Modeling the sequential switching shunt series regulator

This letter characterizes, in terms of the bandwidth and limit cycle frequency of its constituent subsystems, the sequential switching shunt series regulator -S/sup 4/R, a high-efficiency, low-mass and volume power cell devised to power the next generation of regulated power buses in telecommunication spacecrafts. Transconductance power source modeling is used to obtain linear and nonlinear models. These are used to establish a design control strategy which involves the dynamic response in large load requirements or at the end of the satellite life. Simulations and experimental results are also given to demonstrate the validity of the model.     

Nonlinear adaptive algorithms for equalisation in mobile satellite communications

This paper considers the equalisation problem in Quadrature Phase-Shift Keying (QPSK) modulated signals which have been distorted by the passage through a transmission channel. The channel is modelled as a Rician fading channel to simulate the behaviour of the transmission channel in the mobile satellite context. The equalisation is treated as the generalisation of the channel behaviour, and some algorithms with the structure of an artificial neural network using the Multilayer Perceptron, Volterra Series and Radial Basis Function are described. Results for the BER performance of typical transversal equalisers, with Square-Root Kalman adaptation algorithm, and algorithms with artificial neural network structure are also reported and evaluated. Improved performance is exhibited by the artificial neural network approaches.     

International collaboration: Will it be keeping alive East European research?

International scientific collaboration is very sensitive to political and economic changes in a country or a geopolitical region. Collaboration in research is reflected by the corresponding coauthorship of the published results which can be analysed with the help of bibliometric methods. Based on data from theScience Citation Index (SCI), the change of annual international coauthorship patterns ofBulgaria, Czechoslovakia, Hungary, Poland andRomania have been analysed for the periods 1981–1985 and 1984–1993, respectively. It is shown that international collaboration was not developing similarly in the countries under study. Whilst scientific communities of Hungary and Poland have already been opening in the early 80s, the international collaboration of the other East-European countries was still dominated by COMECON relations till 1989. As expected, since 1990 an increasing scientific collaboration with highly developed countries can be observed in all five countries. At the same time, scientific collaboration with the former communist countries shows a clear decline. The great share of international co-authorship links is some countries reflect various tendencies part of which are interpreted with the help of a cardiologic model.     

The effect of the addition of chemical materials on the sintering of biomass ash

In this work the use of chemical materials (additives) in order to reduce the biomass ash sintering tendency is investigated. A total of seven additives (kaolin, limestone, lime, dolomite, calcined dolomite, ophite and alumina) and silica utilised as reference material were mixed in different proportions with the ash of five different biomasses, and then a laboratory sintering test was performed on the mixtures to determine the effect of the additives on the sintering. The biomasses studied in this work were: thistle biomass, brassica carinata biomass, barley straw, almond shell and orujillo (olive oil extraction residue). The sintering decrease among the additives was studied using X-ray diffraction.Kaolin, lime, calcined dolomite and ophite are proved to be suitable to reduce the biomass sintering in all the considered cases. Dolomite, limestone and, particularly, the tabular alumina, offer poorer results. The dilution of the biomass ash is considered the main process involved in the decrease of the sintering for most of the additives, with the exception of kaolin whose chemical reactions could be more important than the dilution effect.     

Effect of sodium nitroprusside on compound action potential thresholds in the gerbil cochlea

OBJECTIVE: Trials that do not allow rejection of the null hypothesis of no treatment effect may have had an inappropriate design. Trials are virtually never assessed for correlation between responses to different treatment modalities. METHODS: Using a hypothetical example and several published studies we examine the influence of correlation levels between treatment modalities on the sensitivity of testing. RESULTS: The level of correlation between responses to different treatment modalities is a major determinant of the sensitivity both of crossover and parallel group clinical trials. CONCLUSIONS: It is very relevant to assess a priori correlation levels between responses to the different treatment modalities of a trial. If a negative correlation is anticipated, a crossover design is likely to lack sensitivity. If a positive correlation is anticipated a parallel-group design seems less appropriate, because it would lack the extra sensitivity of accounting for the positive correlation. Both designs would seem suitable for approximately zero correlations (e.g. comparison vs baseline or vs placebo under the assumption that the number of placebo responders is negligible.     

Sensory evaluation of quality and quality differences in slaughtered chickens

A study was carried out with a trained panel for the purpose of determining if modifications produced in slaughtered chickens during the storage period, caused significant organoleptic differences, detectable by the consumer. The products examined corresponded to chickens slaughtered on three consecutive days, stored at 2 degrees C until their evaluation. Qualitative aspects in the raw product were investigated by a score test in which optimum quality is 13 points, as follows: for color (range 3), general appearance (range 5), and presence of defects (range 5). The values obtained were then analyzed through variance and Duncan multiple range test. Simultaneously, taste changes were estimated in fatty and meager meat by the triangular test. Homogeneity between judgements of panel members on both types of meat was statistically established (P = 0.05). The results obtained indicate that at the 0.1% level of significance, two products were identical; a third one proved to be different and of a significantly higher quality at the 5% level. The degree of difference, from slight to moderate, was due to flavor.     

Effect of crystallization on morphology-conductivity relationship in polypyrrole/poly(?-caprolactone) blends

Electrically conducting blends, based on polypyrrole (PPy) as the conductive polymer and poly(?-caprolactone) (PCL) as an insulating polymeric matrix, were prepared by polymerizing pyrrole (Py) in its vapor state inside the PCL matrix. The roles of specific interactions between blend components as well as the crystallization of PCL matrix in the resulting morphology have been analyzed by Fourier-transform infrared spectroscopy (FTIR), thermo-optical analysis (TOA) and atomic force microscopy (AFM). The results indicate that PPy is located within both the intra and interspherulitic regions of the PCL matrix achieving a well-developed connected network. Compared with amorphous matrices, considerable conductivity (around 1 S/cm) was raised with the crystalline PCL matrix with only a relatively low level of the conductive polymer (∼5%) in the blend.     

Extended bisection method for parameter identification of the transient heat conduction equation for thermo-elastic deformations during drilling

A new interdisciplinary approach is discribed to identifying unknown parameters using an extended version of the known interval bisection method. This developed method is based on the use of finite elements for calibrating the simulation calculation. The resulting thermo-elastic deformations which occur in drilling processes with impaired cooling lubrication are to be used as correction values for tool positioning in the NC control. Based on the strong impact on workpiece temperature of machining, a simulation approach is presented for calculating the temperature fields and their thermo-elastic consequences. In addition, methods are presented to correct these effects. This paper particularly deals with the temperature fields of drilling operations. Special attention is paid to the technique employed for iterative numerical determination of the unknown heat flux η _w and heat transfer coefficient \(\bar {\gamma }\) values. Finally, the data obtained from experiments are compared with those achieved by numerical simulation in order to verify the efficiency of simulation and determination of parameters.