Heat propagation in thermally conductive polymers of PA6 and hexagonal boron nitride

Thermally conductive polymers offer new possibilities for the heat dissipation in electric and electronic components, for example, by a three‐dimensional shaping of the heat sinks. To face safety regulations, improved fire performance of those components is required. In contrast to unfilled polymers, those materials exhibit an entirely different thermal behavior. To investigate the flammability, a phosphorus flame retardant was incorporated into thermally conductive composites of polyamide 6 and hexagonal boron nitride. The flame retardant decreased the thermal conductivity only slightly. However, the burning behavior changed significantly, due to a different heat propagation, which was investigated using a thermographic camera. An optimum content of hexagonal boron nitride for a sufficient thermal conductivity and fire performance was found between 20 and 30 vol%. The improvement of the fire performance was due to a faster heat release out of the pyrolysis zone and an earlier decomposition of the flame retardant. For higher contents of hexagonal boron nitride, the heat was spread faster within the part, promoting an earlier ignition and increasing the decomposition rate of the flame retardant.     

Lignin from Annual Plants as Raw Material Source for Flavors and Basic Chemicals

The enzymatic conversion of lignins, possibly in combination with electrochemical oxidation, makes aromatics such as syringol, guaiacol, vanillin and catechol available in the qualities required by the fragrance industry. The lignins were obtained by soda digestion from wheat straw and Miscanthus, characterized and then converted with laccases. The overall yield amounted up to 9 wt % with a product spectrum confined to four substances. Catechol was the major product, with a fraction of ≈75 %. It can easily be isolated by extraction with acetone.     

Bias and temperature dependence of homogeneous hot-electroninjection from silicon into silicon dioxide at low voltages

In this paper, new homogeneous hot-electron injection data at 300 K and 77 K is provided covering applied voltages from well below to well above the Si-SiO₂ barrier height, and a wide range of oxide fields. We found that, in contrast to the MOSFET case, homogeneous injection shows two different regimes for accelerating voltages below and above the barrier height. A simple interpretation of the data is proposed, and supported by Monte Carlo (MC) simulations of the injection experiment. Essentially, the two regimes are the signature of a marked transition between an electron population mostly heated by the electric field, and a tail population created by additional but less efficient energy gain mechanisms, leading to a sharp transition in the carrier distribution function. The details of the bias and temperature dependence of injection are then interpreted as the combined effect of tunneling and carrier distribution. Furthermore, possible implications on MOSFET gate currents are briefly discussed     

Peripheral nerve stimulation by time-varying magnetic fields

PURPOSE: A study was performed to assess the stimulation threshold for healthy adults using sinusoidally oscillating gradients. METHOD: One hundred thirteen healthy adults were examined in the study. ECG and physiological parameters were measured. All measurements were performed of both the head and the abdomen. The subjects were measured in the supine position with the region of interest positioned in the center of the gradient coils. The measurement was performed for three orthogonal, four oblique, and double oblique orientations. RESULTS: No volunteer reported painful, severe stimulation. The mean thresholds for peripheral stimulation in head and body measurement were similar: 85.5% of stimulation during examination of the head and 87.6% during measurements of the abdomen were reported when the y-gradient was used. CONCLUSION: The greatest frequency of reported stimulations occurs when the y-gradient is used. This was confirmed by the results and supports the hypothesis that orthogonal to the y-axis the body has its largest conductive loop, resulting in the strongest peripheral stimulation.     

Initial experiences with the MR "magnitude contrast angiography of the lower extremities

45 patients with occlusive peripheral vascular disease were examined by MR angiography in a retrospective study. A FISP 3D sequence was used by acquiring a rephased and a dephased data set. The individual slices were post-processed by using a maximum-intensity-projection algorithm. The MRA results of the popliteal and tibioperoneal arteries were compared to conventional or digital angiography. In comparing these techniques MR angiography cannot be accepted for pre- and postoperative staging of patients with occlusive peripheral vascular disease. In future new MRA techniques may be useful in postoperative staging of patients with peripheral vascular stenosis.     

Evaluation of NDT methods for detection of prestressing steel damage at post-tensioned concrete structures

For an assessment of the risk potential of existing structures, where in the case of prestressing steel damage the load-bearing capacity could be significantly affected, non-destructive testing techniques which enable reliable evaluation of the condition of the prestressing steels are of utmost importance. During the demolition of a post-tensioned concrete bridge in Berlin where damage of prestressing wires due to hydrogen-induced stress corrosion cracking were found in former investigations, parts of the girders of the bridge superstructure could be taken out. After non-destructive investigations by means of two testing techniques based on magnetic leakage flux measurement and one technique based on electromagnetic resonance measurement, subsequent removal of the concrete cover up to the ducts, opening the ducts and evaluation of the prestressing steels allowed a verification of the results obtained by the NDT methods. From the results it can be concluded that areas with fractures of several wires can be detected by the two techniques based on magnetic leakage flux measurement.