Physicochemical and technological properties of beef burger as influenced by the addition of pea fibre

This study aimed to evaluate the physicochemical characteristics and sensory attributes of beef burgers with the addition of pea fibre as a partial substitute of meat or fat. Three formulations were prepared: control (CON) – similar to the commercial formulation; fibre/less meat (FLM)—5% meat reduction and addition of 1% pea fibre; fibre/less fat (FLF)—7% fat reduction and addition of 1% pea fibre. Non-significant differences were obtained for pH, colour parameters (L* and b*), texture profile, cooking loss and size reduction among formulations. Moreover, sensory analysis with consumers of beef burgers did not indicate differences among the formulations for all the analysed attributes. Therefore, pea fibre is a promising partial replacer for meat and fat in beef burgers due to the preservation of technological parameters and sensory acceptance.     

Technological and sensorial properties of liquid nitrogen ice cream enriched with protein from brewing waste (trub)

Debittered trub (brewing waste) is an important source of protein source (70.26%). Trub and whey protein were used for 5% protein enrichment of ice cream frozen by liquid nitrogen. Three formulations were elaborated: ice cream standard (ICS), ice cream with whey protein (ICW) and ice cream with trub (ICT). Chemical composition, rheological properties, texture, overrun, melting rate, scanning electron microscopy and a sensorial test were performed. Results showed that ICT presented a higher viscosity, obtained on the upward curve up to 6.76 Pa s⁻¹, consistency index (22.96 (Pa s⁻¹)ⁿ), hysteresis area (140.40 mPa s⁻¹) and hardness (31113.33 g) but a lower melting rate (0.38 g min⁻¹), overrun (13.92%) and sensorial acceptability than the other formulations. The addition of trub debittered for protein enrichment improved ice cream properties and demonstrated that it could be used as a food ingredient.     

Biodegradability Study of the Biosurfactant Contained in a Crude Extract from Corn Steep Water

Over the last few years, the global biosurfactant market has raised due to the increasing awareness among consumers, for the use of biological or bio-based products. Because of their composition, it can be speculated that these are more biocompatible and more biodegradable than their chemical homologous. However, at the moment, no studies exist in the literature about the biodegradability of biosurfactants. In this work, a biosurfactant contained in a crude extract, obtained from a corn wet-milling industry stream that ferments spontaneously in the presence of lactic acid bacteria, was subjected to a biodegradation study, without addition of external microbial biomass, under different conditions of temperature (5–45 °C), biodegradation time (15–55 days), and pH (5–7). For that, a Box–Behnken factorial design was applied, which allowed to predict the percentage of biodegradation for the biosurfactant contained in the crude extract, between the range of the independent variables selected in the study, obtaining biodegradation values between 3 and 80%. The percentage of biodegradation for the biosurfactant was calculated based on the increase in the surface tension of samples of the crude extract. Furthermore, it was also possible to predict the variation in t_1/2 for the biosurfactant (time to achieve the 50% of biodegradation) under different conditions.     

Real-time organic aerosol chemical speciation in the indoor environment using extractive electrospray ionization mass spectrometry

Understanding the sources and composition of organic aerosol (OA) in indoor environments requires rapid measurements, since many emissions and processes have short timescales. However, real-time molecular-level OA measurements have not been reported indoors. Here, we present quantitative measurements, at a time resolution of five seconds, of molecular ions corresponding to diverse aerosol-phase species, by applying extractive electrospray ionization mass spectrometry (EESI-MS) to indoor air analysis for the first time, as part of the highly instrumented HOMEChem field study. We demonstrate how the complex spectra of EESI-MS are screened in order to extract chemical information and investigate the possibility of interference from gas-phase semivolatile species. During experiments that simulated the Thanksgiving US holiday meal preparation, EESI-MS quantified multiple species, including fatty acids, carbohydrates, siloxanes, and phthalates. Intercomparisons with Aerosol Mass Spectrometer (AMS) and Scanning Mobility Particle Sizer suggest that EESI-MS quantified a large fraction of OA. Comparisons with FIGAERO-CIMS shows similar signal levels and good correlation, with a range of 100 for the relative sensitivities. Comparisons with SV-TAG for phthalates and with SV-TAG and AMS for total siloxanes also show strong correlation. EESI-MS observations can be used with gas-phase measurements to identify co-emitted gas- and aerosol-phase species, and this is demonstrated using complementary gas-phase PTR-MS observations.     

Preparation and characterization of chitosan‐based dispersions

Complexation of chitosan in aqueous solutions by low molecular weight electrolytes is one of the simplest methods for the preparation of aqueous chitosan dispersions. In this work, the influence of storage time, sulfate concentration, method of preparation and surfactant content on some properties of the resultant chitosan dispersions (turbidity, viscosity and zeta potential) was analyzed. Turbidimetry was adequate to monitor the formation of particles, while viscometry was suitable to monitor changes in the dispersing phase. An analysis of the properties of these systems, mainly in terms of particle–particle and macromolecule–macromolecule interactions was carried out. Copyright © 2004 Society of Chemical Industry     

Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry