A new write/erase method to improve the read disturbcharacteristics based on the decay phenomena of stress leakage currentfor flash memories

This paper describes a new write/erase method for flash memory to improve the read disturb characteristics by means of drastically reducing the stress leakage current in the tunnel oxide. This new write/erase operation method is based on the newly discovered three decay characteristics of the stress leakage current. The features of the proposed write/erase method are as follows: 1) the polarity of the additional pulse after applying write/erase pulse is the same as that of the control gate voltage in the read operation; 2) the voltage of the additional pulse is higher than that of a control gate in a read operation, and lower than that of a control gate in a write operation; and 3) an additional pulse is applied to the control gate just after a completion of the write/erase operation. With the proposed write/erase method, the degradation of the read disturb life time after 10⁶ write/erase cycles can be drastically reduced by 50% in comparison with the conventional bipolarity write/erase method used for NAND type flash memory. Furthermore, the degradation can he drastically reduced by 90% in comparison with the conventional unipolarity write/erase method fur NOR-, AND-, and DINOR-type flash memory. This proposed write/erase operation method has superior potential for applications to 256 Mb flash memories and beyond     

Fracture toughness measurement with fatigue-precracked single edge-notched beam specimens of WC-Co hard metal

The plain-strain fracture toughness of WC-8%Co hard metal, K _IC, was measured using single edge-notched beam (SENB) specimens with fatigue precrack. The fatigue precrack was introduced with compressive fatigue cycling in four-point bending at room temperature. Since stable fatigue-crack propagation was obtained from the notch tip, it was easy to control the fatigue-precrack length. A reasonable K _IC value of 13.3 MPa m^1/2 was obtained with the fatigue-precracked SENB specimens in four-point bending. The compressive fatigue-precracking technique in four-point bending was simple and convenient, and is therefore applicable to precracking in a variety of brittle materials prior to fracture-toughness measurements.     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.     

Handling of fine-particles by time-averaged particle driving method in plasmas

We developed a noble technique for the fine-particle handling in plasmas. In this method a pair of point electrodes are introduced in the plasma, to which positive pulses are applied alternatively. When the pulse repetition period is shorter than the particle response time, the particles feel only time-averaged force because of their large mass. Spatial profile of the equivalent potential of the time-averaged force varies from a circle to an ellipse with an increase in the local discharge at the electrodes. The particles are eventually transported toward a middle point between two point-electrodes, being almost independent of their initial positions. This method is quite effective for converging fine particles in the plasma.     

Adsorption of urea,creatinine, and uric acid from three solution types using spherical activated carbon and its recyclability

In this paper, we propose that the urinary toxins from the wastewater be adsorbed on an adsorbent such as spherical activated carbon and the latter be regenerated by subjecting it to high temperatures to recycle activated carbon and also to recycle the water used in dialysis. We studied the adsorption of artificial waste dialysate, which is a mixed solution of urea, creatinine, and uric acid, and the separate solutions for each of these and found that their extents of adsorption onto the spherical activated carbon material were nearly identical. The amount of adsorption was approximately 1.4 mg·g^-1 for urea, 18 mg·g^-1 for creatinine, and 20 mg·g^-1 for uric acid. The urea, creatinine, and uric acid adsorbed onto the spherical activated carbon decomposed on heat treatment at 500℃, and the adsorption capacity of the spherical activated carbon was regenerated. Our study successfully demonstrated that the spherical activated carbon can be recycled in the waste dialysate treatment process.     

In Situ Synthesis and Microstructures of Tungsten Carbide-Nanoparticle-Reinforced Silicon Nitride-Matrix Composites

A W₂C-nanoparticle-reinforced Si₃N₄-matrix composite was fabricated by sintering porous Si₃N₄ that had been infiltrated with a tungsten solution. During the sintering procedure, nanometer-sized W₂C particles grew in situ from the reaction between the tungsten and carbon sources considered to originate mainly from residual binder. The W₂C particles resided in the grain-boundary junctions of the Si₃N₄, had an average diameter of ∼60 nm, and were polyhedral in shape. Because the residual carbon, which normally would obstruct sintering, reacted with the tungsten to form W₂C particles in the composite, the sinterability of the Si₃N₄ was improved, and a W₂C–Si₃N₄ composite with almost full density was obtained. The flexural strength of the W₂C–Si₃N₄ composite was 1212 MPa, ∼34% higher than that of standard sintered Si₃N₄.     

