Influence of ZrB2 hard ceramic reinforcement on mechanical and wear properties of aluminum

In this work, the effect of ZrB₂ (0, 5, 10 and 20?vol%) ceramic reinforcement on densification, structure, and properties of mechanically alloyed Al was investigated. The milling of Al-ZrB₂ powder compositions resulted in formation of agglomerates with varied size. In particular, the size of agglomerates was reduced considerably with increased addition of ZrB₂ to Al. Interestingly, the densification of hot pressed Al increased from 96.06% to 99.22% with ZrB₂ addition. The reduction of agglomerates size was attributed to the enhanced densification of Al-ZrB₂ composites. Pure Al showed relatively low hardness (0.94?GPa) and it was improved to 1.78?GPa with the addition of 20?vol% ZrB₂. The mechanical properties have significantly been improved for Al-ZrB₂ composites. Especially Al - 20?vol% ZrB₂ possessed a very high yield strength (529?MPa), compressive strength (630?MPa) and compressive strain of 19.25%. Realization of such a good combination of mechanical properties is the highest ever reported for Al composites so far in the literature. The coefficient of friction (COF) of Al-ZrB₂ varied narrowly between 0.33 and 0.40 after dry sliding wear against steel disc. The wear rate of Al-ZrB₂ composites was within mild wear regime and varied between 98.88?×?10^?6 and 34.66?×?10^?6 mm³/Nm. Among all the compositions, Al - 20?vol% ZrB₂ composite exhibited the lowest wear rate and high wear rate was noted for pure Al. Mild abrasion, tribo-oxidation, third body wear (wear debris) and delamination were the major material removal mechanisms for Al-ZrB₂ composites. Overall the hardness, strength and wear resistance of Al - 20?vol% ZrB₂ composite was improved by 84.3%, 84.3% and 64.2%, respectively when compared to pure Al.     

Mathematical model for computer simulation and control of steelmaking

A dynamic model for computer simulation and control of steelmaking has been developed. It is essentially based on multicomponent mixed transport control theory with the incorporation of energy balance calculations. The model is applicable to both steelmaking in electric furnaces as well as in oxygen steelmaking converters. The adjustable parameters of the model for simulation of oxygen steelmaking are gas evolution rate (G_co). oxygen flux factor (F_o) and emulsification factor (EM). These simulation parameters, when combined with on-line measurement of off-gas composition and temperature, enable complete dynamic control of the process. The model developed is applied, as an example, to an industrially produced heat in a top blown oxygen steelmaking converter and the results of simulation are discussed.     

Deposition of thin film silicon using the pulsed PECVD and HWCVD techniques

We report on the use of pulsed plasma-enhanced chemical vapor deposition (P-PECVD) technique and show that “state-of-the-art” amorphous silicon (a-Si:H) materials and solar cells can be produced at a deposition rate of up to 15 Å/s using a modulation frequency in the range 1–100 kHz. The approach has also been developed to deposit materials and devices onto large area, 30 cm×40 cm, substrates with thickness uniformity (<5%), and gas utilization rate (>25%). We have developed a new “hot wire” chemical vapor deposition (HWCVD) method and report that our new filament material, graphite, has so far shown no appreciable degradation even after deposition of 500 μm of amorphous silicon. We report that this technique can produce “state-of-the-art” a-Si:H and that a solar cell of p/i/n configuration exhibited an initial efficiency approaching 9%. The use of microcrystalline silicon (μc-Si) materials to produce low-cost stable solar cells is gaining considerable attention. We show that both of these techniques can produce thin film μc-Si, dependent on process conditions, with 1 1 1 and/or 2 2 0 orientations and with a grain size of approx. 500 A. Inclusion of these types of materials into a solar cell configuration will be discussed.     

Resource contention in shared-memory multiprocessors: A parameterized performance degradation model

A standard metric conventionally employed to compare the performance of different multiprocessor systems is speedup. Although providing a measure of the improvement in execution speed achievable on a system, this metric does not yield any insight into the factors responsible for limiting the potential improvement in speed. This paper studies the performance degradation in shared-memory multiprocessors as a result of contention for shared-memory resources. A replicate workload framework with a flexible mechanism for workload specification is proposed for measuring performance. Two normalized performance metrics—efficiency and overhead factor—are introduced to quantify the factors limiting performance and facilitate comparison across architectures. Finally, the proposed model is employed to measure and compare the performance of three contemporary shared-memory systems, with special emphasis on the newly released BBN Butterfly-II (TC2000), currently undergoing Beta test.     

INFLUENCE OF DRYING CONDITIONS ON THE FRAGILITY OF CORN KERNELS

A dynamic rcsring dnim war built to study the effects of air temperature, moisture content and grain shape on fragility of the air dried kernels. For drying rares under 0.05 kglkg min. the fragility of kernels could br described empirically as a function of the three experimental parameters.     

STEAM DRYING TECHNOLOGIES: JAPANESE R&D

This report reviews some fundamental and practical aspects of steam drying technologies based mainly on studies published in Japan. Steam drying kinetics, and some industrial technologies particularly for drying of foods, textiles and sludges are reviewed with focus on quality of dried material, drying time, dryer selection and energy recovery from steam dryer exhaust. For energy recovery, heat pump technologies are outlined along with characteristics of different types of steam compressors. A new process is proposed for steam drying; it combines a direct-indirect dryer followed by a direct steam dryer for internal moisture removal.