AFM observation of polyethylene single crystals: selective handedness of screw dislocations in a chair type

The three-dimensional morphology of polyethylene single crystals grown from dilute solution has been examined by atomic force microscopy. Single crystals were deposited on a soft ground of aqueous solution of poly(vinyl alcohol) (PVA) to avoid the collapse of thin lamellar crystals with thickness of 10 nm. The observation of single crystals on dried PVA clarifies the morphology of a chair type crystal as well as well-known hollow pyramidal type. It has been confirmed that the screw dislocations in the chair type follow a selection rule of the handedness in a manner to relieve the distortion in the chair type.     

Studies on chitin. IX. Crosslinking of water-soluble chitin and evaluation of the products as adsorbents for cupric ion

Water-soluble chitin was successfully crosslinked to varying extents with glutaraldehyde in homogeneous aqueous solutions to improve the properties as an adsorbent for metal cations, and the effects of crosslinking were discussed. Complete insolubilization was achieved with the fivefold excess aldehyde, but, in terms of adsorptivity of Cu²⁺, the chitin crosslinked at an aldehyde/amino group ratio of 1.0 was found to exhibit remarkable capacity and was much superior to others. The desorption of Cu²⁺ from the adsorption complex was also attained effectively at pH 2.0. These results indicated that the loose crosslinking was quite simple and efficient to produce high capacity adsorbents for practical use. Thermal behavior of the crosslinked chitin was examined by TMA and TGA; a softening phenomenon was observed at 145°C.     

Evaluation of inelastic constitutive models under plasticity-creep interaction for steel at 600°C

Uniaxial tests to identify plasticity-creep interaction in steel at 600°C were carried out as the Benchmark Project by the Subcommittee on Inelastic Analysis and Life Prediction, JSMS. The purpose of this paper is to present recent experimental data and predictions of constitutive models obtained in the project. Ten types of constitutive models were utilized to compare analytical predictions to sixteen benchmark experiments which are grouped into four categories: (I) tensile and creep tests under monotonic loading, (II) mixed mode tests under plastic and creep loading, (III) ratcheting deformation tests under program loads, and (IV) cyclic deformation tests under the combination of different strain rates. The benchmark tests in Group IV are used to estimate the creep-fatigue life of steel; the results will be published in a separate paper.     

Real-time measurement of pointing action by using DSP

This paper presents an approach of measuring in real-time the vector of finger that is pointing to an object. DSP is used in the operation processing unit in order to do the real-time processing. The steps include the extraction of flesh-colored regions from an image, the labeling of the flesh-colored regions, and the detection of two characteristic positions on the finger so that the direction that the finger is pointing at will be calculated. The entire process takes about 29 msec, which makes it possible to have the frame rate of 34 fps. With this frame rate, this measurement approach is considered real-time and promising to be merged into other application systems. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Stabilization of inter-area and/or oscillatory modes in large-scale power system by voltage impedance power system (VIPS) apparatus based on decentralized control scheme

New technologies such as power electronics have made it possible to change continuously the impedance of a power system not only to control power flow but also to enhance stability. A power system incorporating a variable impedance apparatus such as a variable series capacitor (VSrC) and high-speed phase shifter (HSPS) is called VIPS (Variable Impedance Power System) by the authors. This paper proposes a novel control method of VIPS apparatus such as VSrC and HSPS installed at an interconnecting point for stabilizing inter-area unstable and/or oscillatory modes. The proposed design method of the control system is a kind of hierarchical decentralized control method of a large-scale power system based on a Lyapunov function. Under the proposed control scheme, each subsystem can be stabilized independently by local controllers such as AVR, speed governor and PSS, and then the whole interconnected system can be stabilized by VIPS apparatus taking into account interactions between subsystems. The effectiveness and robustness of the VIPS apparatus control are shown by numerical examples with model systems including a large-scale power system.     

Three-dimensional display of the bronchi using helical CT

The purpose of this study was to evaluate the clinical usefulness of three-dimensional (3D) images of the bronchi obtained using helical CT. Thirteen patients with lung cancer, one with tracheal diverticulum, and one with bronchial amyloidosis were examined. The CT scanner employed was the Toshiba Xforce. The helical CT scan cycle consisted of 20 continuous rotations, each requiring 1.5 sec, for a total scanning time of 30 sec. Scans were obtained using a 5-mm X-ray beam width, a 5-mm/1.5 sec couchtop sliding speed, and a 2-mm reconstruction interval. 3D images were reconstructed using a CEMAX VIPstation. The optimal lower and upper threshold CT values for 3D images of the bronchi were -650 and -100 HU, respectively, and 3D images clearly depicted endobronchial lesions. Cartilage crescents were also demonstrated, but longitudinal and circular mucosal folds could not be visualized. In conclusion, 3D images of the bronchi acquired using helical CT were useful in evaluating endobronchial lesions.     

The master curve and the constitutive equation for creep deformation and fracture for Cr-Mo-V steel throughout smooth,notched and precracked specimens

It has been shown experimentally that the master curve for creep deformation versus the ratio of time to fracture time, can be obtained for smooth, notched and precracked specimens of Cr-Mo-V steel, a high-temperature ductile material. A simple unified constitutive equation, i.e. a master curve equation, has been proposed. It is suggested that there is some correlation between the creep deformation fracture curve and the creep damage size master curve. Although the range of the applicability of methodology might be rather limited, the development of this concept is needed for improved long-term creep lives and for other creep ductile materials.     

Effect of surfactants on phenol removal by the method of polymerization and precipitation catalysed by Coprinus cinereus peroxidase

The removal of phenol by peroxidase‐catalysed polymerization was examined using Coprinus cinereus peroxidase in the presence of surfactants. The non‐ionic surfactants with poly(oxyethene) residues, Triton X‐100, Triton X‐405 and Tween 20, enhanced the phenol removal efficiency at a level similar to high relative molecular mass poly(ethylene glycol) (relative molecular mass 3000). Although the improvement in the removal efficiency was less than that of Triton X‐100, Span 20, sodium lauryl sulfate (SDS) and lauryl trimethylammonium bromide (DTAB) also enhanced the removal efficiency. The requirement of the enzyme for almost 100% removal of 100 mg dm^?3 phenol decreased to one‐fourth by the addition of 30 mg dm^?3 Triton X‐100. Triton X‐100, Triton X‐405, Tween 20 and DTAB could reactivate the enzyme precipitated with the phenol polymer, leading to the restarting of the phenol removal reaction. Copyright © 2003 Society of Chemical Industry     

Excessive closure of the right eye: a new sign of infarction in the territory of the ipsilateral right middle cerebral artery

In right middle cerebral territory infarction a new sign, excessive closure of the right eye ipsilateral to the lesion and mild closure of the left eye on command, was noted. The excessive ipsilateral eye closure was not observed on spontaneous eye closure.     

Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.