Application of GA-Optimized ANNs to Predict the Water Content,CO2 and H2S Absorption Capacity of Diethanolamine (DEA) in Khangiran Gas Sweetening Plant

Theoretical Foundations of Chemical Engineering - In this work, with the aim of accurate prediction of water content, H2S and CO2 absorption capacity of diethanolamine (DEA) solvent in Khangiran...     

An experimental study of forced convective heat transfer for fully developed Al 2 O 3 –water nanofluid in an annulus tube

Nanofluids have been known as practical materials to ameliorate heat transfer within diverse industrial systems. The current work presents an empirical study on forced convection effects of Al₂O₃–water nanofluid within an annulus tube. A laminar flow regime has been considered to perform the experiment in high Reynolds number range using several concentrations of nanofluid. Also, the boundary conditions include a constant uniform heat flux applied on the outer shell and an adiabatic condition to the inner tube. Nanofluid particle is visualized with transmission electron microscopy to figure out the nanofluid particles. Additionally, the pressure drop is obtained by measuring the inlet and outlet pressure with respect to the ambient condition. The experimental results showed that adding nanoparticles to the base fluid will increase the heat transfer coefficient (HTC) and average Nusselt number. In addition, by increasing viscosity effects at maximum Reynolds number of 1140 and increasing nanofluid concentration from 1% to 4% (maximum performance at 4%), HTC increases by 18%.     

Prolonged tamoxifen exposure selects a breast cancer cell clone that is stable in vitro and in vivo

The effects of long-term tamoxifen exposure on cell growth and cell cycle kinetics were compared between oestrogen receptor (ER)-positive (MCF-7) and ER-negative (MDA-MB-231) cell lines. In the MCF-7 cell line, prolonged tamoxifen exposure (0.5 mumol/l for > 100 days) blocked cells in G0-G1 of the cell cycle, and slowed the doubling time of cells from 30 to 59 h. These effects corresponded to an increase in the cellular accumulation of tamoxifen over time [mean area under concentration curve (AUC) = 77.92 mumoles/10(6)/cells/day]. In contrast, in the MDA-MB-231 cell line, long-term tamoxifen exposure had no obvious effect on the doubling time, and reduced cellular tamoxifen accumulation (mean AUC = 50.50 mumoles/10(6)/cells/day) compared to the MCF-7 cells. Flow cytometric analysis of MDA-MB-231 cells demonstrated that a new tetraploid clone emerged following 56 days of tamoxifen exposure. Inoculation of the MDA-MB-231 tetraploid clone and MDA-MB-231 wildtype cells into the opposite flanks of athymic nude mice resulted in the rapid growth of tetraploid tumours. The tetraploid tumours maintained their ploidy following tamoxifen treatment for nine consecutive serial transplantations. Histological examination of the fifth transplant generation xenografts revealed that the tetraploid tumour had a 25-30 times greater mass, area of haemorrhage and necrosis, a slightly higher mitotic index and was more anaplastic than the control neoplasm. The control wildtype MDA-MB-231 tumours maintained a stable ploidy following tamoxifen treatment until the eighth and ninth transplantation, when a tetraploid population appeared, suggesting that tamoxifen treatment may select for this clone in vivo. These studies suggest that prolonged tamoxifen exposure may select for new, stable, fast growing cell clones in vitro as well as in vivo.     

Unexplained physical symptoms: outcome, utilization of medical care and associated factors

BACKGROUND: Measurement of intracardiac hemodynamic parameters has been limited to brief periods in the acute care setting. We developed and evaluated an implantable hemodynamic monitor that is capable of measuring chronic right ventricular oxygen saturation and pulmonary artery pressure. METHODS AND RESULTS: The device consists of an electronic controller placed subcutaneously and two transvenous leads placed in the right ventricle (reflectance oximeter) and pulmonary artery (variable capacitance pressure sensor). Implantation was performed in 10 patients with severe left ventricular dysfunction. Average implant pulmonary artery pressures were systolic, 52 +/- 16 mm Hg; diastolic, 29 +/- 11 mm Hg; and mean, 40 +/- 12 mm Hg. The mean right ventricular oxygen saturation at implant was 51%. Provocative maneuvers, including postural changes, sublingual nitroglycerin, and bicycle exercise, demonstrated expected changes in measured oxygen saturation and pulmonary artery pressures over time. At follow-up of 0.5 to 15.5 months, there were no significant differences between pulmonary artery pressures or oxygen saturation values transmitted from the device and simultaneous measurement with balloon flotation catheters. Four of the pulmonary artery leads dislodged and three demonstrated sensor drift, whereas two of the oxygen saturation sensors failed. Four patients died and four received transplants. Pathological study did not demonstrate injury to the right ventricular outflow tract or pulmonic valve. CONCLUSIONS: Chronic measurement of hemodynamic parameters in the outpatient setting with implantable sensor technology appears to be feasible. The devices are well tolerated without significant untoward effects, and the sensors generally function well over time, providing reliable information. Clinical usefulness remains to be established.     

