Recovery of gold cyanide using inherently conducting polymers

Removal of gold from basic solutions containing [Au(CN)₂]^? has been demonstrated using the inherently conducting polymer polypyrrole. Polymers containing sulfonated aromatic dopants have been found to display a significant ability to remove gold from such solutions. Experiments performed in solutions containing both gold and copper cyanide complexes indicate that the recovery process is not highly selective. However, the polypyrroles used display significantly faster rates of gold recovery than activated carbon. © 2003 Society of Chemical Industry     

An attempt to compare the performance of bioscrubbers and biotrickling filters for degradation of ethyl acetate in gas streams

This study presents a comparison of the efficiency of a bioscrubber and a biotrickling filter (BTF) for the removal of ethyl acetate (EA) vapour from a waste gas stream, under the same operating conditions. The maximum EA elimination capacity achieved in the bioscrubber was 550 g m^?3 h^?1 with removal efficiency higher than 96%. For higher EA loadings the bioscrubber was oxygen limited, which caused incomplete EA biodegradation. When pure oxygen was fed to the bioscrubber at a rate of 0.02 L min^?1, the bioscrubber recovered and could treat higher EA loadings without any oxygen limitation. The BTF achieved EA elimination capacity of 600 g m^?3 h^?1 with removal efficiency higher than 97% and the dissolved oxygen concentration remained substantially higher than in the bioscrubber. However, severe channelling and blockage of the spray nozzle occurred due to the excessive biomass growth. Overall, the bioscrubber system was easier to operate and control than the BTF, while an enhancement of the oxygen mass transfer in the bioscrubber could potentially increase its performance by up to three times. Copyright © 2005 Society of Chemical Industry     

The radiation crosslinking and scission of ethylene-propylene copolymers studied by solid-state nuclear magnetic resonance

Methyl groups from chain scission and H-crosslinks have been identified by solid-state nuclear magnetic resonance in amorphous ethylene-propylene copolymers containing 23 and 36 mole % propylene after γ-irradiation to 10 MGy at 30°C. G (scission) and G (crosslink) values determined from the n.m.r. spectra and by extraction are in agreement, which suggests that the crosslinks are not clustered. This may differ from the situation in polyethylene where there is a substantial crystalline content. G(S). G(X) and the ratio G(S)/G(X) increase with increasing propylene content of the copolymers.     

Kinetic analysis of the crystallization of poly(p-phenylene sulphide)

Growth rates of spherulites were measured in poly(p-phenylene sulphide) crystallized from the melt and the quenched glass over the temperature range 100°C–280°C, possibly the most extensive overall range yet reported for any polymer and, as such, most propitious for study of régime III crystallization. For a medium M.wt. polymer, a régime II → III transition was obtained at 208°C using values of transport parameters common to many polymers ($\text{U1 = 1400}\text{cal mol}{}^{\mathrm{?1}}$, T_∞ ? T_g = 30°C) together with experimentally determined values of T⁰_m(315°C) and T_g(92°C). Under these conditions, the régime III/II slope ratio was found to be 2.07 (i.e. only 3.5% higher than predicted by régime theory), and reasonable estimates of surface free energies and of the work of chain folding were obtained. Other choices of the transport terms, including WLF and zero values, did not allow successful kinetic analyses. Although a régime I → II transition is predicted to occur at the high-temperature end of our growth-rate data, we found no experimental evidence for it. For a low M.wt. polymer, our analysis showed that régime III kinetics is obeyed at low temperatures, while at higher ones there is a continuous departure from that behaviour without, however, full attainment of régime II kinetics.     

Implementing Information Systems: Some Practical Advice and a Richer Model

Recent research suggests that implementing information systems presents considerable difficulties and that many implementations are total or partial failures. This paper argues that what both practitioners and students require are richer and more acceptable models of information systems implementation. Accordingly, case study data concerning the introduction of manufacturing resource planning (MRP II) are used to illustrate five patterns of behaviour (rites) which capture important social actions; and four components of changing psychological orientation. It is argued that appreciation of the rites and psychological developments identified here will support effective change programmes. Guidelines based on our model are provided for practitioners.     

Effects of viscosity on the bitterness and astringency of grape seed tannin

To examine the separate effects of viscosity and sweetness on astringency, aqueous solutions of grape seed tannin (GST) were thickened with carboxymethyl cellulose (CMC) from 2 to 45 cP (experiment 1) or sweetened with 0 to 1.8 g/L aspartame (experiment 2). Trained subjects continuously rated astringency and bitterness in duplicate. Subjects were categorized by the salivary flow induced by citric acid and ability to taste n-propyl thiouracil (PROP). In experiment 1, maximum intensity and total duration of astringency were significantly decreased as viscosity rose, although time to maximum intensity of astringency was not affected. Maximum intensity and total duration of bitterness were not significantly affected by increasing viscosity; however, the onset of bitterness was significantly delayed. In experiment 2, increasing sweetness had no affect on any astringency parameter, although maximum intensity of bitterness was significantly decreased. Neither PROP nor salivary flow-status had any effect on perception of bitterness or astringency in either experiment.     

Algorithms for Scheduling Multi-Level Just-In-Time Production Systems

Many companies are using Just-In-Time (JIT) control systems in their mixed-model multi-level production facilities. When scheduling these facilities the most important objective is to keep a constant rate of usage for every part used by the system. In this paper a mathematical model for scheduling these facilities is studied and techniques for determining good schedules are developed. Procedures for solving very large problems are given.