Effect of platelet-activating factor on lipoprotein lipase and blood lipids

We investigated the effect of platelet-activating factor (PAF) and of the PAF specific antagonist CV-6209 on plasma lipid metabolism, and particularly on post-heparin plasma lipolytic activity in male Wistar rats. Lipoprotein lipase (LPL) activity was enhanced by intravenous injection of PAF before intravenous injection of heparin when the PAF dose was low (0.2 μg/kg). PAF activated hepatic triacylglycerol lipase (HTGL) activity dose-dependently. Plasma triacylglycerols (TG) significantly decreased with the activation of LPL and/or HTGL. Plasma total cholesterol (TC) and phospholipid (PL) levels decreased at a low dose of PAF (0.2 μg/kg), but increased when higher doses were used. The PAF antagonist CV-6209 partially reversed the PAF induced effects on HTGL, TC and PL. Based on a paper presented at the Third International Conference on Platelet-Activating Factor and Structurally Related Alkyl Ether Lipids, Tokyo, Japan, May 1989.     

Influence of ammonium salt on electrowinning of copper from ammoniacal alkaline solutions

In order to develop an energy-saving copper recycling process from wastes, electrochemical measurements were conducted in ammoniacal alkaline solutions containing Cu(I) ions and an ammonium salt of sulfate, chloride or nitrate. The results of each system were then compared. The polarization measurements suggested that the voltage required for the electrode process is lower in the chloride and nitrate systems than that in the sulfate system. The cathode current efficiency during the copper electrodeposition varied from 39 to 97% and increased with current density in the chloride and sulfate systems. In the nitrate system, the lowest cathode current efficiency of 30% was observed because of nitrate ion reduction. Based on these results, the power consumption required for the electrowinning stage of the copper recycling process was calculated. Among these three systems, the chloride system showed the lowest power consumption of 500 kWh t⁻¹ at the current density of 200 A m⁻², which is about 25% of the conventional copper electrowinning process from a copper sulfate-sulfuric acid solution.     

Conformational studies of poly(N-methyl-l-alanine) by n.m.r. spectroscopy

Nuclear magnetic resonance (n.m.r.) and circular dichroism of $\text{poly}\text{(N-}\text{methyl-}\text{l}\text{-alanine}\text{)}$ in methylene $\text{chloride}\text{-d}{}_2\text{dichloroacetic acid}$ were investigated. In methylene chloride-d₂$\text{poly}\text{(N-}\text{methyl-}\text{l}\text{-alanine}\text{)}$ was found to consist of nearly all-trans amide bonds and assume a stable secondary structure. Trace amounts of cis amide bonds were also present. The addition of dichloroacetic acid destroyed the secondary structure and induced a drastic change of the n.m.r. spectrum, which was similar to that observed with the monomeric amide, $\text{N-}\text{acetyl}\text{-N-}\text{methyl-}\text{l}\text{-alanine}$ dimethylamide. In comparison of the polymer with the monomeric amide, it was concluded that the transition of $\text{poly}\text{(N-}\text{methyl-}\text{l}\text{-alanine}\text{)}$ was caused by the isomerization of amide bonds. The complex n.m.r. spectrum was interpreted in terms of the distribution along the polymer chain of various non-planar amide links as well as planar cis and trans amide links. The difference of the mechanism of conformational transition between poly(amino acid) and poly(imino acid) is also discussed.     

Swarm robotic network using Lévy flight in target detection problem

One approach in swarm robotics is homogeneous system which is embedded with sensing, computing, mobile and communication components. In this study, a target detection problem, which is one of navigation problems, was employed. Once a robot detects a target, robots immediately communicate with a base station via intermediate relay robots due to the multi-hop transmission of wireless communication. Therefore, this control task is completed with connectivity of the network. In a target detection problem, we must improve the performance of exploration as well as connectivity of the network. This study investigates the performances of the two types of random walk algorithm in navigation while loosely ensuring connectivity of the robotic network based on our previous study.