Adaptive stabilization of a class of nonlinear systems using high-gain feedback

This note presents a high-gain feedback stabilizing control algorithm in which the high-gain parameter is adapted on-line. The algorithm is developed for a class of nonlinear systems which can be viewed as the nonlinear counterpart of uniform rank systems. The system can be unknown except for a number of vital pieces of information. For single-input single-output linear systems such information is usually required in the traditional adaptive control literature.     

Complex formation of montmorillonite clay with polymers. Part 2: The use of montmorillonite clay–vinyl monomer complex as a comonomer in the copolymerization reaction of styrene–acrylonitrile monomers

The bulk copolymerization of styrene–acrylonitrile monomers using styrene‐N⁺–montmorillonite complex as a comonomer in the polymerization was studied. The X‐ray diffraction (XRD) analysis showed that part of the styrene‐N⁺–montmorillonite complex remained non‐dispersed (immiscible) and the copolymer was excluded from the interlayer of the immiscible part of the clay. The successive chemical extraction process revealed that a reasonable amount of the styrene–acrylonitrile copolymer was directly attached to the styrene‐N⁺–montmorillonite complex and enveloped the clay. Highly exfoliated clay lamella and nanospheres (3–5 nm) were observed by transmission electron microscopy (TEM). The montmorillonite clay assume two different morphologies, immiscible and exfoliated, on the basis of the XRD and TEM data. A simple method of calculation of the ratio of the exfoliated/immiscible amounts of the clay indicated that the amount of the styrene‐N⁺–montmorillonite complex exfoliated into separate lamella was 40 % (w/w) of the amount of the clay samples containing 2 % of the (styrene‐N⁺–montmorillonite complex) clay. This amount of exfoliated clay decreases with the increase of the concentration of the clay. The presence of the styrene‐N⁺–montmorillonite clay in the copolymerization reaction had a minor effect on both the copolymer composition and the molecular weight. Modification of the clay with the derivatized styrene monomer can achieve a nanocomposite using a percentage no more than 4 % (w/w) of complex in the copolymer. Copyright © 2004 Society of Chemical Industry     

The development and application of a multiple wavelength illumination technique for the vision-based process monitoring of aero-structure riveting

Airframe riveting is a critical process that requires high levels of process monitoring and quality assurance due to the very high risk associated with the failure of such joints. This paper describes the development of the enabling technology developed for a machine vision-based process monitoring system. One of the key factors affecting the performance of a machine vision system is the quality of the lighting. In the application described in this paper the available lighting was severely limited by the confined space in which the system had to operate. The problem was also compounded by the reflective nature of the objects to be examined. The initial images obtained were not suitable for further processing due to the presence of significant shadows and specular reflections. A novel solution to this problem based on multiple wavelength illumination and signal processing is presented along with results from experimental trials of the approach.     

General Solution for the Dynamic Modeling of Parallel Robots

In this paper, we present a general method to calculate the inverse and direct dynamic models of parallel robots. The models are expressed in a closed form by a single equation in which all the elements needed are expressed. The solution is given in terms of the dynamic models of the legs, the dynamics of the platform and some Jacobian matrices. The proposed method is applied in this paper on two parallel robots with different structures. Categories (2), (3).     

The effects of a monetary alternative on marijuana self-administration

We have used a variety of methods to characterize the genome of the archaeon Methanosarcina thermophila TM-1. Pulsed-field gel analysis indicates a genome size of 2.8 Mb. We have constructed a bacterial artificial chromosome (BAC) library of M. thermophila and have used it to generate physical maps for this organism. The library is made up of 384 clones with an average insert size of 58 kb representing 8.0 genome equivalents. The utility of the library for low-resolution physical mapping was shown by identifying NotI linking clones and using these to order the NotI macrorestriction fragments of M. thermophila into a 2.8 Mb map. Hybridization of nine single copy genes and a 16S rRNA sequence to these macrorestriction fragments forms the basis for the first genetic map in this organism. High-resolution physical maps, consisting of overlapping clones, have been created using HindIII fingerprints of BAC clones. In this way, we identified a minimal path of five clones that span a 270 kb NotI fragment. The ease of manipulating BAC clones makes the BAC system an excellent choice for the construction of low-resolution and high-resolution physical and genetic maps of archaeal genomes. It also provides a substrate for future genome-sequencing efforts.