATING CONDITIONS ON THE SYSTEM PERFORMANCE OF A TWO-STAGE ADSORPTION CHILLER

This article aims at clarifying the possible design and operating conditions for silica gel-water adsorption refrigeration cycles driven by near-ambient temperature waste heat sources (between 45 and 75°C) with relatively small regenerating temperature lifts (15 to 45 K). A two-stage silica gel-water advanced adsorption chiller is introduced and a simulation model of the chiller was developed to analyze the influence of operating and design conditions on the system performance (coefficient of performance, COP, and cooling capacity). It was hypothesized that the proposed chiller can be driven by low temperature waste heat at 55°C to produce effective cooling. Simulation results show that the operating conditions such as cycle time and hot and cooling water inlet temperature have an influential effect on cooling capacity and COP. COP is proportional to cycle time and heat transfer coefficient as well as inversely proportional to the cooling water inlet temperature, while there are optimum values of hot water temperature and silica gel weight for maximum COP. Cooling capacity mainly improves with the addition of silica gel weight and decreases as cooling water temperature increases. Simulation results also revealed that the system performance can be improved significantly by setting the design and operating conditions optimally.     

Tribological Characteristics of SiC Ceramics in High-Temperature and High-Pressure Water

The effects of temperature and sliding speed on the tribological behavior of a SiC ceramic by sliding on the same material in deoxygenated water were investigated from room temperature to 300°C under the corresponding saturated vapor pressures. The friction coefficient and specific wear rates of both plates and disks increased at elevated temperatures at all sliding speeds, but decreased with increasing sliding speed at 120° and 300°C. Fine mirrorlike worn surfaces were observed without wear debris under all sliding conditions. The wear mechanism appears to consist of hydrothermal oxidation of SiC and dissolution of reaction products such as silica.     

Plasma developable photoresist containing electronic excitation energy quenching system

A dry developable negative working resist composition comprised of poly(methyl isopropenyl ketone) (PMIPK) and 4-methyl-2,6-di(4′-azido-benzylidene) cyclohexanone-1 was examined. The main photochemical product formed in the resist pattern was found to be a secondary amine which crosslinks PMIPK. Post-annealing forms a hydrogen-bonded product which shows a powerful electronic excitation energy quenching effect. The quencher is more powerful than the aromatic compound arising from the azide by post-annealing only. The residual resist thickness of the negative pattern is about 80 percent of the initial thickness of the coating in spite of all the azide compound remaining in the resist coating. The obtained dry developed resist pattern has a high dry etch resistance. Etchings of Si and SiO₂ were performed by plasma and reactive ion etching, respectively.     

Thermal and flammability properties of a silica–poly(methylmethacrylate) nanocomposite

PMMA, poly(metheylmethacrylate), nanocomposites were made by in situ radical polymerization of MMA, methylmethacrylate, with colloidal silica (ca. 12 nm) to study the effects of nanoscale silica particles on the physical properties and flammability properties of PMMA. Transparent samples resulted and the dispersity of the particles was examined by transmission electron microscopy and atomic force microscopy. The addition of nanosilica particles (13% by mass) did not significantly change the thermal stability, but it made a small improvement in modulus, and it reduced the peak heat release rate roughly 50%. Last, the flame‐retardant mechanism provided by the addition of nanosilica particles in PMMA is discussed. Published 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2072–2078, 2003     

Mass recovery adsorption refrigeration cycle—improving cooling capacity

The study investigates the performance of two-bed, silica gel-water adsorption refrigeration cycle with mass recovery process. The cycle with mass recovery can be driven by the relatively low temperature heat source. In an adsorption refrigeration cycle, the pressures in adsorber and desorber are different. The chiller with mass recovery process utilizes the pressure difference to enhance the refrigerant mass circulation. Cooling capacity and coefficient of performance (COP) were calculated by cycle simulation computer program to analyze the influences of operating conditions. The mass recovery cycle was compared with conventional cycle such as the single stage adsorption cycle in terms of cooling capacity and COP. The results show that the cooling capacity of mass recovery cycle is superior to that of conventional cycle and the mass recovery process is more effective for low regenerating temperature.