Towards a Better Prediction of Cell Settling on Nanostructure Arrays—Simple Means to Complicated Ends

Vertical arrays of nanostructures (NSs) are emerging as promising platforms for probing and manipulating live mammalian cells. The broad range of applications requires different types of interfaces, but cell settling on NS arrays is not yet fully controlled and understood. Cells are both seen to deform completely into NS arrays and to stay suspended like tiny fakirs, which have hitherto been explained with differences in NS spacing or density. Here, a better understanding of this phenomenon is provided by using a model that takes into account the extreme membrane deformation needed for a cell to settle into a NS array. It is shown that, in addition to the NS density, cell settling depends strongly on the dimensions of the single NS, and that the settling can be predicted for a given NS array geometry. The predictive power of the model is confirmed by experiments and good agreement with cases from the literature. Furthermore, the influence of cell‐related parameters is evaluated theoretically and a generic method of tuning cell settling through surface coating is demonstrated experimentally. These findings allow a more rational design of NS arrays for the numerous exciting biological applications where the mode of cell settling is crucial.     

Electrospun microporous gelatin–polycaprolactone blend tubular scaffold as a potential vascular biomaterial

The work reported involved the fabrication of an electrospun tubular conduit of a gelatin and polycaprolactone (PCL) blend as an adventitia‐equivalent construct. Gelatin was included as the matrix for increased biocompatibility with the addition of PCL for durability. This is contrary to most of the literature available for biomaterials based on blends of gelatin and PCL where PCL is the major matrix. The work includes the assiduous selection of key electrospinning parameters to obtain smooth bead‐free fibres with a narrow distribution of pore size and fibre diameter. Few reports elucidate the optimization of all electrospinning parameters to fabricate tubular conduits with a focus on obtaining homogeneous pores and fibres. This stepwise investigation would be unique for the fabrication of gelatin–PCL electrospun tubular constructs. The fabricated microfibrous gelatin–PCL constructs had pores of size ca 50–100 μm reportedly conducive for cell infiltration. The measured value of surface roughness of 57.99 ± 17.4 nm is reported to be favourable for protein adhesion and cell adhesion. The elastic modulus was observed to be similar to that of the tunica adventitia of the native artery. Preliminary in vitro and in vivo biocompatibility tests suggest safe applicability as a biomaterial. Minimal cytotoxicity was observed using MTT assay. Subcutaneous implantation of the scaffold demonstrated acute inflammation which decreased by day 15. The findings of this study could enable the fabrication of smooth bead‐free microfibrous gelatin–PCL tubular construct as viable biomaterial which can be included in a bilayer or a trilayer scaffold for vascular tissue engineering. © 2019 Society of Chemical Industry     

5-Benzylidene-4-Oxazolidinones Are Synergistic with Antibiotics for the Treatment of Staphylococcus aureus Biofilms

The failure of frontline antibiotics in the clinic is one of the most serious threats to human health and requires a multitude of novel therapeutics and innovative approaches to treatment so as to curtail the growing crisis. In addition to traditional resistance mechanisms resulting in the lack of efficacy of many antibiotics, most chronic and recurring infections are further made tolerant to antibiotic action by the presence of biofilms. Herein, we report an expanded set of 5-benzylidene-4-oxazolidinones that are able to inhibit the formation of Staphylococcus aureus biofilms, disperse preformed biofilms, and, in combination with common antibiotics, are able to significantly reduce the bacterial load in a robust collagen-matrix model of biofilm infection.     

High‐intensity sweeteners in espresso coffee: ideal and equivalent sweetness and time–intensity analysis

The efficient substitution of sucrose by a sweetener in beverages requires the application of some sensory techniques. First, one must determine the concentrations of the sweeteners under study, equivalent in sweetness to the ideal sucrose concentration. In addition, it is fundamental to determine which is most similar to sucrose. The objectives of this study were to determine the ideal sweetness for espresso coffee and the equivalent concentrations in sweetness of different sweeteners, as well as characterise the time–intensity profile of each sweetener in relation to sweetness. The sweeteners evaluated were sucralose, aspartame, neotame, a cyclamate/saccharin mixture (2:1) and stevia. The sucrose concentration considered ideal by consumers was 12.5% (w/v), and the equivalent concentrations of the sweeteners were 0.0159% for sucralose, 0.0549% for aspartame, 0.0016% for neotame, 0.0359% for the cyclamate/saccharin mixture and 0.0998% for stevia. The time–intensity analysis indicated that possibly the sweeteners neotame, aspartame and sucralose would be the best substitutes for sucrose.     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

Silicon-to-steel bonding using rapid thermal annealing

This paper presents the rapid, low-temperature bonding between silicon and steel using the rapid thermal annealing process. Three different thin-film adhesion layer systems including silver, gold, and nickel were utilized as the intermediate bonding material to assist the eutectic Pb/Sn bonding between silicon and steel. The bonding temperature was set at 220/spl deg/C for 20 s, with a 20-s ramp-up time. Five experiments were conducted to determine the strength of the bond, including static tensile and compressive four-point bend tests, axial extension tests, tensile bending fatigue tests, and corrosion resistance tests. The test results have shown that the gold adhesion layer is the most robust, demonstrating minimal creep during fatigue tests, no delamination during the tensile or compressive four-point bend tests, and acceptable strength during the axial extension tests. Additionally, all adhesion layers have withstood four months of submersion in various high-temperature solutions and lubricants without failure. Simulations of the axial stresses and strains that developed during the four-point bend and axial extension tests were performed and showed that the presence of the silicon die provides a local reinforcement of the bond as observed in the experimental tests.     

The relationship between bioelectrical impedance phase angle and subjective global assessment in advanced colorectal cancer

Background  

Bioelectrical Impedance (BIA) derived phase angle is increasingly being used as an objective indicator of nutritional status in advanced cancer. Subjective Global Assessment (SGA) is a subjective method of nutritional status. The objective of this study was to investigate the association between BIA derived phase angle and SGA in advanced colorectal cancer.