Effect of microporosity on tensile properties of as-cast AZ91D magnesium alloy

In the present study, the effect of microporosity on the tensile properties of as-cast AZ91D magnesium alloy was investigated through experimental observation and numerical prediction. The test specimens were fabricated by die-casting and gravity-casting. For gravity-casting, the inoculation and use of various metallic moulds were applied to obtain a wide range of microporosity. The deficiency of the interdendritic feeding of the liquid phase acted as a dominant mechanism on the formation of the micropores in the Mg?Al-alloys, rather than the evolution of hydrogen gas. Although tensile strength and elongation has a nonlinear and very intensive dependence upon microporosity, the yield strength appeared to have a linear relationship with microporosity. However, it was possible to quantitatively estimate the linear contribution of microporosity on the individual tensile property for a range of microporosity, which was below about 1%. The numerical prediction suggests that the effect of microporosity on fractured strength and elongation decreased as the strain hardening exponent increased. Furthermore, the shape and distribution of micropores may play a more dominant role than local plastic deformation on the tensile behavior of AZ91D alloy.     

On the uniqueness of some helical flows of a second grade fluid

Summary The uniqueness of some helical flows of a second grade fluid, between two infinite circular cylinders, is proved. Initially, the fluid is at rest and flow is produced by the motion of the cylinders. Finally, the special case of a flow in a circular cylinder is considered.     

A probabilistic method for the design of power grounding systems

An improved multivariable, probabilistic method for the safety analysis of power grounding systems is presented. The application of this method is demonstrated in four examples. The first three examples illustrate the practical evaluation of one new and two existing substation grounding grids when the substation is connected to an overhead distribution system. The fourth example ascertains the relative impact of a difference between the S curve of IEC Publication 479 and Dalziel's equation for the allowable body current used in ANSI/IEEE Std 80-1986 on the validity of an exposure model based on the requirements of Std 80. In this example, the statistical data on ground faults have been taken from actual system records. Further possible refinements of the exposure model are discussed     

Trenched‐Sinker LDMOSFET (TS‐LDMOS) Structure for 2 GHz Power Amplifiers

This paper proposes a new LDMOSFET structure with a trenched sinker for high‐power RF amplifiers. Using a low‐temperature, deep‐trench technology, we succeeded in drastically shrinking the sinker area to one‐third the size of the conventional diffusion‐type structure. The RF performance of the proposed device with a channel width of 5 mm showed a small signal gain of 16.5 dB and a maximum peak power of 32 dBm with a power‐added efficiency of 25% at 2 GHz. Furthermore, the trench sinker, which was applied to the guard ring to suppress coupling between inductors, showed an excellent blocking performance below ?40 dB at a frequency of up to 20 GHz. These results confirm that the proposed trenched sinker should be an effective technology both as a compact sinker for RF power devices and as a guard ring against coupling.     

Thermal degradation of cinnamoylated poly(vinyl alcohol)

Thermogravimetry and pyrolysis in combination with gas chromatography and infrared spectroscopy were the experimental techniques applied to the thermal degradation of cinnamoylated poly(vinyl alcohol) samples, constituted from vinyl alcohol-vinyl cinnamate photocrosslinkable copolymers. The thermal decomposition products include gases, liquids and solids. The gases are formed from saturated and unsaturated volatile hydrocarbons C₁? C₄, carbon monoxide and carbon dioxide. The liquid fraction includes aromatic hydrocarbons and some oxygenated organic compounds. The solid product identified in the greatest amount was cinnamic acid. The content in the thermal decomposition products varies considerably both with copolymer composition and temperature.     

The thermal ignition of lignocellulosics in infinite slab and cubic geometries

Wood shaving samples were heated in both cubic baskets and in a previously described system realising the conditions of the ‘infinite slab’ in thermal ignition. Results from the two sets of experiment were found to be totally consistent with each other.     

Synthesis and characterization of poly(N‐vinyl‐2‐pyrrolidone) grafted sodium alginate hydrogel beads for the controlled release of indomethacin

Graft copolymers of sodium alginate (NaAlg) with N‐vinyl‐2‐pyrrolidone were prepared using azobisisobutyronitrile as initiator. The graft copolymers (NaAlg‐g‐PVP) were characterized with Fourier transform infrared spectroscopy, elemental analysis, and differential scanning calorimetry. Polymeric hydrogel beads of NaAlg and NaAlg‐g‐PVP were prepared by crosslinking method using glutaraldehyde (GA) as a crosslinker in the hydrochloric acid catalyst (HCl) and these beads were used to deliver anti‐inflammatory drug, indomethacin (IM). Chemical stability of the IM after encapsulation into beads was confirmed by FTIR. Preparation conditions of the NaAlg‐g‐PVP beads were optimized by considering the percentage entrapment efficiency, particle size, swelling capacity and their release data. In vitro release studies were performed in simulated gastric fluid (pH 1.2) for the initial 2 h, followed by simulated intestinal fluid (pH 7.4) for 4 h. Effects of GA concentration, exposure time to GA, drug/polymer (d/p) ratio, and concentration of HCl on the release of IM were discussed. It was observed that IM release from the beads decreased with increasing GA concentration and exposure time. IM release also decreases with increasing d/p ratio and HCl concentration. The highest IM release was obtained to be 77% for beads crosslinked with 0.027M GA. Swelling experiments were also performed to compute molecular mass between crosslinks of the beads. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Epitaxial growth of GaN on (0001) Al<Subscript>2</Subscript>O<Subscript>3</Subscript> via solution-cast seed layer formation process using Ga(mDTC)<Subscript>3</Subscript>

This paper reports an alternative method for the growth of GaN epitaxial layer on (0001) Al₂O₃ substrate by hot-wall vapor phase epitaxy technique. Tris (N,N-dimethyldithiocarbamato)-gallium (III), Ga(mDTC)₃ was introduced as a precursor material for the seed layer formation in the growth of GaN. Optimal growth conditions with seed layers formed by the Ga(mDTC)₃ concentration of 0.047 mol/L were identified: Growth temperature was found to be 850 °C, and optimal distance between the reactant outlet and substrate was determined to be 12.5 cm. Characterization results showed that this growth method produce high-crystallinity GaN epitaxial layers at a relatively lower growth temperature compared to the existing growth techniques and simplify the growth process.     

Thermal properties and crystalline structure of liquid crystalline poly(ethylene terephthalate‐co‐2(3)‐chloro‐1,4‐phenylene terephthalate)

Thermal properties and crystalline structure of liquid crystalline (LC) poly(ethylene terephthalate‐co‐2(3)‐chloro‐1,4‐phenylene terephthalate) [copoly(ET/CPT)] were investigated using differential scanning calorimetry (DSC), thermogravimetry (TGA), limiting oxygen index (LOI) measurement, electron dispersive X‐ray analysis (EDX), X‐ray diffractometry, and infrared spectrometry (IR). The thermal transition temperatures of copoly(ET/CPT) were changed with the composition. Copoly(ET/CPT) showed two thermal decomposition steps and the residues at 700°C and LOI values of copoly(ET/CPT) were almost proportional to its chlorine content. The activation energy of thermal decomposition of LC units was very low compared to that of poly(ethylene terephthalate)(PET) units. Crystal structure of copoly(ET/CPT) (20/80) was of triclinic system with the lattice constants of a = 9.98 A?, b = 8.78 A?, c = 12.93 A?, α = 97.4°, β = 96.1°, and γ = 90.8°, which is very close to that of poly(chloro‐p‐phenylene terephthlate) (PCPT) with the lattice constants of a = 9.51 A?, b = 8.61 A?, c = 12.73 A?, α = 96.8°, β = 95.4°, and γ = 90.8°. When copoly(ET/CPT)(50/50) was annealed at 220°C in vacuum, crystallization induced sequential reordering (CISR) was not observed but the heat of fusion was slightly increased due to the increase of the trans isomer content in PET units. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1286–1294, 2002; DOI 10.1002/app.10451