Oxidation behavior of single-crystal Al2O3-fiber-reinforced Ni3Al-based composites

A series of single-crystal Al₂O₃-fiber-reinforced Ni3Al-based intermetallic matrix composites were fabricated by pressure casting. The matrices employed were binary Ni₃Al, Ni₃Al-0.5 at. pct Cr, and Ni₃Al-0.34 at. pct Zr. The development of microstructure upon oxidation in air at either 1100 °C or 1200 °C was investigated by optical, scanning, and transmission electron microscopy. In air-oxidized binary Ni₃Al, some of the fibers were fully or partially covered with a layer of oxide. A weak fiber/matrix bond in this system, which led to fiber debonding during composite processing, is believed to be responsible for the ingress of O into the composite and oxidation of the matrix in the debonded regions at the fiber/matrix interface. Addition of Cr to Ni₃Al resulted in an almost threefold increase in fiber/matrix bond strength. No oxidation of the interface was observed. A thick layer of oxide was formed around all the fibers when the composite was thermally cycled prior to isothermal annealing. Addition of Zr to Ni₃Al resulted in the formation of a layer of ZrO₂ on the surface of the fibers during composite processing. The ZrO₂ layer provided a fast path for the diffusion of O, which led to the formation of a rootlike oxide structure around the fibers. The rootlike structure consisted of a network of Al₂O₃-covered ZrO₂.     

Analysis of variance based on fuzzy observations

Analysis of variance (ANOVA) is an important method in exploratory and confirmatory data analysis. The simplest type of ANOVA is one-way ANOVA for comparison among means of several populations. In this article, we extend one-way ANOVA to a case where observed data are fuzzy observations rather than real numbers. Two real-data examples are given to show the performance of this method.     

Polypropylene cellulose‐based composites: The effect of bagasse reinforcement and polybutadiene isocyanate treatment on the mechanical properties

Using bagasse fiber as the reinforcing filler and polypropylene as the thermoplastic matrix polymer, a reinforced composite was prepared, and its mechanical properties examined as a function of the amount of compatibilizing agents used. In the sample preparation, four levels of fiber loading (10, 20, 30, and 40 wt %), three levels of polybutadiene isocyanate (PBNCO) content (0, 2, and 4 wt %) and two levels of maleated polypropylenes (MAPP) content (0 and 3 wt %) as compatibilizing agents were used. The tensile properties of the composites improved as the fiber loading and the compatibilizing agents increased, but the impact strength was significantly decreased. The mechanical study revealed that the positive effect of compatibilizing agents on interfacial bonding. The composites treated with PBNCO showed superior tensile and impact properties than those without treatment. The findings indicated that bagasse as agro‐waste material is a valuable renewable natural resource for composite production and could be utilized as a substitute for wood in composite industries. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The Electronic and Magnetic Properties and the Topological Phase Graphene Sheet with Fe,Co, Si,and Ge Impurities

The structural, electronic, and magnetic properties of pure graphene sheet and graphene sheet with Fe, Co, Si, and Ge impurities are investigated. The calculated results are done within density functional theory in the presence of spin-orbit coupling using the generalized gradient approximation. Electron density of states, band order, electron charge distribution, magnetic moment of these sheets, and the effect of pressure on the band order of graphene sheet with Fe impurity are investigated.     

Pressure casting of a zirconia-toughened alumina fiber-reinforced NiAl composite

A pressure-cast NiAl composite reinforced with polycrystalline alumina (PRD-166) fibers containing 0.2 weight fraction of partially stabilized zirconia was examined by optical and transmission electron microscopy (TEM). Fibers in the preform used for casting were forced into contact, and fiber bonding occurred in a number of instances. Fiber volume fraction was increased from an initial value of 0.4 to 0.6 as a consequence of the applied pressure. An explanation is offered for the interaction of applied pressure, wetting angle, and the rigidity of the fiber preform on the final volume fraction of the fibers in the composite. At the fiber/matrix interface, the alumina was free of zirconia particles. It is proposed that alumina grain growth forced the zirconia into the molten NiAl, where it dissolved. As solidification took place, the concentration of zirconium in the molten NiAl increased to a point where zirconium reacted with alumina to form zirconia again.     

Effect of corona discharge treatment on indigo dyed cotton fabric

The present study proposes new conditions for achieving the aged-look effect of denim. Indigo dyed cotton fabrics were treated by corona discharge at different power levels and number of passages. Colorimetric parameters of corona treatment were assessed by the CIE L*a*b* colorimetric system and the pH and colour fastness of samples were tested. The surfaces of dyed samples were studied by scanning electron microscopy and Fourier Transform–infrared/attenuated total reflectance (FTIR/ATR) analysis. Under the same conditions of corona treatment, the faded-look effect was reduced as the depth of dyeing was increased. Increasing the power and the number of passages increases L* and b * and decreases a * values. This indicates that samples become lighter and yellower but soaping can reduce yellowness. FTIR/ATR results show that indigo dye oxidises, and isatin and anthranilic acid are produced. The pH levels of corona-treated samples reduce as the power and number of passages increase. This acidification is in agreement with the results of FTIR/ATR analysis.     

Performance properties of microcrystalline cellulose as a reinforcing agent in wood plastic composites

Polypropylene (PP)/microcrystalline cellulose (MCC)/wood flour composites were prepared containing polypropylene-graft-maleic anhydride (PP-g-MA) as compatibilizer. The mechanical, morphological and thermal properties were investigated. The weight ratio of the cellulosic materials to polymer matrix was 40:60 (w:w). The obtained results showed that tensile, flexural and impact strengths of the composites were significantly enhanced with addition of MCC, as compared with pure PP and composites without MCC. The effect of MCC on impact was minimal compared to the effects of PP-g-MA content. Scanning electron microscopy has shown that the composite, with compatibilizer, promotes better fiber–matrix interaction. In all cases, the degradation temperatures shifted to higher values after addition of PP-g-MA. The maximum improvement on the thermal stability of the composites was achieved when 5% PP-g-MA was used. However, the increase in MCC content substantially reduced the thermal stability. This work showed that MCC along with wood flour could be effectively used as reinforcing agent in thermoplastic matrix.     

Insect Telepresence: Using Robotic Tele-Embodiment to Bring Insects Face-to-Face with Humans

The Insect Telepresence project combines expertise from the robotics and human-computer interaction communities to create a robot exhibit that enables telepresence in scale. The underlying mission of this work is educational: to promote appreciation for insect life and small-scale complexity through exploration of live insect colonies. In this article we describe the robot hardware and software used to bring students face-to-face with insects. We also summarize the user-centered design process and formal HCI methods used to design and evaluate the Insect Telepresence robot. The complete working exhibit, now installed as a permanent robot-entomology station at the Carnegie Museum of Natural History, is presented in this paper in words and pictures.