Thermal instability of Bi-Pb-Sr-Ca-Cu-O superconductor around 650δC

Bi_0.85Pb_0.15Sr_0.8CaCu_1.4O _y superconductor was quenched to room temperature after annealing at several temperatures in air. From the initial magnetization curve measurement for the annealed samples, it was found that the volume fraction of superconducting phases of the sample annealed at 650°C greatly decreased. TEM observation revealed that a second phase often appeared in the grain-boundary region for the sample annealed at 700°C. The second phase was identified as Bi₁Pb₂Sr_2.6Ca_1.6O _y by energy dispersive spectroscopy.     

Immunohistochemical localization of advanced glycosylation end products in coronary atheroma and cardiac tissue in diabetes mellitus

Advanced glycosylation end products (AGEs) accumulate on long-lived extracellular matrix proteins and have been implicated in the micro- and macrovascular complications of diabetes mellitus. Within the arterial wall, AGE-modified proteins increase vascular permeability, inactivate nitric oxide activity, and induce the release of growth-promoting cytokines. Recently developed anti-AGE antibodies were used in an immunohistochemical analysis of coronary arteries obtained from type II diabetic and nondiabetic patients. High levels of AGE reactivity were observed within the atherosclerotic plaque present in vessels from selected patients with diabetes. Considered together with the pathological effects of AGEs on vascular wall homeostasis, these data support the role of advanced glycosylation in the rapidly progressive atherosclerosis associated with diabetes mellitus.     

Spectral attenuation measurement for fluoride glass single-mode fibres by Fourier transform techniques

A new spectral attenuation measurement system using a Fourier transform spectrometer is developed. The Fourier transform spectral attenuation measurement (FT-SAM) system makes the signal acquisition time for a wide wave-length range of 1.0?4.2? much shorter than measurement with a conventional dispersive spectral attenuation measurement system. The spectral attenuation for a fluoride glass single-mode fibre, with a minimum loss of 3±1 dB/km at 2.5?m, is measured with this system.     

Effect of Composition on the Oxygen Tracer Diffusion in Transparent Yttrium Aluminium Garnet (YAG) Ceramics

The grain boundary structure and oxygen tracer diffusion in transparent yttrium aluminum garnet (YAG) ceramics varying from 2% excess of Y₂O₃ to 0.5% excess of Al₂O₃ were studied. The characterization of the specimens is as follows: (i) For the Y₂O₃-excess specimen, a second phase (yttrium aluminum perovskite: YAP) containing silicon in the grain boundary was found, (ii) For the Al₂O₃-excess specimen, both aluminum-rich particles (alumina) and a silicon-rich segregant layer were observed in the grain boundary. The volume diffusion of the oxygen tracer is little influenced by the excess composition. In contrast, the grain boundary diffusion of the oxygen tracer is suppressed in the Y₂O₃-excess specimens, compared to Al₂O₃-excess specimens. These differences are thought to result from the chemical reaction between the second phase and the intergranular liquid phase during the sintering.     

Copolymerization of methylmethacrylate on a ball-milled surface of coal at 77 K

The ball-milling of coal with methylmethacrylate monomer was carried out under vacuum at 77 K and at room temperature and in air. The e.s.r. and i.r. spectra of ball-milled material showed that a copolymer of coal and methylmethacrylate was formed on the surfaces of coal created by ball-mining. Oxygen is an inhibitor to this process.     

Synthesis of High-Purity Zirconium Fluoride for Fluoride Glass Fibers by Chemical Vapor Deposition

A technique for synthesizing ultra-high-purity ZrF₄ using chemical vapor deposition in a ZrBr₄–HF system is developed and a purification mechanism is clarified. The Fe concentration in ZrF₄ is evaluated at less than 10 ppb based on analysis of the transmission loss spectrum of a fiber prepared using synthesized ZrF₄. Purification is achieved mainly in a sublimation process of ZrBr₄, and purification efficiency is determined by sublimation temperature and activity of impurities in ZrBr₄. The concentration of transition-metal impurities in ZrF₄, synthesized by chemical vapor deposition in the ZrBr₄–HF system, is expected to be less than 1 ppb.     

E.s.r. study of annealing and melting effects on the molecular motion of spin trapped chain-end radicals located on the polyethylene surface

E.s.r. spectra of chain-end spin labels on the surface of polyethylene powder were obtained for high and low density polyethylene samples at various stages of heat treatment process. The subsequent crystalline structures of the samples were examined with wide angle and small angle X-ray diffraction spectra. The effects of annealing on the motion of the labels were dependent on annealing temperature and the type of the samples. Higher temperature annealing decreased the rotational correlation times (τ_c) and their activation energy in high density polyethylene but did not affect those of low density polyethylene. Melting decreases the values of τ_c and ΔE for both high an low density polyethylene samples. The cause of these decreases were attributed to the changing of the sites of the chain-end labels. The motion of the labels appeared to be influenced by the local segmental motion of the polymer main chains.     

Fundamental characteristics of printed gelatin utilizing micro 3D printer

Gelatin is useful for biofabrication, because it can be used for cell scaffolds and it has unique properties. Therefore, we attempted to fabricate biodevices of gelatin utilizing micro 3D printer which is able to print with high precision. However, it has been difficult to fabricate 3D structure of gelatin utilizing 3D printer, because a printed gelatin droplet on the metal plate electrode would spread before solidification. To clear this problem, we developed a new experimental set-up with a peltier device that can control temperature of the impact point. At an impact point temperature of 80 °C, the spreading of printed gelatin droplets was prevented. Therefore, we were able to print a ball gelatin. In addition, we were able to print a narrower gelatin line than at an impact point temperature of 20 °C.     

Effect of drawing condition on mechanical properties and molecular orientation of self-reinforced poly(lactic acid) screws

Effects of extrusion ratio (ER) during extruding on mechanical properties of poly(lactic acid) (PLA) screws were investigated in terms of shear and twist strength. Shear strength increased by drawing, while twist strength decreased. This might be due to orientation of molecular chains during drawing. In order to evaluate orientation of molecular chains, orientation function in extruded billets was measured as a function of ER. Since orientation function increased with ER, drawing is effective method to improve shear strength of screw, where fibrous structure which was formed during extruding resisted shear stress in cross-section perpendicular to screw axis. Although orientation functions for billet extruded at ER 1.3–4 were equivalent, both strengths changed for the screw extruded at the range of this ER. Infrared spectra suggested transforming from α to β crystal for the billet extruded at the range of this ER. This result suggested that mechanical properties of screw also depended on the crystal forms.