Matrix Transformation in Boron Containing High-Temperature Co–Re–Cr Alloys

An addition of boron largely increases the ductility in polycrystalline high-temperature Co–Re alloys. Therefore, the effect of boron on the alloy structural characteristics is of high importance for the stability of the matrix at operational temperatures. Volume fractions of ε (hexagonal close-packed—hcp), γ (face-centered cubic—fcc) and σ (Cr₂Re₃ type) phases were measured at ambient and high temperatures (up to 1500 °C) for a boron-containing Co–17Re–23Cr alloy using neutron diffraction. The matrix phase undergoes an allotropic transformation from ε to γ structure at high temperatures, similar to pure cobalt and to the previously investigated, more complex Co–17Re–23Cr–1.2Ta–2.6C alloy. It was determined in this study that the transformation temperature depends on the boron content (0–1000 wt. ppm). Nevertheless, the transformation temperature did not change monotonically with the increase in the boron content but reached a minimum at approximately 200 ppm of boron. A probable reason is the interplay between the amount of boron in the matrix and the amount of σ phase, which binds hcp-stabilizing elements (Cr and Re). Moreover, borides were identified in alloys with high boron content.     

On the cover.

Discusses the cover art for this issue of American Psychologist. Portions of the article are based on an interview with the artist, Melissa Miller, on November 6, 2006. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Structural Response of Nuclear Containment Shield Buildings with Construction Openings

Steam generator replacement at nuclear power plants requires large construction openings in nuclear containment structures. This study examines the effects of such openings placed in a 61?cm (2?ft) thick dome of a shield building. The dome is cast in two layers, and the limiting cases of the two layers acting as one and the lower layer carrying the entire load are considered. Without openings, the stresses due to dead load in the structure are very low when compared to the material strength. With openings, the loads are easily redistributed around the opening, and the maximum stresses for the conservative case are between three and four and one-half times larger than in the original structure with no openings. The extent of the affected area around the holes is relatively small. Smooth corners in the openings are necessary to avoid high local stress concentrations.     

Convolutional solutions of partial difference equations

A significant part of the theory of one-dimensional linear shift-invariant systems is based on the concept of weighting function (or impulse response): the output is the convolution of the weighting function with the input. This paper introduces the concept of linear translation-invariant systems and uses this notion in studying impulse response, z-transforms, and transfer functions for multidimensional systems.     

Viscous and Aeroelastic Effects on Wind Turbine Blades. The VISCEL project. Part I: 3D Navier–Stokes Rotor simulations

Aerodynamic modelling of HAWT rotors by means of “engineering methods” has reached a saddle point, where no further development can be expected without a breakthrough in understanding the physics of unsteady, rotating three‐dimensional flows. However, such a breakthrough becomes ever more necessary, as the size of the wind turbines increases. With the experimental work in that direction being mostly limited to observing the phenomena and interpreting the associated mechanisms, and its increased cost, alternatives are being sought. The use of CFD techniques and state‐of‐the‐art Navier–Stokes solvers is considered a very serious contender, a belief shared by the members of the present consortium, which has worked on the VISCEL JOR3‐CT98‐0208 Joule III project. This project's goal was to determine the aerodynamic characteristics as well as the aeroelastic behaviour of wind turbine blades across their broad range of operational conditions, from attached to highly separated flow regimes. The work programme included specific tasks for the validation and assessment of existing 3D solvers, for the parametric study of 3D flow around realistic blades and for the investigation of aeroelastic stability, at the blade section level. Copyright © 2003 John Wiley & Sons, Ltd.     

A quantitative approach to modeling mammalian myelinated nervefibers for electrical prosthesis design

Presents an upgraded cable model of mammalian myelinated nerve fibers in an extracellularly applied field. The kinetics of the nodes is based upon voltage clamp data in rat motor fibers at 37°C (J.R. Schwartz and G. Eikhof, 1987), while the resting membrane potential is computed with the Goldman equation. The resulting spike shape, conduction velocity, strength/duration behavior, and absolute and relative refractory period are in good quantitative agreement with published experimental data in mammals at normal body temperature and at 20°C. Results at intermediate temperatures however, suggest that the widely used concept of a constant Q₁₀ for the rate constants is invalid. In addition, the model generates realistic abortive spikes towards the end of the absolute refractory period and it can describe the consequences of repetitive firing. The results stress the advantages of a multiple nonlinear node model even if only time aspects of nerve behavior are under study. It turned out, that the model presented here describes in vivo neural properties relevant for electrical prosthesis design better than previous models in literature