Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Design for Consecutive Testability of System-on-a-Chip with Built-In Self Testable Cores

This paper introduces a new concept of testability called consecutive testability and proposes a design-for-testability method for making a given SoC consecutively testable based on integer linear programming problem. For a consecutively testable SoC, testing can be performed as follows. Test patterns of a core are propagated to the core inputs from test pattern sources (implemented either off-chip or on-chip) consecutively at the speed of system clock. Similarly the test responses are propagated to test response sinks (implemented either off-chip or on-chip) from the core outputs consecutively at the speed of system clock. The propagation of test patterns and responses is achieved by using interconnects and consecutive transparency properties of surrounding cores. All interconnects can be tested in a similar fashion. Therefore, it is possible to test not only logic faults but also timing faults that require consecutive application of test patterns at the speed of system clock since the consecutively testable SoC can achieve consecutive application of any test sequence at the speed of system clock.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Optical circulator consisting of a YIG spherical lens, PANDA-fibre polarisers and a fibre-optic polarising beam splitter

A novel optical circulator is reported which employs an yttrium-iron-garnet (YIG) sphere, PANDA-fibre polarisers and a fibre-optic polarising beam splitter. The splitting ratios of the fibre-optic polarising beam splitter were 1.0:99.0 for x-polarisation and 97.5:2.5 for y-polarisation, with an excess loss of 0.5 dB at 1.30 ?m wavelength. The backward isolation of the optical circulator was 30 dB with the total insertion loss of 4.5 dB.     

Crack opening displacement of a through-wall crack in a plate subjected to bending load

This study was performed in order to clarify crack opening displacement (COD) of through-wall cracks in a plate subjected to bending load. The former COD evaluation methods were mainly developed corresponding to tensile load, but there has been nothing that has been developed corresponding to bending load. Therefore, the authors evaluated CODs of the through-wall cracks in plates which were subjected to a bending load using finite element method (FEM) analyses, and proposed a simplified COD evaluation method accounting for both tensile and bending loads. The proposed method is useful for leakage evaluation at a crack opening of an elbow crown or in the vicinity of the coolant surface of a vessel in which the bending stress is relatively large.     

Linearity stablized fiber-optic thermometer using pseudo-heterodyne phase detection

A temperature sensor using a fiber-optic Fabry-Perot interferometer is described. A pseudo-heterodyne detection scheme is adopted to read the light phase difference in the Fabry-Perot interference output. A higher harmonic components comparison method is used to stabilize the system and to increase detection linearity. This system realizes not only highly sensitive temperature sensing with good linearity and minimal adjusting error, but also application to the sensing of other physical quantities such as vibrations. Additionally, the signal-to-noise ratio and distortion of the detected signal are investigated as functions of fiber end reflectivity. These results will be useful in designing a high performance fiber-optic Fabry-Perot thermometer.     

Clinical and serological study of tsutsugamushi disease in northern Osumi, Kagoshima Prefecture

We report 34 cases of tsutsugamushi disease seen from 1989 to 1993 at Yagi Clinic, northern Osumi, Kagoshima Prefecture. Nineteen patients (55.9%) showed the highest antibody titers against the Kawasaki strain Orientia tsutsugamushi (Ot) and 13 (38.2%) against the Kuroki strain Ot. It is suggested that two antigenic types (Kawasaki and Kuroki) of Ot were distributed in Kagoshima Prefecture, and the Kawasaki type Ot more or less dominates Kuroki type Ot. There was no difference in clinical features between the two groups of patients.     

Right atrial contractile performance in patients with myocardial infarction

To evaluate right atrial (RA) contractile performance in patients with myocardial infarction, we validated a cineangiographic method of RA volume measurement, and investigated RA volume change in 'normal' individuals and patients with a previous myocardial infarction. Sixteen silicone rubber RA casts made from human cadavers were filmed in the postero-anterior and left lateral projections. The cast volumes calculated following Simpson's rule were in good agreement with those measured by water replacement (r = 0.992, P < 0.01). At cardiac catheterization, biplane RA cineangiography was performed in 19 'normal' individuals (N group), in 14 patients with a previous antero-septal infarction (AMI group) and in seven patients with a previous inferior infarction (IMI group). The RA volume-time curve was constructed at 20-40 ms intervals for one cardiac cycle. RA volume at the beginning of the atrial contraction (RAVd), which was defined as the 'preload' of the RA, tended to be larger in both the AMI and IMI groups compared with 'normal' individuals. The RA ejection volume was significantly larger in both the AMI (18.4 +/- 2.1 ml.m-2, P < 0.01) and IMI groups (19.4 +/- 2.8, P < 0.01) than in the N group (14.5 +/- 1.9), even for a comparable level of RAVd (range from 26 to 36 ml.m-2) (18.6 +/- 2.1, P < 0.01, 18.2 +/- 2.0, P < 0.01, 14.7 +/- 1.9, respectively). These results suggest that RA contraction increases in patients with myocardial infarction by increasing both the 'preload' and 'contractility' of the RA.     

A 0.1-μm delta-doped MOSFET fabricated with post-low-energyimplanting selective epitaxy

A simple fabrication technology for delta-doped MOSFETs, named post-low-energy implanting selective epitaxy (PLISE) is presented. The PLISE technology needs no additional photo-lithography mask, deposition step or etching step even for CMOS devices. The only additional step is growing undoped epitaxial channel layers by UHV-CVD after the channel implantation. With this technology, delta-doped NMOSFETs with 0.1-μm gate length were successfully fabricated. By optimizing the epi-layer thickness and the channel doping level, short-channel effects are suppressed enough to achieve 0.1-μm gate length. Moreover, the junction capacitance at zero bias is reduced by 50%