Field-induced spin density waves in Bechgaard salts in the presence of normal impurities

We study theoretically the effect of the quasiparticle scattering in field-induced spin density waves (FISDW) in Bechgaard salts in a high magnetic field. The effects of scattering are introduced by a random impurity model similar to the one used by Zittartz in his analysis of the charge density wave. Within the single-gap approximation and weak impurity scattering, we find that the FISDW with normal impurities is similar to a superconductor with magnetic impurities. From this analogy the thermodynamics as well as the electronic thermal conductivity and the sound attenuation coefficient of the FISDW are obtained.On leave of absence from Nankai University, China.     

Crystallization process and magnetic properties of Fe100−x,B x (10 ≦ × ≦ 35) amorphous alloys and supersaturated state of boron inα-Fe

Amorphous specimens of Fe_100–x B _x were prepared in the range 10 × 35 at % B by a single-roller method. The crystallization process and the boron concentration dependence of the Curie temperature were examined by differential scanning calorimetry, X-ray diffraction, Mössbauer spectroscopy and magnetic measurements. Two-step crystallization was observed in specimens with× < 17: amorphous amorphous + boron-supersaturated b c c phase (-Fe(B)) t-Fe₃B +-Fe. A single-Fe(B) phase was not observed. The transition temperature from t-Fe₃B to stable (-Fe + t-Fe₂B) sensitively depends on the boron content in the alloys. The crystallization temperature (T _x) of the amorphous alloys was almost unchanged for 17 × 31, but increased remarkably at high boron concentrations of× 33, where the decomposition products consisted of t-Fe₂B and o-FeB. The Curie temperature (T _c) of the amorphous phase was as low as 480 K at× = 10, increased with increasing boron content up to 820 K and then decreased in the high boron concentration alloys of× > 28. A single-Fe(B) phase was not detected in the as-quenched specimens of× = 8 and 10. The phase coexisted with the o-Fe₃B and amorphous phases. The lattice parameter of the phase was 0.2861₀ nm which was smaller than that of pure iron by 2/1000, indicating the substitutional occupation of boron atoms in the b c c lattice.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

In Situ Synthesis and Microstructures of Tungsten Carbide-Nanoparticle-Reinforced Silicon Nitride-Matrix Composites

A W₂C-nanoparticle-reinforced Si₃N₄-matrix composite was fabricated by sintering porous Si₃N₄ that had been infiltrated with a tungsten solution. During the sintering procedure, nanometer-sized W₂C particles grew in situ from the reaction between the tungsten and carbon sources considered to originate mainly from residual binder. The W₂C particles resided in the grain-boundary junctions of the Si₃N₄, had an average diameter of ∼60 nm, and were polyhedral in shape. Because the residual carbon, which normally would obstruct sintering, reacted with the tungsten to form W₂C particles in the composite, the sinterability of the Si₃N₄ was improved, and a W₂C–Si₃N₄ composite with almost full density was obtained. The flexural strength of the W₂C–Si₃N₄ composite was 1212 MPa, ∼34% higher than that of standard sintered Si₃N₄.     

Tribological Characteristics of SiC Ceramics in High-Temperature and High-Pressure Water

The effects of temperature and sliding speed on the tribological behavior of a SiC ceramic by sliding on the same material in deoxygenated water were investigated from room temperature to 300°C under the corresponding saturated vapor pressures. The friction coefficient and specific wear rates of both plates and disks increased at elevated temperatures at all sliding speeds, but decreased with increasing sliding speed at 120° and 300°C. Fine mirrorlike worn surfaces were observed without wear debris under all sliding conditions. The wear mechanism appears to consist of hydrothermal oxidation of SiC and dissolution of reaction products such as silica.     

Mechanochemically synthesized ZIF-8 nanoparticles blended into 6FDA-TrMPD membranes for C3H6/C3H8 separation

The mixed matrix membranes (MMMs) consisting zeolitic-imidazolate framework-8 (ZIF-8) nanoparticles in a polymer have been of considerable interest in separation applications. The fillers used are mostly synthesized using the solvothermal method. In this study, the ZIF-8 nanoparticles were synthesized using a solvent-less and salt-free mechanochemical method and were added to 6FDA-TrMPD polyimide to prepare MMMs. The single gas permeation of C₃H₆ and C₃H₈ through the MMMs was investigated. The C₃H₆ permeability and C₃H₆/C₃H₈ ideal selectivity of a 20 wt% mechano-synthesized ZIF-8/6FDA-TrMPD MMM were 70% and 32% higher than those of the neat polymer membrane at 0.1 MPa and 308 K, respectively. The C₃H₆/C₃H₈ separation performance of the mechano-synthesized ZIF-8 MMM was similar to that of the conventional solvothermal-synthesized ZIF-8 MMM. This separation performance was in good agreement with the Maxwell model. Temperature and pressure dependence analyses confirmed that the mechano-synthesized ZIF-8 nanoparticles acted as molecular sieves in the MMMs for the C₃H₆ and C₃H₈ permeation.     

Optimum combination of operating parameters in abrasive cut-off

For optimization of abrasive cut-off operation, wheel wear equation must be identified before the operation is optimized. The equation is obtained by using GMDH algorithm with successive determination of trends containing interactive terms. In the model equation factors of grinding fluid are taken into consideration in addition to the factors of wheel, work material, feed (table speed) and wheel speed. For the identification of the model wheel wear tests are performed under the experimental design treating the above-mentioned factors as independent variables. The grinding ratio (output in the model) can be predicted for combinations of various factors using the model. With the wheel wear equation and machining cost model, the optimum combination of wheel, fluid, feed and wheel speed can be selected for a given work material. The relationships between these variables and the costs are investigated.