Nonwoven Ni–NiO/carbon fibers for electrochemical water oxidation

The development of technologically efficient anodes for water oxidation is crucial to improve hydrogen production via water splitting. Electrodes based on metallic active sites dispersed in carbon matrices have been shown to be an attractive way to attain this goal. However, challenges remain to prevent catalyst agglomeration that otherwise can result in a decrease of performance over time.In this work, we report an alternative and efficient method to produce nickel-nickel oxide nanoparticles-embedded in carbon nanofibers (Ni–NiO/C), by the solution blow spinning (SBS) process. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses show the carbon nanofibrillar matrix as a robust support, with well-dispersed nickel nanoparticles on the surface. The responses of the linear scanning voltammetry, cyclic voltammetry and electrochemical impedance spectroscopy demonstrate how a small fraction of nickel on the fiber surface (≈1.2–5.3%) is enough to promote substantial improvement in performance (η = 278 and 309 mV vs RHE for 10 mA cm^?2) and a significant turnover frequency (TOF) values of 1.38 (η = 278) and 1.30 s^?1 (η = 309). These promising results are correlated with a large amount of Ni³⁺ present on the fiber surfaces, as identified by X-ray Photoelectron Spectroscopy (XPS). This work provides a low-cost and rapid preparation technique that can be extended for the manufacture of a wide variety of electrodes based on metals supported on carbon nanofibers.     

Synthesis and characterisation of fluorescent pyrene‐end‐capped polylactide fibres

Fluorescent markers are critical for tracking the position and movement of molecules both in vivo and in vitro. Conventionally, synthetic dyes are non‐covalently added to polymers for fluorescent tracking, but often diffuse away. Here we demonstrate, for the first time, a facile method for the synthesis of fluorescent poly(lactic acid) nano‐/microfibres for biomedical applications using solution spin blowing. Pyrene‐end‐capped poly(l ‐lactide) (PLLA) derivatives were synthesised using the ring‐opening polymerisation of l ‐lactide and they were characterised using spectroscopic and thermal analyses. Submicrometre‐sized fluorescent fibres were produced from these PLLA derivatives using solution blow spinning techniques generating polymer blends and core–shell fibres. Such system could be further exploited to incorporate electrically conductive carbon allotropes via the pyrene aromaticity, producing fluorescent and electrically active fibres for in vitro monitoring and electrical stimulation. © 2018 Society of Chemical Industry     

Polyaniline‐modified cellulose nanofibrils as reinforcement of a smart polyurethane

Segmented polyurethanes exhibiting shape memory properties were modified by the addition of polyaniline (PANI)‐coated cellulose nanofibrils (CNFs). The two‐phase structure of the polymer is responsible for the material's ability to ‘remember’ and autonomously recover its original shape after being deformed in response to an external thermal stimulus. PANI was grown on the surface of the CNFs via in situ polymerization. Modified nanocrystals were added to the segmented polyurethane in concentrations ranging from 0 to 15 wt%. The changes in the material properties associated with the percolation of the coated fibrils appear at higher concentrations than previously observed for non‐modified CNFs, which suggests that fibril agglomeration is occurring due to the PANI coating. The shape memory behavior of the composites is maintained at about the same level as that of the unfilled polyurethane only up to 4 wt% of fibrils. At higher concentrations, the rigidity of the nanofibrils as well as their interaction with the hard‐segment phase and the increasing difficulty of dispersing them in the polymer collaborate to produce early breakage of the specimens when stretched at temperatures above the melting point of the soft segments. Copyright © 2010 Society of Chemical Industry     

Structural,Electrical, Mechanical,and Thermal Properties of Electrospun Poly(lactic acid)/Polyaniline Blend Fibers

Conducting electrospun fiber mats based on PLA and PAni blends were obtained with average diameter values between 87 and 1 006 nm with PAni quantities from 0 to 5.6 wt.‐%. Structural characteristics of fiber mats were compared to cast films with the same amount of PAni and studied by SEM, SAXS, and AFM. Thermal properties of fiber mats and cast films were compared by DSC analyses. Mechanical properties of fiber mats were also evaluated. It was found that electrospinning process governs the crystal structure of the fibers and strongly affects fiber properties. New properties of PLA/PAni blends are reported due to the size fiber reduction.

     

Curing behavior of a novolac‐type phenolic resin analyzed by differential scanning calorimetry

Curing of a novolac‐type phenolic resin was studied by DSC. The kinetic analysis was performed by means of the dynamic Ozawa method at heating rates of 5, 10, 15, and 20°C/min. This analysis was used to determine the kinetic parameters of the curing process. The activation energy was found to be 144 kJ/mol. It was found that the Ozawa exponent values decreased with increasing reaction temperature from 3.5 to 1, suggesting a change in the reaction mechanism from microgel growth to diffusion‐controlled reaction. The reaction rate constant was found to range from 123.0 to 33.6 (°C/min)ⁿ. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1678–1682, 2003     

Biodegradable composites based on starch/EVOH/glycerol blends and coconut fibers

Unripe coconut fibers were used as fillers in a biodegradable polymer matrix of starch/ethylene vinyl alcohol (EVOH)/glycerol. The effects of fiber content on the mechanical, thermal, and structural properties were evaluated. The addition of coconut fiber into starch/EVOH/glycerol blends reduced the ductile behavior of the matrix by making the composites more brittle. At low fiber content, blends were more flexible, with higher tensile strength than at higher fiber levels. The temperature at the maximum degradation rate slightly shifted to lower values as fiber content increased. Comparing blends with and without fibers, there was no drastic change in melt temperature of the matrix with increase of fiber content, indicating that fibers did not lead to significant changes in crystalline structure. The micrographs of the tensile fractured specimens showed a large number of holes resulting from fiber pull‐out from the matrix, indicating poor adhesion between fiber and matrix. Although starch alone degraded readily, starch/EVOH/glycerol blends exhibited much slower degradation in compost. Composites produced 24.4–28.8% less CO₂ compared with starch in a closed‐circuit respirometer. Addition of increasing amount of fiber in starch/EVOH/glycerol composite had no impact on its biodegradation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly(lactic acid)/poly(vinyl pyrrolidone) membranes produced by solution blow spinning: Structure,thermal, spectroscopic,and microbial barrier properties

Submicrometric and nanometric poly(lactic acid)/poly(vinyl pyrrolidone) (PLA/PVP) fibrous membranes containing 0, 5, 10, 15, and 20 wt % PVP, with or without 20 wt % Copaiba oil (Copaifera sp.), were produced by solution blow spinning (SBS), using polymer injection rate of 120 μL min^?1, gas pressure of 2.4 kPa, working distance of 20 cm, and collector rotation of 200 rpm. The morphological, thermal, and spectroscopic properties of these membranes were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermogravimetry (TG), and Fourier transform infrared spectroscopy (FTIR). A method for the evaluation of membrane microbial barrier properties based on resazurin colorimetric method was proposed. Results showed that the addition of both PVP and Copaiba oil produced thicker fibers; otherwise, there was no effect on morphology. Thermal analyses (TG and DSC) indicated the immiscible nature of polymer blends produced, also confirmed by the spectroscopic studies. Antimicrobial barrier properties were related to the antimicrobial effect of Copaiba oil, combined with it hydrophobic nature. The hydrophilic nature of PVP favored degradation of fiber mats, impairing barrier property when higher concentrations of PVP were added. Results indicate that produced spun mats can potentially be used in applications such as wound dressing. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44802.     

Nano and submicrometric fibers of poly(D,L‐lactide) obtained by solution blow spinning: Process and solution variables

Nano and submicrometric fibers of poly(D ,L ‐lactide) (PDLLA or PLA) were spun from solutions using a solution blow spinning (SBS) apparatus. Fiber morphology and diameter were investigated by scanning electron microscopy as a function of polymer concentration, feed rate, and air pressure. A more systematic understanding of the SBS process parameters was obtained, and a quantitative relationship between these parameters and average fiber diameter was established by design of experiments and response surface methodology. It was observed that polymer concentration played an important role in fiber diameter, which ranges from 70 to 2000 nm, and its distribution. Lower polymer concentration tended to increase the formation of bead‐on‐string structures, whereas smooth fibers were formed at higher concentrations. Fiber diameter tended to increase with polymer concentration and decrease with feed rate. Based on these results, optimal conditions could be obtained for solution‐blow spun fibers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Proximate,mineral, amino acid,fatty acid,vitamin E,phytate phosphate and fibre composition of Mimusops zeyheri (Red Milkwood) seed

Mimusops zeyheri, an indigenous tree widely distributed in sub‐Saharan Africa, provides edible fruit. Research on the tree has focused on fruit pulp composition and uses. This study evaluated the nutritional potential of M. zeyheri seed by determining the proximate, fibre and phytate‐phosphate content, the amino acid and fatty acid profiles and vitamin E content of the seed. Dry matter, organic matter, crude protein, ether extract and ash constituted 91.1%, 88.3%, 9.3%, 25.6% and 2.8% of the seed mass respectively. Glutamic acid (1.29 g per 100 g) was the most abundant amino acid. Lysine and phenylalanine were low. Calcium (587.4 mg per 100 g) was the most concentrated macro‐mineral assayed. Gross energy value was 24.34 MJ kg^?1. Lipid yield was 21.3%. Oleic acid was the most abundant fatty acid. Vitamin E concentration was about 2 μg g^?1. Phytate‐phosphate content was 0.03%. Neutral detergent fibre and acid detergent fibre constituted 33.2% and 15.3% respectively. M. zeyheri seed could be exploited as a dietary energy supplement and an oil source rich in oleic acid.